NXP LFSTBBAT9 User guide

Freescale Semiconductor Document Number: MMA865xFCSTUG

User’s Guide Rev. 0, 10/2012

Contents

MMA865xFC Sensor Toolbox

User’s Guide

1 Introduction

The Freescale MMA865xFC sensor toolbox

accelerometer kit provides hardware and software for the

demonstration and evaluation of the Xtrinsic

MMA865xFC accelerometers (MMA8652FC,

MMA8653FC). This user’s guide shows you how to use

this kit.

The MMA865xFC kit includes the following:

• MMA865x interface board

• MMA8652FC accelerometer daughter board

• MMA8653FC accelerometer daughter board

The kit requires a USB-interface board to attach the kit

to a personal computer. Both items can be purchased on

the Freescale website.

• MMA865xFC kit, part number LFSTBEB865x

• MMA865x USB-interface board, part number

LFSTBUSB

• Optional 9V battery board (for non-volatile

memory datalogging), part number LFSTBBAT9

1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

2 About the MMA865x Accelerometers . . . . . . . . . . . . . . . 2

3 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

3.1 Connecting the kit . . . . . . . . . . . . . . . . . . . . . . . . . . 3

3.2 Installing the sensor toolbox software . . . . . . . . . . . 4

4 Understanding the Accelerometer Demonstrations . . . . . 8

4.1 Opening the sensor toolbox software . . . . . . . . . . . 8

4.2 Directional Flick application . . . . . . . . . . . . . . . . . . 10

4.3 Tilt Detection application . . . . . . . . . . . . . . . . . . . . 14

4.4 Orientation application. . . . . . . . . . . . . . . . . . . . . . 17

4.5 Graphical Datalogger application . . . . . . . . . . . . . 21

4.6 NVM Datalogger application . . . . . . . . . . . . . . . . . 26

4.7 Configuration screen . . . . . . . . . . . . . . . . . . . . . . . 29

4.8 Directional Tap with FIFO application . . . . . . . . . . 31

4.9 Directional Shake with FIFO application . . . . . . . . 36

4.10 Full-System Evaluation application . . . . . . . . . . . . 41

5 Running the Accelerometer Demonstrations. . . . . . . . . 62

5.1 Directional Flick application . . . . . . . . . . . . . . . . . . 62

5.2 Orientation (Portrait/Landscape) application . . . . . 62

5.3 Graphical Datalogger application . . . . . . . . . . . . . 62

5.4 Non-Volatile Memory Datalogger application . . . . 63

5.5 Directional Tap with FIFO application . . . . . . . . . . 63

5.6 Directional Shake with FIFO application . . . . . . . . 63

6 Revision History. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

MMA865xFC Sensor Toolbox User’s Guide, Rev. 0

2 Freescale Semiconductor, Inc.

2 About the MMA865x Accelerometers

The MMA8652FC device provides 12 bits of resolution and more features. The MMA8653FC device

provides 10 bits of resolution with fewer features. For more information, also see the MMA865xFC data

sheet.

Figure 1. MMA8652 block diagram

Figure 2. MMA8653 block diagram

C-to-V

Converter

SDA

SCL

I

2

C

Embedded

Functions

C-to-V

Internal

OSC

Clock

GEN

ADC

Converter

VDDIO

GND

X-axis

Transducer

Y-axis

Transducer

Z-axis

Transducer

32 Data Point

Configurable

FIFO Buffer

with Watermark

Freefall

and Motion

Detection

Transient

Detection

(i.e., fast motion,

jolt)

Enhanced

Orientation with

Hysteresis

and Z-lockout

Single, Double

Auto-WAKE/Auto-SLEEP Configurable with debounce counter and multiple motion interrupts for control

VDD

& Directional Tap

Detection

INT1

INT2

BYP

Interface

MUX

Voltage

Regulator

Gain AAF

Anti-Aliasing

Filter

C-to-V

Converter

SDA

SCL

I

2

C

Embedded

Functions

C-to-V

Internal

OSC

Clock

GEN

ADC

Converter

VDDIO

GND

X-axis

Transducer

Y-axis

Transducer

Z-axis

Transducer

Freefall

Detection

Orientation with

Hysteresis

and Z-lockout

Auto-WAKE/Auto-SLEEP Configurable with debounce counter and multiple motion interrupts for control

VDD

INT1

INT2

BYP

Interface

MUX

Voltage

Regulator

Gain AAF

Anti-Aliasing

Filter

MMA865xFC Sensor Toolbox User’s Guide, Rev. 0

Freescale Semiconductor, Inc. 3

3 Getting Started

To begin using the kit, connect it to your PC (Section 3.1, “Connecting the kit”) and install the sensor

toolbox software (Section 3.2, “Installing the sensor toolbox software”).

