2. Anolis
  3. Ambiane AP
Ambiane AP

Anolis Ambiane AP User manual

  • Hello! I've reviewed the provided document, which contains installation instructions for the ANOLIS AP light. This document details the steps for preparing the ceiling opening, connecting power and data, and installing the luminaire. I'm ready to help with any questions you might have about the installation process or features of the AP light.
  • What is the recommended hole diameter for mounting?
    When is the adapter ring used?
    What are the control options for the fixture?
INSTALLATION INSTRUCTIONS
ROBE lighting s. r. o. | Palackeho 416 | 757 01 Valasske Mezirici | Czech Republic | Tel.: +420 571 751 500 | E-mail: [email protected]
www.anolis.eu www.anolislighting.com
AMBIANETM AP
4
VERSION 1 / 24_05_2021
1
The unit must be installed by a qualified electrician in accordance with all national and local electrical
and construction codes and regulations.
STEP 1.A
CEILING OPENING
Prepare mounting hole with diameter between 212-214 mm.
STEP 2
PRIMARY POWER CONNECTION
1A
Install terminal blocks on cable and connect it to the Primary power connection of Ambiane AP‘s control unit.
1B
Use of the Adapter ring is recommended in case of a bigger ce-
iling opening. See step 6.B before connecting power and data
STEP 1.B
CEILING OPENING
INSTALLATION INSTRUCTIONS
ROBE lighting s. r. o. | Palackeho 416 | 757 01 Valasske Mezirici | Czech Republic | Tel.: +420 571 751 500 | E-mail: [email protected]
www.anolis.eu www.anolislighting.com
AMBIANETM AP
4
VERSION 1 / 24_05_2021
2
STEP 3
DATA CONNECTION (DMX OR DALI)
DMX CONNECTION
0V D- D+
Data Ground Data - Data +
1
2
Set the DIP switches to positions according to your operation
mode. The fixture can be controlled by DMX or DALI.
Set 11=OFF for control by DMX or DALI.
STEP 5
DIP SWITCH
1
Unscrew 2 screws on the control unit and remove plastic cover.
Install terminal blocks on cable and connect it to the control unit.
STEP 4
SECONDARY POWER CONNECTION 48V
Lift up springs on both sides, insert luminaire into ceiling opening
and release springs to hold lumaire in place.
STEP 6.A
LUMINAIRE INSTALLATION
Make sure power and data cables are connected before
this step.
Install terminal blocks on DMX or DALI cables and connect them
to the control unit.
1
INSTALLATION INSTRUCTIONS
ROBE lighting s. r. o. | Palackeho 416 | 757 01 Valasske Mezirici | Czech Republic | Tel.: +420 571 751 500 | E-mail: [email protected]
www.anolis.eu www.anolislighting.com
AMBIANETM AP
4
VERSION 1 / 24_05_2021
3
1
Lift up springs on both sides, insert luminaire into ceiling opening
and release springs to hold lumaire in place.
STEP 6.B
LUMINAIRE INSTALLATION WITH ADAPTER RING
2
3 4
Slide Adapter ring under the control unit and above both spring. Lift up both springs and slide Adapter ring under them.
Install Adapter ring to position as above.
INSTALLATION INSTRUCTIONS
ROBE lighting s. r. o. | Palackeho 416 | 757 01 Valasske Mezirici | Czech Republic | Tel.: +420 571 751 500 | E-mail: [email protected]
www.anolis.eu www.anolislighting.com
AMBIANETM AP
4
VERSION 1 / 24_05_2021
4
Click on Anti-Glare ring.
1
STEP 7
INSTALLTION OF ACCESSORIES - ANTI-GLARE RING
Insert the Anti-Glare ring into the Ambiane AP until three locks
snap into slots..
/