anovafurnishings.com
888.535.5005 tel
TOOLS NEEDED: HARDWARE NEEDED:
Step-by-Step Installation Sequence
Product requires assembly before installation.
Examine the footing or slab for damage or defects. The footing or slab should be reinforced concrete rated at a
3,000 psi minimum and be cured for at least 28 days prior to the installation of the bench.
CAUTION: Oversized holes and holes drilled too deep in the concrete will make it dicult to set the anchor.
!
Hammer Drill
(4) 3/8"-16 x 1 1/2" Drop-in
Anchors
(4) 3/8”-16 x 1” SS
Button Head Cap Screw
(4) 3/8" SS or Rubber
Washers
Masonry Drill Bit Set
1/4", and 1/2"
3/8" Drop-in Anchor
Setting Tool
Hammer
Pencil
Allen Wrench Set
7/32"
Wire Brush
Level
Safety Glasses
Installation Instructions
Latitude Benches
Parkway Benches
Parkway
Latitude
1
Installation Instructions
Step-by-Step Installation Sequence
1.
2.
3.
5.
4.
6.
7.
8.
Place bench in the desired location. Mark the location of the holes with a
pencil. To verify the alignment of the anchor markings you may reference
page 3.
It is recommended that you start holes in sequential order from the
smaller to the larger drill bits to avoid oversized holes or holes drilled too
deep. Begin with 1/4" diameter drill bit followed by the 1/2" diameter bit.
Evacuate debris from mounting holes using compressed air and a steel wire
brush. This will create a clean environment for the anchor system.
Use the 3/8" drop-in anchor setting tool and hammer to x the anchor into
the drilled hole by inserting the narrow end of the tool into the anchor and
giving it several hammer blows.
Insert one 3/8"-16 x 1 1/2" drop-in anchor into the hole and use a hammer to
tap the anchor ush with the concrete.
Repeat steps 3 - 6 until all anchors are installed.
Align the mounting holes of the bench over top of the anchors.
Care should be given to avoid rubbing the powder coating o the foot.
A 3/8" rubber washer is a suitable replacement option. Mount the bench
to the anchors by fastening a button head cap screw and washer into each
anchor. Leave the hardware nger tight until all of them have been installed.
Verify that the bench is level before tightening the anchors. Tighten all of the
hardware with a 7/32" Allen wrench.
!
!
5
8.1
7
8.2
42
Latitude Benches
Parkway Benches
2
5
Installation Instructions
FOOT MOUNTS:
Latitude Benches
Parkway Benches
SECTION A-A
SCALE 1 / 4
A A
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
A A
B B
C C
D D
SHEET
1
OF
1
DRAWN
CHECKED
QA
MFG
APPROVED
dmetz 12/27/2017
DWG NO
TITLE
SIZE
D
SCALE
REV
1 / 4
.40
18.92
52.77
SECTION A-A
SCALE 1 / 4
A A
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
A A
B B
C C
D D
SHEET
1
OF
1
DRAWN
CHECKED
QA
MFG
APPROVED
dmetz 12/27/2017
DWG NO
TITLE
SIZE
D
SCALE
REV
1 / 4
.40
18.92
52.77
SECTION A-A
SCALE 1 / 4
A A
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
A A
B B
C C
D D
SHEET
1
OF
1
DRAWN
CHECKED
QA
MFG
APPROVED
dmetz 12/27/2017
DWG NO
TITLE
SIZE
D
SCALE
REV
1 / 4
.40
18.92
52.77
Ø.40"
(4 PLCS)
18.92"
37.88"
Latitude 4' Foot Mount
SECTION A-A
SCALE 1 / 4
A A
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
A A
B B
C C
D D
SHEET
1
OF
1
DRAWN
CHECKED
QA
MFG
APPROVED
dmetz 12/27/2017
DWG NO
TITLE
SIZE
D
SCALE
REV
1 / 4
.40
18.92
52.77
Ø.40"
(4 PLCS)
18.92"
61.75"
Latitude 6' Foot Mount
SECTION A-A
SCALE 1 / 4
A A
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
A A
B B
C C
D D
SHEET
1
OF
1
DRAWN
CHECKED
QA
MFG
APPROVED
dmetz 12/27/2017
DWG NO
TITLE
SIZE
D
SCALE
REV
1 / 4
.40
18.92
52.77
18.92"
52.77"
Parkway 6' Foot Mount
Ø.40"
(4 PLCS)
3
08/14/2018 Copyright 2018 ANOVA® Manufactured in the U.S.
Note: Please contact Customer Care at 1-866-797-1761 when ordering replacement parts.
-
1
-
2
-
3
Anova L1441 Installation guide
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Anova M2006 Installation guide
-
-
-
-
-
-
-
-
-
Other documents
-
TCE T9000-4S User manual
-
BendPak P-6 Owner's manual
-
-
Ogden OGM1900 Installation guide
-
-
-
-
-
-
