Fritsch ANALYSETTE 3 Operating instructions

Brand: Fritsch

Model: ANALYSETTE 3

Type: Operating instructions

Operang

instrucons

VIBRATORY SIEVE SHAKER

ANALYSETTE 3

Read the instrucons prior to performing any task!

Valid starng with: 03.X020/2019

Translaon of the original operang instrucons

Version 04/2022 Index 012

Fritsch GmbH

Milling and Sizing

Industriestrasse 8

D - 55743 Idar-Oberstein

Telephone: +49 6784 70-0

Email: inf[email protected]

Internet: www.fritsch.de

Cercaons and CE conformity

Cercaon

CE Conformity

Cercaons and CE conformity

Fritsch GmbH has been cered by the SGS-TÜV Saar GmbH.

An audit cered that Fritsch GmbH conforms to the requirements of the DIN EN

ISO 9001:2015.

The enclosed Conformity Declaraon lists the guidelines the FRITSCH instrument

conforms to, to be able to bear the CE mark and the UKCA mark!

Table of contents

1 Basic structure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2Safety informaon and use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.1 Requirements for the user. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.2 Scope of applicaon. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.2.1 Operang principle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.2.2 Amplitude control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.3 Obligaons of the operator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

2.4 Informaon on hazards and symbols used in this manual. . . . . . . . . . . . 11

2.5 Device safety informaon. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

2.6 Protecve equipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

2.7 Hazardous points. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

2.8 Electrical safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

2.8.1 General informaon. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

2.8.2 Protecon against restart. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

2.8.3 Overload protecon. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

3Technical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

3.1 Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

3.2 Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

3.3 Operang noise. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

3.4 Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

3.5 Current consumpon. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

3.6 Power consumpon. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

3.7 Electrical fuses. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

3.8 Load. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

3.9 Sieve mesh widths that can be used. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

3.10 Protecon class. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

4Installaon. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

4.1 Transport. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

4.2 Unpacking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

4.3 Seng up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

4.4 Ambient condions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

4.5 Electrical connecon. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

4.5.1 Adjusng the mains voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

5Inial start-up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

5.1 Switching on. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

5.2 Funcon check. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

5.3 Switching o. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Table of contents

6 Using the device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

6.1 Sieving with the ANALYSETTE 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

6.1.1 Fing and clamping the sieves. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

6.1.2 Mulple sieving. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

6.1.3 Feed quanty for dry or wet sieving. . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

6.2 Dry sieving. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

6.2.1 Sieving parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

6.2.2 Sieving aids. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

6.3 Wet sieving. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

6.3.1 Sieving parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

6.3.2 Weng agents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

6.3.3 Feeding the rinsing liquid. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

6.3.4 Extracng the passing parcles. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

6.3.5 Tips for wet sieving of dicult sieving stock. . . . . . . . . . . . . . . . . . . . . 26

6.4 Micro-precision sieving with the ANALYSETTE 3 PRO. . . . . . . . . . . . . . . . 26

6.4.1 Sieving parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

6.4.2 Feed quanty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

6.4.3 Fing the micro-precision sieves. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

6.4.4 Wet sieving with micro-precision sieves. . . . . . . . . . . . . . . . . . . . . . . . 28

6.5 Standby. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

6.6 Seng the sieving me. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

6.7 Seng the amplitude. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

6.7.1 Displaying the amplitude. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

6.8 Interval me. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

