Twin dual DVI input kit
Installation manual
Used in Galaxy NH-12, NH-12, NW-12
R9843041
R59770372/00
18/08/2009
Barco nv Simulation Division
Noordlaan 5, B-8520 Kuurne
Phone: +32 56.36.82.11
Fax: +32 56.36.84.86
E-mail: [email protected]
Visit us at the web: www.barco.com
Printed in Belgium
Changes
Barco p rovides this manua l ’as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied war-
ranties or m erchantability and fitness for a particular purpose. Barco may make improvements and/or cha nges to the product(s) and/or the
program(s) described in this publication at any time without notice.
This publication could contain technical inaccuracies or typographical errors. Changes are periodically m ade to the information in this
publication; these changes are incorporated in new editions of this publication.
Copyright ©
All rights r eserved. No part of this document m ay be copied, reproduced or translated. It s hall not other
wise be r ecorded, transmitted or
stored in a retrieval system without the prior written con sent of Barco.
Disposal Information
This equipment has required the ex traction and use of natural resources for its produc tion. It may contain hazardous substances for health
and env ironme nt. In order to avoid the dissemination of those substances in the environment and to diminish the pr essure on natural
resources, we encourage you to use the appropriate take-back systems. Those systems will reuse or recycle most of the materials of yo ur
end of life equipment in a sound way.
The crossed-out wheeled bin symbol invites you to use those systems. If you need more information on the collection, reuse and recycling
systems, please contact your local or r egional waste adm inistrator. You can also contact us for more information on the env ironmental
performances of ou r products.
Federal Communications Commission (FCC Statement)
This equipment has been tested and found to comply with the limits
for a clas s A digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection aga inst harm ful interference when the equipment is operated in a commercial
environment. T his eq uipment generates, uses, and can radiate radio frequenc y energy and , if not installed and used in a ccordance with
the instruction m anual, may cause harmful interference to r
adio communications. Operation of this equipment in a residential area may
cause harm ful interference, in which case the user will b e responsible for correcting any interference at his own expense
Guaran tee and Compensation
Barco provides a guarantee relating to perfect man ufacturing as part of the legally stipulated terms of guarantee. On receipt, the purchaser
must immediately inspect all delivered goods for dam age inc urred during transport, a s well as for material and manufacturing faults Barco
must be informed immediately in writing of any complaints.
The period of gu arantee begins on the date of transfer of risks, in the case of special systems and software on the date of comm issioning,
at latest 30 days after the transfer of risks. In the event of justified notice of complaint, Barco can repair the fault or p rovide a replacement
at its own discretion within an appropriate period. If this measure proves to be impossible or unsucc essful, the purchaser ca n demand a
reduction in the purchase pr ice or c ancellation of the contract. All o ther claims, in particular those relating to com pensa tion for direct or
indirect damage, and also damage attributed to the operation of s oftware as well as to other services provided by Barco, being a component
of the system or independent service, will be deemed invalid provided the dam age is n ot pro ven to be attributed to the absence of properties
guaranteed in writing or due to the intent or gr oss negligence or part of Barco.
If the purchaser or a third party carries out modifications or repairs o n go ods delivered by Barco, or if the goods are handled incorrectly,
in particular if the systems a re com missioned operated incorrectly or if, after the transfer of risks, the goods are s ubject to influences not
agreed upon in the contract, all guarantee claims of the purchaser will be rendered invalid. Not included in the guarantee coverage a re
system failures which are attributed to programs or special electronic circuitry provided by the purchaser, e.g. interfaces. Nor mal wear as
well as normal maintenance a re not subject to t he guara ntee provided by Barco either.
The environmental conditions as
well as the servicing and maintenance reg ulations specified in the this m anual m u st be com plied with by
the customer.
Trademarks
Brand and product name s mentioned in this manual m ay be trademarks, registered trademarks or copyrights of their respective holders.
All brand and product n ames mentioned in this man ual serve as commen ts or examples and are not to be understood as adv ertising for
the products or their m anufacturers.