3.1 Connecting the kit

Select one of the two daughter boards and attach it to the USB interface board, as directed in the

LFSTBEB8491 Quick Start Guide included with the boards. When assembled, the device detection axes

are as shown in Figure 3.

Figure 3. Board assemblies

Figure 4 shows how the boards of the MMA865xFC kit fit together.

How the 3 axes are mapped

to the MMA865xFC kit

X

Z

Y

USB

Power switch

MMA865xFC Sensor Toolbox User’s Guide, Rev. 0

4 Freescale Semiconductor, Inc.

Figure 4. How the three boards are connected together

Connect the LFSTBUSB USB-interface board to a spare USB port on a Windows-based PC, using the

USB cable that comes with the USB board. If the board’s red power LED does not illuminate, check the

board’s power switch, near its USB connector.

3.2 Installing the sensor toolbox software

Perform the following procedure to install the software.

Near the end of this process, you will be asked if you want to install a serial-to-USB driver included with

the sensor toolbox. If you have been previously used Freescale's sensor toolbox software, these drivers

already are installed on your PC.

1. To download the sensor toolbox software, click the following link:

http://www.freescale.com/sensortoolbox.

The webpage, shown next, appears.

MMA8652FC (or MMA8653FC)

MMA865x USB-interface board

MMA845x interface board

accelerometer board

(LFSTBUSB)

MMA865xFC Sensor Toolbox User’s Guide, Rev. 0

Freescale Semiconductor, Inc. 5

2. Click the Download Software button.

The Sensor Toolbox Installer license agreement page appears.

3. Scroll down to the bottom of the page, shown below, and click the I Accept button.

4. Save the software’s installation executable file (SensorToolboxInstaller.exe) to your PC.

5. If you have not already connected the toolkit to your PC, perform the procedure in Section 3.1,

“Connecting the kit”.

6. Locate the installation file on your PC and double-click on it.

7. Proceed through the setup wizard’s series of dialog boxes.

During the process, you will be asked if you want a Sensor Toolbox icon added to your Start menu

and desktop.

MMA865xFC Sensor Toolbox User’s Guide, Rev. 0

6 Freescale Semiconductor, Inc.

8. When the Ready to Install dialog box, shown below, appears, review the installation configuration

and click the Install button.

A progress bar displays the status of the software installation and the final dialog box, shown

below, appears.

MMA865xFC Sensor Toolbox User’s Guide, Rev. 0

Freescale Semiconductor, Inc. 7

9. Do any of the following and click the Finish button:

— To install the Future Technology Devices International (FTDI) serial-to-USB communications

driver, enable the Install FTDI Driver checkbox.

— To launch the toolbox software upon completion of the setup, leave the Run Sensor Toolbox

checkbox enabled.

If you chose to install the FTDI driver, a command-line window briefly appears.

The application is now ready for use.

MMA865xFC Sensor Toolbox User’s Guide, Rev. 0

8 Freescale Semiconductor, Inc.

4 Understanding the Accelerometer Demonstrations

The sensor toolbox has several demonstrations for the MMA865xQ accelerometers, each showcasing the

built-in intelligence of the individual devices. The demos include tilt detection, orientation detection,

directional tap, and directional shake. There also is a full-system evaluation mode that allows you to

evaluate the sensor at the register level.

4.1 Opening the sensor toolbox software

To launch the toolbox software, either double-click on the application’s desktop icon or choose Start >

Programs > Sensor Toolbox > Sensor Toolbox. This displays the sensor toolbox’s hardware-detection

dialog box, shown below.

If the LFSTBUSB USB-interface board is connected properly, then the software will detect which of the

MMA865xQ daughter boards is attached to the evaluation board, and display the device-specific menus.

Upon device connection, the software displays the demo launcher menu, shown in the next illustration.

MMA865xFC Sensor Toolbox User’s Guide, Rev. 0

Freescale Semiconductor, Inc. 9

• To launch a demo, click on its box.

• To navigate to a different demo, close the browser window for the current demo and click on a

different demo box in the launcher menu, which remains in the background as long as the

application is running.