6.9 Saving and invoking the sengs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

6.10 Micro sieving. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

7 Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

7.1 AUTOSIEVE program. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

7.2 Connecng the PRO sieve shaker to the serial interface. . . . . . . . . . . . . . 31

7.3 Sound absorpon hood. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

7.4 TorqueMaster. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

7.4.1 Fing the TorqueMaster clamping device. . . . . . . . . . . . . . . . . . . . . . . 32

7.4.2 Clamping the TorqueMaster. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

7.4.3 Releasing the TorqueMaster. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

7.4.4 TorqueMaster malfuncons. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

7.4.5 Compability. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

7.5 Conversion to vibratory sieve shaker PULVERISETTE 0. . . . . . . . . . . . . . . 34

7.5.1 Conducng a grinding operaon. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Table of contents

8 Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

8.1 Cleaning the device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

8.2 Cleaning the test sieves (mesh wire sieves). . . . . . . . . . . . . . . . . . . . . . . . 38

9 Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

9.1 Maintenance of the TorqueMaster clamping device. . . . . . . . . . . . . . . . . 40

10 Repairs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

10.1 Checklist for troubleshoong. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

11 Disposal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

12 Guarantee terms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

13 Exclusion of liability. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

14 Safety logbook. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

15 Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Basic structure

1 Basic structure

Fig. 1: ANALYSETTE 3 SPARTAN

1 Plexiglas clamping lid

2 Test sieve

3 Belt clamping device

4 Vibratory plate

5 Knurled knob

6 Toothed belt

7 Sieve pan

8 Control panel SPARTAN

Basic structure

Fig. 2: ANALYSETTE 3 PRO with sieve stack for micro sieving

9 Clamping lid with a nozzle

10 Sieve spacer ring with 2 seals

11 Sieve pan with funnel

12 Clamping ring with fast locking clamp

13 Control panel PRO

Safety informaon and use

2 Safety informaon and use

2.1 Requirements for the user

This operang manual is intended for persons assigned with operang and mon-

itoring the Fritsch the ANALYSETTE 3. The operang manual and especially its

safety instrucons are to be observed by all persons working on or with this

device. In addion, the applicable rules and regulaons for accident prevenon

at the installaon site are to be observed. Always keep the operang manual at

the installaon site of the the ANALYSETTE 3.

People with health problems or under the inuence of medicaon, drugs, alcohol

or exhauson must not operate this device.

The the ANALYSETTE 3 may only be operated by authorised persons and serviced

or repaired by trained specialists. All commissioning, maintenance and repair

work may only be carried out by technically qualied personnel. Qualied per-

sonnel are persons who, because of their educaon, experience and training as

well as their knowledge of relevant standards, regulaons, accident prevenon

guidelines and operang condions, are authorised by those responsible for the

safety of the machine to carry out the required work and are able to recognize

and avoid possible hazards as dened for skilled workers in IEC 364.

In order to prevent hazards to users, follow the instrucons in this manual.

Malfuncons that impair the safety of persons, the the ANALYSETTE 3 or other

material property must be reced immediately. The following informaon

serves both the personal safety of operang personnel as well as the safety

of the products described and any devices connected to them: All maintenance

and repair work may only be performed by technically qualied personnel.

This operang manual is not a complete technical descripon. Only the details

required for operaon and maintaining usability are described.

Fritsch has prepared and reviewed this operang manual with the greatest care.

However, no guarantee is made for its completeness or accuracy.

Subject to technical modicaons.

2.2 Scope of applicaon

NOTICE

This laboratory instrument is designed for an 8-hour shi oper-

aon at 30 % duty cycle and not for connuous operaon.

The duty cycle is dened as the rao of load duraon to run

me. The run me is dened as load duraon plus pause me.

According to DIN EN 60034-1 (VDE 0530, IEC34-1) a connuous

operaon already takes place aer a standardised run me of

10 minutes. At 30 % duty cycle (DC = rao of load duraon to

run me) a load duraon of 3 minutes and a pause me of 7

minutes would be within standard.

If the standardised run me of 10 minutes is exceeded, then,

by denion, there would be a connuous operaon and

disproporonate temperature increases may occur, possibly

involving increased wear.

Safety informaon and use

The "ANALYSETTE 3 PRO" is a vercal vibrang laboratory sieve shaker used for

the exact separaon and classicaon of grain fracons. Dry bulk solids as well as

parcle collecves in suspensions can be analysed. Depending on feed quanty

and grain size, the test sieves and sieve pans can be clamped with dierent

diameters and heights.