Table of contents
TABLE OF CON TENTS
1. Safety instructions................................................................................................ 3
1.1 Safety during kit installation......................................................................................................... 3
2. Introduction ........................................................................................................ 5
2.1 Description of the twin dual DVI input layer ........................................................................................5
2.2 Twin dual DVI input kit............................................................................................................... 5
3. Installing the twin dual DVI input layer ..... ...... .... ...... ...... ..... ..... ...... ........ .. ...... .. .... .. .. ... 7
3.1 General overview of the installation procedure. . ................................................................................... 7
3.2 Removing the covers................................................................................................................ 7
3.2.1 Removing the cable basket................................................................................................... 7
3.2.2 Removing the rear cover ..................................................................................................... 8
3.2.3 Removing the top cover ...................................................................................................... 8
3.2.4 Removing the blank input cover plate........................................................................................ 9
3.3 Installing the twin dual DVI input layer ..............................................................................................10
3.4 Installing the covers ................................................................................................................. 12
3.4.1 Installing the top cov er ........................................................................................................12
3.4.2 Installing the rear cover .......................................................................................................13
3.4.3 Installing the cable basket . ...................................................................................................14
R59770372 TWIN DUAL DVI INPUT KIT 18/08/2009
1
Table of contents
2 R59770372 TWIN DUAL DVI INPUT KIT 18/08/2009
1. Safety instructions
1. SAFETY INSTRUCTIONS
1.1 Safety during kit installation
WARNING: The procedu res below ma y only b e performed by trained and Barco a uthorized te chnicians.
WARNING: Power down the projector and remove the power cord form the wall outlet before removing any
of the projector co vers.
WARNING: T he projector m ust be cooled do wn before rem oving any of the p rojector covers: wait for the cool
down cycle to finish after swi tching the projector to standby (the sound of the fans comes to a very low level)
and wait for 15 mo re m inutes before start ing any of t he pro cedures b elow.
CAUTION: Wear a wrist band which is connected to the ground while handling the electrostatic d ischarge
sensitive parts.
R59770372 TWIN DUAL DVI INPUT KIT 18/08/2009 3
1. Safety instructions
4 R59770372 TWIN DUAL DVI INPUT KIT 18/08/2009
2. Introduction
2. INTRODUCTION
2.1 Description of t he twin dual DVI input layer
Description
On the twin dual DVI input layer ,wefind two similar dual DVI connectors:
• digital data is received and transmitted to the multiplexer
• the analog part of the connector is not suppo rted.
• ED ID information is stored in the EEPROM.
The multiplexer allows to select the first DVI conne ctor or the other.
Schematic overview
DVI
1
80
TWIN DUAL DVI input layer
.
.
.
1
80
.
.
.
DVI
only digital
EID
MUX
EDID
EEPROM
only digital
EDID
EEPROM
DUAL DVI
RECEIVER
DUAL DVI
RECEIVER
Image 2-1
twin dual DVI input layer
2.2 Twin dual DVI input kit
Kit description
The k it contains the following items
Description Qty Image
twin dual DVI input board 1
fixing s cre w s 2
R59770372 TWIN DUAL DVI INPUT KIT 18/08/2009 5
2. Introduction
Description
Qty
Image
front plate
1
front bolts 4
packaging 1
-
installation manual 1
-
6 R59770372 TWIN DUAL DVI INPUT KIT 18/08/2009
3. Installing the twin dual DVI input layer
3. INSTALLING THE TWIN DUAL DVI INPUT LAYER
Overview
• General overview of the installation p rocedure
• Rem oving the covers
• Installing the twin dual DVI input lay er
• Installing the c overs
3.1 General overview of the installation procedure
Overview
Each of these steps is explained in detail in the procedures below.
1. Removing the covers
2. Installing the twin dual DVI input layer
3. Installing the cov ers
3.2 Removing the covers
Overview
• Rem oving the cable basket
• Rem oving the rear cover
• Rem oving the top cover
• Rem oving the blank input cover plate
3.2.1 Removing the cable basket
Necessary tools
No tools.
How to remove the cable basket?
1. Push the metal joggle to the front side of the projector
Image 3-1
Cable basket: push the joggle
2. First lift the c able basket, then bring it forward to remove it
R59770372 TWIN DUAL DVI INPUT KIT 18/08/2009
7
3. Installing the twin dual DVI input layer
Image 3-2
Cable basket: lift, then pull to remove it
3.2.2 Removing the rear cover
Necessary tools
Philips Ph2
How to remove the rear cover?
1. Remove the fix ing screw
Image 3-3
Rear cover: fixing screw
2. Lift the back side of the rear cover and pull it backward to remove it
Image 3-4
Tilt the back side of t he rear co
ver
Image 3-5
Pull the rear cover backward
Image 3- 6
Rear cover removed
3.2.3 Removing the top cover
Necessary tools
Phillips s crew dr iver Ph2
How to remove the top cover?
