Daikin B61-467 Installation guide

Brand: Daikin

Model: B61-467

Type: Installation guide

Phone: (855) 770-5678 | http://www.daikinac.com

4008862

ZONING BOX CONTROL BOARD

• Individually controlled dampers.

• Q-Adapt algorithm.

• Control of optional auxiliary heat (up to two stages).

• Supply temperature sensor.

• Seamless integration with the Indoor Unit Control.

o On/Off status.

o Fan speed Algorithm.

o Indoor Unit Set point.

o Operation Mode.

o Energy Efficiency Control Algorithm.

• It allows bus connection of up of 6 Wired Thermostats.

DZK-CB-3

Rev. 2.00

10-2018

TECHNICAL SPECS

Power supply and consumption

Type of power supply

Vac

V max

110 / 230 V

I max

250 mA

Frequency

60/50 Hz

Stand-by consumption

400 mW

Protection

Self-Resettable Fuse*

Expansion bus

Nº of ports

Shielded twisted pair

AWG 20 – 4 wired

Maximum wiring length

(Control board to Main thermostat)

130 ft (40 m)

V max

12 V

Connector for optional BACnet Interface board

Nº of ports

Communications protocol

MODBUS RS-485

Par – 19200 bps

Communication BACnet Network – BACnet/IP

Wireless communication

Communications protocol

Airzone proprietary protocol

Frequency

915 MHz

Radiation power

5 dBm

Maximum wireless reach

(Control Board to Wireless thermostat)

130 ft (40 m) in clear line of sight

Actuator control outputs

Nº of outputs

Vmax

± 12 V

Imax

150 mA

Auxiliary heat outputs

Nº of outputs

V max

24 / 48 V

I max

1 A

Alarm input

Type of alarm input

Dry contact (Normally Closed)

Operating temperatures

Storage

-4 … 158ºF (-20 … 70 ºC)

Operation

32 … 122ºF (0 … 50ºC)

Operating humidity range

5 … 90% (non-condensing)

Mechanical aspects

Protection class

IP 20

Weight (Mass)

0.45 lb (204 g)

Dimensions (WxH)

6.89x4.79 inch

(175.1 x121.6 mm)

*Electronic component that opens the electrical circuit and cycles back to a conductive

state after current is removed.

REPLACING THE CONTROL BOARD

Disconnect the power cable before starting the replacement of the DZK Zoning Box control board. Once the installation is finished reconnect the power cable.

Unscrew the cover, the screws are self-retaining.

Release the clamps holding the cables.

Disconnect all connectors.

Unscrew the four screws holding the plastic box

to the DZK zoning box control board.

Reinstall the cable clamps and insert the cover and screw in the retaining screws.

Install the new DZK zoning box control board,

using the same screws. Be sure the damper

connectors are on the upper

side.

Reconnect all the connectors as they were previously installed. Check that the damper

cables numbers correspond to the connectors numbers in the control board.

Once the installation is finished reconnect the power cable. Once the Zoning box control board is powered on, all the wireless thermostats

must be reset (see the Installation’s Manual); all system and zone parameters must be entered, following the initial installation procedure.

Phone: (855) 770-5678 | http://www.daikinac.com

4008862

WIRED THERMOSTAT CONFIGURATION

WIRELESS THERMOSTAT CONFIGURATION

When replacing the DZK zoning box control board, the wired thermostat configuration will not be reset. The time schedules will be the only feature reset. It is necessary to reprogram the personalized time schedules (see the User’s Manual).

In order to associate the Wireless Thermostats, the radio channel has had to be opened. To open the radio channel, press on SW1 (Main Control Board), the LED 19 will remain solid red for 15 min. You can also open the channel association radio

trough the Main Wired Thermostat (see the Installation’s Manual).

Select your language and press Airzone to

confirm.

To associate the thermostat, press Airzone.

Verify that received signal power is correct (30%

minimum) and press on Airzone to confirm.

Select the number of zone associated to the

thermostat.

Select Associate and press Airzone if additional

outputs are needed for this controller/zone.

If no additional outputs are required for this

zone, proceed to step 6.

Select Continue and press Airzone if no

additional outputs are required for this

thermostat/zone.

To finish the initial setup, press Airzone.

Select the desired output from the list of

available outputs and press Airzone.

WIRELESS LITE THERMOSTAT CONFIGURATION

In order to associate the Wireless Lite Thermostats, the radio channel has had to be opened. To open the radio channel, press on SW1 (Main Control Board), the LED 19 will remain solid red for 15 min. You can also open the channel association radio

trough the Main Wired Thermostat (see the Installation’s Manual).