Full System Evaluation page 41

Directional Flick page 10

Hi Resolution Tilt Detection page 14

(MMA8652 only)

Low Resolution

Portrait/Landscape

page 17

Graphical Datalogger page 21

NVM Datalogger page 26

Directional Shake Low-Power

with FIFO

page 36

(MMA8652 only)

Directional Tap Low-Power

with FIFO

page 31

(MMA8652 only)

MMA865xFC Sensor Toolbox User’s Guide, Rev. 0

10 Freescale Semiconductor, Inc.

4.2 Directional Flick application

This demo enables you to evaluate the built-in algorithm for detecting flicks (transient events) with both

accelerometers. You can evaluate Freescale’s default configuration and modify those settings to tailor a

demonstration to your target application.

Launching the demo displays the Active screen.

4.2.1 Active screen

The Active screen contains a Direction Event Detected indicator with a direction text display, a picture

showing how to hold the device, and some pictures that can be manipulated by flicking the device. The

flick must be done in the direction indicated by the red arrow.

Note: Before

changing any

of the Active

screen’s

settings,

select the

Standby

option button.

MMA865xFC Sensor Toolbox User’s Guide, Rev. 0

Freescale Semiconductor, Inc. 11

4.2.2 Standby screen

Use the Standby screen to:

• Change the sample rate of the device

• Set the dynamic range

• Change the over-sampling setting

• Calibrate the device

• Change the device state and the parameters for detecting transient events

NOTE

Before changing any settings, enable Standby mode,

because the settings cannot be changed in Active mode.

After changing any configuration settings, enable Active mode,

to register the new settings with the device.

The screen contains the following

menu frames:

• Standby Active

• Operation Mode

• Dynamic Range

• Transient Settings

Note: To modify the

default

configuration,

first enable

the Standby

option button

on the left

side of the

screen.

MMA865xFC Sensor Toolbox User’s Guide, Rev. 0

12 Freescale Semiconductor, Inc.

Table 1. Directional Flick – Active/Standby screens

Screen

frame

Field or option Description

Operation

Mode

Sample Rate Enables you to change the rate at which the device acquires data.

Over-Sampling

Options for Data

Normal Mode Normal operation.

Hi Res Mode The device gives more accurate readings, but draws more current.

Low Power Mode The device draws less current than Normal mode, but at the

expense of accuracy.

Low Noise Low Power The device draws more current Normal mode, but less than Low

Power mode and reduces noise.

Auto Calibrate Directs the device to calculate the offsets for each axis (account for any error in

measurements). For maximum resolution, the calibration is done with a dynamic range of 8g

and a sample rate of 1.563 Hz.

Note: Before enabling this mode, place the device on a flat and stationary surface.

Dynamic

Range

•2g

•4g

•8g

Sets the range over which the accelerometer is acquiring data.

Standby

Active

Standby Sets the device to Standby mode.

Active Sets the device to Active mode.

•Standby Mode

• Wake Mode

• Sleep Mode

Indicates the device’s status (Read only).

Note: The device will never enter Sleep mode during this demo.

Transient

Settings

Default Transient

Settings

Sets the parameters for detecting flicks to their working values, as defined at the factory.

Bypass HPF

(High-Pass Filter)

Directs the application to use the raw accelerometer data before it has been passed through

the HPF.

Note: The Bypass HPF setting should normally be disabled.

• Enable X Flag

• Enable Y Flag

• Enable Z Flag

Allows flicks along these axes to trigger the “Event Detected” Indicator on the Demo Screen.

Note: Only the Y axis will move the pictures and correctly trigger the direction indicator.

If enabled, the X and Z axes will only trigger the Event Detected indicator on the Demo

screen.

Enable Latch Causes any triggered event to remain until the Status register is read. If this checkbox is not

enabled, the interrupt will only last as long as the event and the Status register will represent

the most-recent event.

This setting should be enabled for the flick detection to work properly. If it is disabled, the

events that are moving the pictures will constantly occur as you move the device and the

pictures will simply flick from end to end.

MMA865xFC Sensor Toolbox User’s Guide, Rev. 0

Freescale Semiconductor, Inc. 13

Transient

Settings

(

continued

)

Threshold Sets the threshold for flick events to be detected. Flicks at a smaller g-force than this value

are filtered out.

To move the slider, the Reset button must be clicked.

After the selection is made, click the Set button to change the setting.

Debounce This slider sets the amount of time that the configured conditions must be in place to trigger

the main flick event. Any event whose duration does not exceed this time will not trigger an

interrupt.

To move the slider, the Reset button must be clicked.

After the selection is made, click the Set button to change the setting.

Decrement

Debounce

Selecting this option causes the Debounce timer to be decremented each time an event fails

to reach the debounce time.