CAUTION

The conversion of the "ANALYSETTE 3 PRO" to the micro mill

"PULVERISETTE 0" cannot be recommended, as the amplitude

control is unusable due to the ball collision malfuncons and

therefore has no ulity value. In this case, the "ANALYSETTE 3"

SPARTAN is more suitable.

However if you are using the PRO version with the PULVERI-

SETTE 0 grinding aachment, note that the amplitude must not

be set to > 2 mm, as otherwise damage will be caused to the

device, for which we accept no responsibility.

The "ANALYSETTE 3 SPARTAN" is equivalent in design to the PRO model, except

that the range of funcons is limited. The serial interface, electronic amplitude

control, amplitude display, interval me specicaon, micro sieving opon as

well as the standby funcon are not included.

2.2.1 Operang principle

The plasc housing contains a solid cast structure with an electronically con-

trolled electromagnet. Three permanently exible at springs carry the pole plate

of this magnet together with the vibratory plate, which is fastened to it. When

the magnet is switched on, the pole plate and vibratory plate are aracted and

spring back when it is switched o. The cast structure and magnet on one side

and the pole plate, vibratory plate and sieves on the other side form a vibratory

system.

The dierent number of sieves and sieving stocks or grinding aachments

changes the natural frequency of the vibratory system. For this reason, it is not

always possible to set the amplitude of the sieve shaker opmally e.g. with a

constant 50 Hz mains frequency present. The processor-controlled electronics of

the ANALYSETTE 3 PRO sieve shaker ensures a precisely adjustable, reproducible

sieve amplitude. This is achieved by bringing the frequency to smulate oscilla-

on closer to the natural frequency of the system or farther away from it. The

desired oscillaon amplitude of the sieve stack between 0.1 mm and 3.0 mm can

always be achieved - and with relavely low energy input. Therefore, connuous

operaon is possible without heang the sample material and the overall sieve

system.

2.2.2 Amplitude control

An electronic control circuit guides the sieve frequency of the ANALYSETTE 3 PRO

from a high to a low frequency range. In the meanme, a measuring system

records the amplitude and reports it to the control circuit unl the preselected

amplitude is reached.

This amplitude control takes place at regular intervals during the enre opera-

on. This makes it possible to react to changes in the sieve system.

The amplitude of the ANALYSETTE 3 SPARTAN is set manually with the Plus and

Minus key on the control panel and viewed on the lid.

Safety informaon and use

Safety informaon

2.3 Obligaons of the operator

Before using the the ANALYSETTE 3, this manual is to be carefully read and

understood. The use of the the ANALYSETTE 3 requires technical knowledge; only

commercial use is permied.

The operang personnel must be familiar with the content of the operang

manual. For this reason, it is very important that these persons actually receive

the present operang manual. Ensure that the operang manual is always near

the device.

The the ANALYSETTE 3 may exclusively be used within the scope of applicaons

set down in this manual and within the framework of guidelines put forth in this

manual. In case of non-compliance or improper use, the customer assumes full

liability for the funconal capability of the ANALYSETTE 3 and for any damage or

injury arising from failure to full this obligaon.

By using the the ANALYSETTE 3 the customer agrees with this and recognizes

that defects, malfuncons or errors cannot be completely excluded. To prevent

risk of damage to persons or property or of other direct or indirect damage,

resulng from this or other causes, the customer must implement sucient and

comprehensive safety measures for working with the the ANALYSETTE 3.

Neither compliance with this manual nor the condions and methods used

during installaon, operaon, use and maintenance of the the ANALYSETTE 3

can be monitored by Fritsch GmbH. Improper execuon of the installaon can

result in property damage and thus endanger persons. Therefore, we assume

absolutely no responsibility or liability for loss, damage or costs that result from

errors at installaon, improper operaon or improper use or improper mainte-

nance or are in any way connected to these.