1. Remove the four fixing screws
8
R59770372 TWIN DUAL DVI INPUT KIT 18/08/2009
3. Installing the twin dual DVI input layer
- two at the front side of the projector
- one at the left side
- one at the right side
Image 3-7
Top cover: front screws
Image 3-8
Top cover: left screw
Image 3-9
Top cover: right screw
2. Lift the top cover to remove it
Image 3-10
Top cover: lift to remove
3.2.4 Removing the blank input cover plate
Necessary tools
Torx screw drive r T10
R59770372 TWIN DUAL DVI INPUT KIT 18/08/2009
9
3. Installing the twin dual DVI input layer
How to remove the blank input c o ver plate?
1. Unscrew and remove both fixing scre w s
A
Image 3-11
Blank input cover plate: fixi ng screws
Tip: Keep these screws: they will be used to fix the new front plate.
2. Remove the b lank input cover plate A (see im age above)
Image 3-12
Blank input cover plate removed
3.3 Installing the twin dual DVI input layer
Necessary tools
• Tor x screwdriver T 10
• Nut spanner 3/16”
How to install the twin dual DVI input layer?
1. Horizontally slide the twin dua l D VI input board in the open slot
10
R59770372 TWIN DUAL DVI INPUT KIT 18/08/2009
3. Installing the twin dual DVI input layer
Image 3-13
Twin dual DVI input board: installing (st ep 1)
Image 3-14
Twin du al DVI in pu t board: in stalling (step 2)
2. When the twin dual D VI input board is fully in, push it to the left to connect the board-to-board connectors to the P MP
Image 3-15
Twin dual DVI input board: push to the left to connect
Image 3-16
Twin dual DVI input board: connected to the PMP
3. Fix the twin dual DVI input board to the PM P using a
fixing screw
Image 3-17
Twin dual DVI input board: fix to the PMP using a screw
4. Fix the front plate of the twin dual DV I input layer to the projector us ing two fixing scr ew s
R59770372 TWIN DUAL DVI INPUT KIT 18/08/2009
11
3. Installing the twin dual DVI input layer
Image 3-18
Front plate: fixing
Note: These are the screws that were used to fix the blank front plate originally.
5. Fix the twin dual DVI input board to the front plate us ing the front bo lts
Image 3-19
Twin dual DVI input board: fixing it to the front plate
3.4 Installing the covers
Overview
• Installing the top cover
• Installing the rea r cover
• Installing the cable basket
3.4.1 Installing the top cover
Necessary tools
Phillips s crew dr iver Ph2
How to install the top cover?
1. Place the top cover in the correct position
12
R59770372 TWIN DUAL DVI INPUT KIT 18/08/2009
3. Installing the twin dual DVI input layer
Image 3-20
Top cover
2. Fix t he top cover us ing four screws
Image 3-21
Top cover: left screw
Image 3-22
Top cover: right screw
Image 3-23
Top cover: front screws
3.4.2 Installing the rear cover
Necessary tools
Philip screwdriver P h2
How to install the rear cover?
1. Put bo th clam ps of the rear cover in th e h oles on the top cover
Tip: The rear cover must b e tilted to perform this step!
R59770372 TWIN DUAL DVI INPUT KIT 18/08/2009
13
3. Installing the twin dual DVI input layer
Image 3-24
Installing t he rear cover: step 1
2. Slide the rear cover forward and bring the b ack side down
Image 3-25
Insta lling the rear cover: step 2
Image 3-26
Insta lling the rear cover: step 3
Image 3- 2 7
Installing the rear cover: step 4
3. Fix the rear cover us ing the fixing scre w
Image 3-28
Installing t he rear cover: step 5
3.4.3 Installing the cable basket
Necessary tools
No tools.
How to install the cable basket?
1. Fix the cab le basket to the projector: the hooks of the cable basket must fit the slots o f the projector
14
R59770372 TWIN DUAL DVI INPUT KIT 18/08/2009
3. Installing the twin dual DVI input layer
Image 3-29
Cable basket: slots on the projector
Image 3-30
Cable basket: hooks
2. Push the cable bas ket against the projector and then push it down until the joggle is locking (“click” sound)
Image 3-31
Cable basket: two steps to fi x it to the projector
R59770372 TWIN DUAL DVI INPUT KIT 18/08/2009 15
3. Installing the twin dual DVI input layer
Image 3-32
Cable basket: the joggle must lock
16 R59770372 TWIN DUAL DVI INPUT KIT 18/08/2009
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
Barco Twin dual DVI-D link Installation guide
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Barco DVI/D15 input board for iCon Installation guide
-
Barco NH-12 User manual
-
-
Barco iCon H250 Installation guide
-
-
-
Barco Galaxy NW-12 EX User guide
-
-
-