Clear Debounce Selecting this option causes the timer set by the Debounce slider to reset each time an event

fails to reach the debounce time.

Set Saves the new configuration settings after the repositioning of the Threshold and Debounce

sliders.

Reset Enables the moving of the Threshold and Debounce sliders.

Table 1. Directional Flick – Active/Standby screens (Continued)

Screen

frame

Field or option Description

MMA865xFC Sensor Toolbox User’s Guide, Rev. 0

14 Freescale Semiconductor, Inc.

4.3 Tilt Detection application

This tilt demo enables you to evaluate the tilt application using both accelerometers' data. It showcases the

tilt detection on the X and Y axes. The tilt angle degree is the addition of the coarse and the fine readings:

• The coarse reading is the integer angle.

• The fine reading is the fractional angle (also known as arcminutes).

4.3.1 Active screen

The Active screen enables you to evaluate the built-in algorithm for detecting the device’s tilt, in

conjunction with the device’s resolution mode (coarse or fine). You can evaluate the default configuration

and modify the settings to tailor the demonstration to your target application.

Note: Before changing any of the Active screen’s

settings, select the Standby option button.

Note: In order for the tilt to

be registered, the

device must be held

up so that it is facing

you (or held on a

desk on its edge).

MMA865xFC Sensor Toolbox User’s Guide, Rev. 0

Freescale Semiconductor, Inc. 15

4.3.2 Standby screen

Use the Standby screen to:

• Change the device Standby/Active state

• Set the dynamic range

• Change the sample rate of the device

• Change the over-sampling setting

NOTE

Before changing any settings, enable Standby mode,

because the settings cannot be changed in Active mode.

After changing any configuration settings, enable Active mode,

to register the new settings with the device.

Table 2. Tilt Detection – Active/Standby screens

Screen

frame

Field or option Description

Tilt Angle

Degree

Coarse Indicates the angle the device is being held at, along the X and Y axes (degrees).

Fine Shows the Arcminutes value of the angle (where an arcminute is equal to1/60 of a

degree).

MMA865xFC Sensor Toolbox User’s Guide, Rev. 0

16 Freescale Semiconductor, Inc.

Operation

Mode

Sample Rate Enables you to change the rate at which the device acquires data.

Note: The tilt demo will not function at the 1.563 Hz Sample Rate.

Over-Sampling

Options for Data

Normal Mode Normal operation.

Hi Res Mode The device gives more accurate readings, but draws more

current.

Low Power Mode The device draws less current than Normal mode does, but at

the expense of accuracy.

Low Noise Low Power The device draws more current than Normal mode does, but less

current than Low Power mode does, and reduces noise.

Auto Calibrate Directs the device to calculate the offsets for each axis (accounting for any error in

measurements). For maximum resolution, the calibration is done with a dynamic range of

8g and a sample rate of 1.563 Hz.

Note: Before enabling Auto Calibrate mode, place the device on a flat and stationary

surface.

Note: Before returning to active mode, it is necessary to set the Sample Rate back to a

usable value, because running Auto Calibrate sets the device to the 1.563 Hz

Sample Rate (a frequency at which the tilt application cannot function).

Dynamic

Range

•2g

•4g

•8g

Sets the range over which the accelerometer is acquiring data.

Standby

Active

Standby Sets the device to Standby mode.

Active Sets the device to Active mode.

• Standby Mode

• Wake Mode

• Sleep Mode

Indicates the device’s status (Read only).

Note: The device will never enter Sleep mode during this demo.

Table 2. Tilt Detection – Active/Standby screens (Continued)

Screen

frame

Field or option Description

MMA865xFC Sensor Toolbox User’s Guide, Rev. 0

Freescale Semiconductor, Inc. 17

4.4 Orientation application

The Orientation application demo enables you to evaluate the built-in Portrait/Landscape algorithm for

detecting orientation. Using this application, you can evaluate Freescale’s default configuration, as well as

change the settings to tailor the demonstration to your target application

4.4.1 Active screen

The Active screen contains a Portrait/Landscape gauge and a Back/Front gauge. The Portrait/Landscape

gauge has 5 options: UP, DOWN, LEFT, RIGHT, and Lockout. The Back/Front gauge shows 2 options:

BACK/FRONT.

The image below the gauge is a simulated mobile phone that displays the same orientation indicated by

the gauges. The information is provided by the device's accelerometer data.

Note: Before changing any of the Active screen’s

settings, select the Standby option button.