The applicable accident prevenon guidelines must be complied with.

Generally applicable legal and other obligatory regulaons regarding environ-

mental protecon must be observed.

2.4 Informaon on hazards and symbols used in this manual

Safety informaon in this manual is designated by symbols. Safety informaon is

introduced by keywords that express the extent of the hazard.

DANGER

This symbol and keyword combinaon points out a directly

hazardous situaon that can result in death or serious injury if

not avoided.

WARNING

This symbol and keyword combinaon points out a possibly

hazardous situaon that can result in death or serious injury if

not avoided.

CAUTION

This symbol and keyword combinaon points out a possibly

hazardous situaon that can result in slight or minor injury if

not avoided.

Safety informaon and use

NOTICE

This symbol and keyword combinaon points out a possibly

hazardous situaon that can result in property damage if not

avoided.

Special safety informaon

To call aenon to specic hazards, the following symbols are used in the safety

informaon:

DANGER

This symbol and keyword combinaon points out a directly haz-

ardous situaon due to electrical current. Ignoring informaon

with this designaon will result in serious or fatal injury.

DANGER

This symbol and keyword combinaon designates contents and

instrucons for proper use of the machine in explosive areas

or with explosive substances. Ignoring informaon with this

designaon will result in serious or fatal injury.

DANGER

This symbol and keyword combinaon designates contents

and instrucons for proper use of the machine with combus-

ble substances. Ignoring informaon with this designaon will

result in serious or fatal injury.

WARNING

This symbol and keyword combinaon points out a directly

hazardous situaon due to movable parts. Ignoring informaon

with this designaon can result in hand injuries.

WARNING

This symbol and keyword combinaon points out a directly

hazardous situaon due to hot surfaces. Ignoring informaon

with this designaon can result in serious burn injuries due to

skin contact with hot surfaces.

Safety informaon in the procedure instrucons

Safety informaon can refer to specic, individual procedure instrucons. Such

safety informaon is embedded in the procedure instrucons so that the text can

be read without interrupon as the procedure is being carried out. The keywords

described above are used.

Example:

1. Loosen screw.

Safety informaon and use

Please observe!

2. CAUTION

Risk of entrapment at the lid.

Close the lid carefully.

3. Tighten screw.

Tips and recommendaons

This symbol emphasises useful ps and recommendaons as

wells as informaon for ecient operaon without malfunc-

on.

2.5 Device safety informaon

■Only use original accessories and original spare parts. Failure to observe this

instrucon can compromise the safety of the machine.

■Accident-proof conduct is to be strictly followed during all work.

■Comply with all currently applicable naonal and internaonal accident pre-

venon guidelines.

CAUTION

Wear hearing protecon!

If a noise level of 85 dB(A) is reached or exceeded, ear protec-

on should be worn to prevent hearing damage.

WARNING

The maximum accepted concentraon (MAC) levels of the rel-

evant safety guidelines must be observed; if necessary, venla‐

on must be provided or the machine must be operated under

an extractor hood.

DANGER

Explosion hazard!

−When Sieving oxidizable substances, e.g. metals or coal,

there is a risk of spontaneous combuson (dust explosion)

if the share of ne parcles exceeds a certain percentage.

When Sieving these kinds of substances, special safety

measures must be taken and the work must be supervised

from a specialist.

−The high-speed rotor mill is not explosion protected and is

not designed to sieve explosive materials.

■Do not remove the informaon signs.

Safety informaon and use

NOTICE

Immediately replace damaged or illegible informaon signs.

■Unauthorised alteraon of the the ANALYSETTE 3 will void Fritsch's declara-

on of conformity to European direcves and void the guarantee.

■Only use the the ANALYSETTE 3 when it is in proper working order, as

intended and in a safety- and hazard-conscious manner adhering to the

operang manual. In parcular, immediately recfy any malfuncons that

could pose a safety hazard.

