Deagostini HMS Bounty Admiralty Ship User guide

PACK 01

PHASE PAGE

1Shipyard - part 01 5

2Keel 14

3Main # Frame 17

4Frame A 19

5Frame B 21

6Frame 1 23

7Gun Carriage and Cannon 25

8Culverin 30

Designing and production by Incipit srl

Assembly guide edited by Milanoedit srl - www.milanoedit.com

Published in Italy by De Agostini Publishing Italia S.p.A., 28100 Novara, Via G. da Verrazano 15

UNSUITABLE FOR CHILDREN UNDER 14. THE PRODUCT IS NOT A TOY

AND MUST BE USED UNDER ADULTS’ SUPERVISION.

THE PARTS MAY BE DIFFERENT FROM THE PICTURED ONES

PACK 01

3

1-07 1-08 1-09

1-10

1-01

1-03

1-06

1-02

1-04

1-05

ASSEMBLY INSTRUCTIONS

PACK 01

List of parts:

Shipyard Base:

Board MDF 1-07

Board MDF 1-08

Board MDF 1-09

Board MDF 1-10

Frames:

wooden plate 1-01

wooden plate 1-02

wooden plate 1-03

wooden plate 1-04

Keel:

wooden plate 1-05

Gun Carriage

plate 1-06

Cannon with ears and

cylinders

Culverin with fork

Brass sheet

PACK 01

4

Tools recommended for the

assembly

• Modelling hammer

• Cutter with interchangeable blades

• Vinyl glue (for wooden parts)

• Cyanoacrylate glue (for metal parts)

• Small clamp

• Hacksaw

• Tweezers

• Scissors

• Clips and set of rubber bands

• Modelling ﬁles (square and round)

• Modelling brushes

• Drill with thin bits

• Abrasive sponge

PACK 01

5

Side view

Top view

PHASE 01

SHIPYARD - part 01

A B C D

E

The shipyard is necessary to support ship structure, to keep frames perfectly perpendicular to

the keel, and to assembly all parts reinforcing the hull.

The shipyard will be built with parts supplied in the rst three Packs.

Board 1-07

ABoard 1-08

BBoard 1-09

CBoard 1-10

D

1

5

6

8

7

3

2

4

PACK 01

6

Lower view

Top view

F

G

Shipyard – Lower view

G

Shipyard - top view

F

PACK 01

7

The red highlighted parts are contained in Pack 01: the three pieces of the base (board 1-07, 1-08 and

1-09), the feet, and the guides for keel support (board 1-10).

1

Glue boards 1-07 and 1-08 together. Caution: the red areas show where to put vinyl glue.

General advice: Always clean glue in excess with a damp cloth when you glue parts together, and

wait for the glue to dry before proceeding.

2

Board 1-07

Board 1-08

Top view

PACK 01

8

Boards 1-07 and 1-08 glued together.

3

Board 1-07

Board 1-08

Top view

Turn upside down the two boards you have just glued together, detach pieces 1 and 2 from board 1-10 and

glue them, ﬁxing glue on the red highlighted parts.

4

2

1

Board 1-07

Board 1-08

Lower view

PACK 01

9

Again, turn the boards upside down, detach pieces 5 and 6 from board 1-10 and glue them, ﬁxing the glue on

the red highlighted parts.

5

6

Board 1-07

Board 1-08

Top view

Pieces 5 and 6 glued on boards 1-07 and 1-08

6

5

6

Board 1-07

Board 1-08

Top view

PACK 01

10

Boards 1-07, 1-08, 1-09 and pieces 5 and 6 glued together.

8

Board 1-09

Glue board 1-09 to board 1-08.

7

Board 1-09

Top view

5

6

Board 1-08

Board 1-07

PACK 01

11

Turn the shipyard base upside down, detach pieces 3 and 4 from board 1-10 and glue them, ﬁxing glue on

the red highlighted parts.

9

Board 1-09

Board 1-08

4

3

Lower view

The three boards 1-07, 1-08, 1-09 and pieces 1, 2, 3, and 4 glued together.

