2. Anolis
  3. HP111
HP111

Anolis HP111 User manual

  • Hello! I've reviewed the installation instructions for the ANOLIS HP111 RECESSED light fixture. This document provides step-by-step guidance on how to prepare the ceiling, install the control unit, connect power and data, and secure the luminaire. I'm here to help you with any questions about the installation process outlined in the instructions.
  • What size cut-out is needed for the ceiling opening?
    How do you release the front frame?
    What is the first step in the installation?
    What is used to secure luminaire in the ceiling?
INSTALLATION INSTRUCTIONS
ROBE lighting s. r. o. | Palackeho 416 | 757 01 Valasske Mezirici | Czech Republic | Tel.: +420 571 751 500 | E-mail: [email protected]
www.anolis.eu www.anolislighting.com
AMBIANETM HP111 RECESSED
5
VERSION 1 / 24_05_2021
1
The unit must be installed by a qualified electrician in accordance with all national and local electrical
and construction codes and regulations.
STEP 1
PREPARE CEILING OPENING
Push in and twist the Front frame counter-clockwise to release it
from locks.
Take out the Front frame with optics.
Prepare cut-out with diameter of 133 mm.
STEP 2
DISASSEMBLING OF FRONT FRAME WITH OPTICS
Locks that are holding a Front frame of luminaire.
1 2
INSTALLATION INSTRUCTIONS
ROBE lighting s. r. o. | Palackeho 416 | 757 01 Valasske Mezirici | Czech Republic | Tel.: +420 571 751 500 | E-mail: [email protected]
www.anolis.eu www.anolislighting.com
AMBIANETM HP111 RECESSED
5
VERSION 1 / 24_05_2021
2
Place control unit above the ceiling through the ceiling opening.
STEP 3
CONTROL UNIT INSTALLATION
STEP 4
PRIMARY POWER CONNECTION
Mount the control unit to ceiling via two mounting holes.
Install terminal blocks on DMX or DALI cables and connect them
to the control unit.
DMX CONNECTION
0V D- D+
Data Ground Data - Data +
Set the DIP switches to positions according to your operation
mode. The fixture can be controlled by DMX or DALI.
Set 11=OFF for control by DMX or DALI.
STEP 5
DATA CONNECTION (DMX OR DALI)
1A 1B
Install terminal blocks to power cables and connect them in to primary power socket of the control unit.
1 2
INSTALLATION INSTRUCTIONS
ROBE lighting s. r. o. | Palackeho 416 | 757 01 Valasske Mezirici | Czech Republic | Tel.: +420 571 751 500 | E-mail: [email protected]
www.anolis.eu www.anolislighting.com
AMBIANETM HP111 RECESSED
5
VERSION 1 / 24_05_2021
3
Install terminal block on power cables and connect them to Secondary power socket of the control unit.
STEP 6
SECONDARY POWER CONNECTION 48V
STEP 7
LED UNIT CONNECTION
LED Unit Connection
TERMINAL
BLOCK + A B -
Colour of Wire Red White Blue Black
Strip 41 mm of LED unit‘s cable and then strip 6 mm of individual
wires to expose a conductor.
1
Install terminal block on LED module‘s cable and connect it to the
control unit.
Shorten the cables to necessary lengths.
2
3
Connected luminaire before installation.
INSTALLATION INSTRUCTIONS
ROBE lighting s. r. o. | Palackeho 416 | 757 01 Valasske Mezirici | Czech Republic | Tel.: +420 571 751 500 | E-mail: [email protected]
www.anolis.eu www.anolislighting.com
AMBIANETM HP111 RECESSED
5
VERSION 1 / 24_05_2021
4
Secure the luminaire in the ceiling opening with two holders,
adjustable via two screws located inside the luminaire. Use PH2
screwdriver to screw the holders into extended downward
position, until they are holding the luminaire firmly in the ceiling.
(Clockwise - holder moves down, Counter-clockwise - holder mo-
ves up)
STEP 8
LUMINAIRE INSTALLATION
Holders in extended downward position holding the fixture in the
ceiling opening.
Insert luminaire into ceiling opening.
Make sure all cables are connected before installation.
(Instructions above)
Top view of luminaire with extended holders.
3
1 2
INSTALLATION INSTRUCTIONS
ROBE lighting s. r. o. | Palackeho 416 | 757 01 Valasske Mezirici | Czech Republic | Tel.: +420 571 751 500 | E-mail: [email protected]
www.anolis.eu www.anolislighting.com
AMBIANETM HP111 RECESSED
5
VERSION 1 / 24_05_2021
5
STEP 9
ASSEMBLING FRAME WITH OPTICS.
Insert Top frame with optics into luminaire.Position the Top frame according to installation marks. Marks of
the luminaire and Top frame must be on top of each other.
Push Top frame into luminare and twist it clockwise, until it‘s locked
in the position.
STEP 10
INSTALLATION OF ACCESSORIES
RING LOUVER FOR 20° REFLECTOR
Insert the Ring Louver into the Top frame.
TOP Frame
Luminaire
1 2
3
/