■If, aer reading the operang manual, there are sll quesons or problems,

please do not hesitate to contact our specialised personnel.

2.6 Protecve equipment

Protecve equipment is to be used as intended and may not

be disabled or removed.

All protecve equipment is to be regularly checked for integ-

rity and proper funconing.

NOTICE

−The toothed belts must only be released or clamped in the

switched o state.

−Before switching on again, ensure that the two toothed

belts are evenly, ghtly clamped using the knurled knobs.

2.7 Hazardous points

■Crushing hazard at the sieve tensioning system

■Crushing hazard between vibratory plate and housing

2.8 Electrical safety

2.8.1 General informaon

The main switch separates the device from the mains on two poles.

2.8.2 Protecon against restart

Aer switching o at the main switch and switching on again, the START key must

be pressed for start-up.

2.8.3 Overload protecon

The mains fuse provides overload protecon.

Technical data

3 Technical data

3.1 Dimensions

Without sieve set:

350 x 200 x 400 mm (width x height x depth)

3.2 Weight

Net: 21 kg

Gross: approx. 27 kg

3.3 Operang noise

Emissions value of workplace according to DIN EN ISO 3746:2005 is up to 76.6

dB (A) for sieving gravel. The value uctuates, depending on frequency, grinding

stock and use of sieving aids.

When grinding with the PULVERISETTE 0, the operang noise is greatly reduced

by using the sound absorpon hood made of plexiglas (order no.: 00.0130.17).

3.4 Voltage

The device can be operated in two voltage ranges:

■Single phase alternang current 115V ± 10% and

■Single phase alternang current 230 V ± 10%.

(See also ⮫

Chapter 4.5 ‘Electrical connecon’ on page 18

)

It is not necessary to change the voltage range manually.

3.5 Current consumpon

Depending on the mains voltage, the maximum current consumpon is in the

ranges:

■115 V ® 0.44 A

■230 V ® 0.22 A

3.6 Power consumpon

Depending on the voltage range, the maximum power consumpon is approx. 50

3.7 Electrical fuses

■Fuse under mains switch (on the back of the device)

Replacement: 4 A M micro fuse, 5 x 20 mm

Technical data

3.8 Load

The maximum load of the ANALYSETTE 3 for the sieve set with sieving stock is up

to 3 kg!

3.9 Sieve mesh widths that can be used

■Dry sieving

100 µm to 25 mm (without sieving aids); 32 µm to 25 mm (with sieving aids)

■Wet sieving

20 µm or greater

■Micro sieving (PRO version only)

5 µm to 100 µm

3.10 Protecon class

IP 54

Installaon

4Installaon

4.1 Transport

The device is delivered in a cardboard box. In the case of delivery with several

accessories, the device is delivered in a transport crate.

WARNING

Improper liing can lead to personal injury or property

damage. The machine must only be lied with suitable equip-

ment by qualied personnel.

The guarantee excludes all claims for damage due to improper transport.

4.2 Unpacking

■In the case of delivery in a crate, pull out the nails that fasten the lid to the

surrounding packaging.

■Remove the lid.

■Take out the accessories.

■To remove the device, three hexagon screws under the wooden plate must

be unscrewed.

■Compare the contents of the delivery with your order.

Keep the wooden plate, screws and washers, as this transport

securing device must be reaached in the case of further

transport or return.

4.3 Seng up

NOTICE

Allow the device to acclimase for two hours before commis-

sioning. High temperature dierences can lead to condensaon

in the device and damage to the electronics aer switching on.

Strong temperature uctuaons can occur during transport or interim storage.

Depending on the temperature dierence between the installaon site and the

transport or storage environment, condensaon can form inside the device. This

can damage the electronics if the devices are switched on too early. Wait for at

least two hours aer setup before switching on the device.