10

Board 1-09

Board 1-08

Board 1-07

3

4

2

1

Lower view

PACK 01

12

Pieces 5, 6, 7, and 8 glued on the top side of the shipyard base.

12

Board 1-09

Board 1-08

Board 1-07

7

5

8

6

Again, turn the shipyard base upside down, detach pieces 7 and 8 from board 1-10 and glue them as shown

in the picture.

11

Board 1-09

Board 1-08

Board 1-07

7

8

Top view

PACK 01

13

14

The completed shipyard base, top view.

13

The completed shipyard base, lower view.

14

Top view

Lower view

PACK 01

14

PHASE 02

KEEL

Plate 1-05 parts.

A

1

23

4

511

10

8

6

9

12

7

A

Stern section Bow section

Central section

PACK 01

15

T

A

G

L

I

A

R

E

To build the keel, use the paper templates of Set 01.

AStern section

The red line shows where to cut

the drawing.

The green arrows show the lines

where to glue the three sheets

of paper together (drawings A,

B and C).

A

T

A

G

L

I

A

R

E

BBow section

The red line shows where to

cut the drawing.

The green arrows show the

lines where to glue the three

sheets of paper together

(drawings A, B and C).

B

CCentral section

Print the drawing (Set 01) and

glue drawings A and B over it,

as shown in the picture.

The green arrows show the

lines where to glue the three

sheets of paper together

(drawings A, B and C).

C

AB

C

U

T

C

U

T

PACK 01

16

1

2

T

A

G

L

I

A

R

E

T

A

G

L

I

A

R

E

D

1

2 3 4 5 6

12

10

8

9

11

7

Picture D shows the three sheets of paper (A, B and C) glued together. Place the sheet of paper on a smooth

surface and arrange plate 1-05 pieces as shown in the picture.

D

The keel pieces laid on the sheet of paper.

1

Glue the pieces together following their numerical sequence with the help of picture D. Remove excessive glue

to prevent parts from gluing to paper.

Make sure that the keel matches exactly the drawing printed on the sheets of paper.

2

PACK 01

17

B

A

2

3

4

5

7

6

9

8

1

19

28

37

456

Plate 1-01 drawing

A

PHASE 03

MAIN # FRAME

The main # frame is the largest one.

Print drawing B of the main # frame (Set 01) at a scale of 1:1, on an A4 sheet of paper.

Print the drawing (Set 01) on an A4 sheet of paper at a scale of 1:1. The picture shows the numbers of pieces

from plate 1-01. The numbering of pieces matches the order in which they are to be assembled.

B

PACK 01

18

1

2

3

Fix the main # frame

pieces together with

vinyl glue, following the

sequential numbering.

Before glue dries, place

the frame on the sheet

of paper and check if

it matches the drawing

perfectly.

2

Plate 1-01 of the main #

frame.

1

When glue dries, gently

clean laser burns inside and

outside the frame with an

abrasive sponge.

3

PACK 01

19

B

A

2

3

4

5

7

6

9

8

1

19

28

37

456

Plate 1-02 drawing

A

FRAME A

After the main # frame, frames are labelled by numbers towards the direction of the stern and

by letters towards the direction of the bow. Print drawing B of frame A (Set 01) at a scale of

1:1, on an A4 sheet of paper.

Print the drawing (Set 01) on an A4 sheet of paper at a scale of 1:1. The picture shows the numbers of pieces

from plate 1-02. The numbering of pieces matches the order in which they are to be assembled.

B

PHASE 04

PACK 01

20

1

2

3

Plate 1-02 of

frame A.

1

When glue dries, gently

clean laser burns inside and

outside the frame with an

abrasive sponge.

3

Fix the frame pieces

together with vinyl glue,

following the sequential

numbering.

Before glue dries, place

the frame on the sheet

of paper and check if it

matches the drawing

perfectly.

2

Page is loading ...

Deagostini HMS Bounty Admiralty Ship User guide

Deagostini HMS Bounty Admiralty Ship User guide

Related papers

Other documents