MMA865xFC Sensor Toolbox User’s Guide, Rev. 0

18 Freescale Semiconductor, Inc.

4.4.2 Standby screen

Use the Standby screen to:

• Set the device’s Standby/Active state

• Set the dynamic range

• Change the sample rate of the device

• Change the over-sampling setting

• Change the parameters for detecting orientation changes

NOTE

Before changing any settings, enable Standby mode,

because the settings cannot be changed in Active mode.

After changing any configuration settings, enable Active mode,

to register the new settings with the device.

Each menu frame’s fields and options are described in Table 3.

Note: Before changing

the Orientation

Detection values,

select the Enable

P/L button.

MMA865xFC Sensor Toolbox User’s Guide, Rev. 0

Freescale Semiconductor, Inc. 19

Table 3. Orientation – Active/Standby screens

Screen

frame

Field or option Description

Portrait /

Landscape

Detection

Display

Portrait/Landscape Shows the angle of the X and Y axes of the device.

If the device is tilted past the Z-lockout angle, then changes in the X and Y axes are

ignored and the gauge displays “Lock Out.” To resume orientation detection, rotate the

device away from the Z-lockout angle.

Back/Front Displays the Front/Back angle of the device.

Simulated Graphic

Display (mobile phone)

Orients the phone at the angle indicated by the data from the accelerometer.

Operation

Mode

Sample Rate Enables you to change the rate at which the device acquires data.

Over-Sampling Options

for Data

Normal Mode Normal operation.

Hi Res Mode The device gives more accurate readings, but draws more

current.

Low Power Mode The device draws less current than Normal mode does, but at

the expense of accuracy.

Low Noise Low Power The device draws more current than Normal mode does, but

less current than Low Power mode does, and reduces noise.

Auto Calibrate Directs the device to calculate the offsets for each axis (account for any error in

measurements). For maximum resolution, the calibration is done with a dynamic range

of 8g and a sample rate of 1.563 Hz.

Note: Before enabling this mode, place the device on a flat and stationary surface.

Dynamic

Range

•2g

•4g

•8g

Sets the range over which the accelerometer is acquiring data.

Standby

Active

Standby Sets the device to Standby mode.

Active Sets the device to Active mode.

•Standby Mode

• Wake Mode

• Sleep Mode

Indicates the device’s status.

Note: The device will never enter Sleep mode during this demo.

MMA865xFC Sensor Toolbox User’s Guide, Rev. 0

20 Freescale Semiconductor, Inc.

Orientation

Detection

settings

Enable P/L Enables the frame’s settings to be modified. Clearing the checkbox will prevent the

demo from functioning.

Set Default Settings Resets the frame’s settings to the default values defined at the factory.

Note: Selecting the “Set Default Settings” option will lock the values in the text boxes to

its right. If you want to change those values manually, then the “Set Default

Settings” option must be de-selected.

Portrait-To-Landscape

Tr i p A n gle

Shows the current value (Read only).

Landscape-To-Portrait

Tr i p A n gle

Shows the current value (Read only).

Z-Lock Angle Changes the Z-axis angle at which the device will ignore changes in orientation.

(For more information, see “Orientation application.”)

B/F Trip Angle (Back/Front Trip Angle)

Changes the range of z-axis angles within which the device considers itself facing front

and back.

P-L Trip Angle (Portrait-to-Landscape Trip Angle)

Changes the

midpoint

of the angle at which the device will change from portrait to

landscape orientation, or vice versa.

• For changing to right, the angle is measured down from the positive X axis.

• For changing to the left, landscape orientation, the angle is measured up from the

X-axis.

Hysteresis Angle Changes the

distance from the

midpoint

of the angle at which the device will change

from portrait to landscape orientation, or vice versa.

The actual trip angle for changing orientation is the P-L angle ± this angle.

Debounce Changes the time that the device waits after a physical orientation change is detected,

before triggering an orientation-change interrupt.

To move the Debounce slider, the Reset button must be clicked.

After the Debounce selection is made, click the Set button to change the setting.

Decrement Debounce Causes the Debounce timer to decrement each time that an event fails to reach the

debounce time.

Clear Debounce Causes the timer set by the Debounce slider to reset each time that an event fails to

reach the debounce time.

Set Saves the new configuration settings after the repositioning of the Threshold and

Debounce sliders.

Reset Enables you to move the Threshold and Debounce sliders.

Table 3. Orientation – Active/Standby screens (Continued)

Screen

frame

Field or option Description

Page is loading ...

NXP LFSTBBAT9 User guide

This manual is also suitable for

NXP LFSTBBAT9 User guide

Related papers

Other documents