■Place the device on a at, stable surface. It does not have to be fastened to

the surface. Leave sucient space beside the device for placing the accesso-

ries used.

■The space behind the device must be freely accessible so that the main

switch on the mains connecon can be accessed quickly in case of emer-

gency.

■The device rests on three at coil spring assemblies. Level the sieve shaker:

Installaon

–ANALYSETTE 3:

Level the sieve shaker by screwing these feet in or out so that during

sieving, the sieving stock is evenly distributed across the enre sieve

surface.

4.4 Ambient condions

WARNING

Mains voltage!

−The device may only be operated indoors.

−The surrounding air may not carry any electrically conduc-

ve dust.

−Maximum relave humidity 80% for temperatures up to

31°C, linearly decreasing down to 50% relave humidity at

40°C.

■The room temperature has to stay between 5 - 40°C.

■Altudes up to 2000 m

■Degree of polluon 2 according to IEC 664.

4.5 Electrical connecon

Before establishing the connecon, compare the voltage and current values

stated on the type plate with the values of the mains system to be used.

CAUTION

Ignoring the values on the type plate may result in damage to

the electrical and mechanical components.

4.5.1 Adjusng the mains voltage

4.5.1.1 Version SPARTAN and PRO (valid ll serial number 05727)

CAUTION

If the value 01 is set at a voltage of 230V~, it will result in a

defect in the sieve shaker during operaon. Failure to observe

this will render void the guarantee, and releases us from lia-

bility for any resulng damage to the device.

NOTICE

Only qualied personnel may change the voltage range on the

device!

1. Switch main switch to "0".

2. Switch the device on at the main switch while holding down the Stop key.

The device is now in "Setup" mode.

Installaon

3. The "Sieving Time" display now shows the default seng "02" for 230 V,

"01" for 115 V.

4. These values can be changed with the "Sieving Time" +/- key and adapted

to the mains voltage.

■230 V - 02

■115 V - 01

Save the set values by clicking the stop key.

5. Aer making adjustments, switch on the main switch again.

4.5.1.2 Version PRO (valid from serial number 06000) and Version SPARTAN (valid from serial number 05000)

CAUTION

If the value 01 is set at a voltage of 230V~, it will result in a

defect in the sieve shaker during operaon. Failure to observe

this will render void the guarantee, and releases us from lia-

bility for any resulng damage to the device.

NOTICE

Only qualied personnel may change the voltage range on the

device!

1. Switch main switch to "0".

2. Switch the device on at the main switch while holding down the Stop key.

The device is now in "Setup" mode.

3. The "Sieving Time" display now shows the default seng "02" for 230 V,

"01" for 115 V.

4. These values can be changed with the "Sieving Time" +/- key and adapted

to the mains voltage.

■230 V - 02

■115 V - 01

Save the set values by clicking the stop key.

5. Aer making adjustments, switch on the main switch again.

Inial start-up

5Inial start-up

Perform inial start-up only aer all work as described in ⮫

Chapter 4 ‘Installa-

on’ on page 17

has been carried out.

5.1 Switching on

■The device must be connected to the power supply if this has not been done

already.

■Switch on the device with the main switch on the back of the device.

■The POWER lamp on the control panel lights up.

■The displays show the default seng.

5.2 Funcon check

■Clamp 2 test sieves (2) with clamping lid (1).

■Set the amplitude to 2 mm (See ⮫

Chapter 6.7 ‘Seng the amplitude’

on page 29

)

■When everything is correctly clamped, start the funcon check with "START".

Whether the set amplitude has been reached can be checked

on the display or on the amplitude plate on the lid.

5.3 Switching o

■Press the STOP key and switch o the main switch.

Page is loading ...

Fritsch ANALYSETTE 3 Operating instructions

Fritsch ANALYSETTE 3 Operating instructions

Fritsch ANALYSETTE 3 Operating instructions

Related papers

Other documents