OZCO 16622 Hammered Dome Cap Nut Operating instructions

Brand
OZCO
Model
16622 Hammered Dome Cap Nut
Type
Operating instructions

This manual is also suitable for

V2.00 - Installation Instructions, Specifications and Project Plans are effective 10/5/2016 . This information is updated periodically
and should not be relied upon after 2 years from 10/5/2016 . Please visit OZCOBP.com to get current information.
Installation Instructions,
1-1/2" Hex Cap Nuts
Dome Cap Nuts
1" Hex Cap Nuts
1
Installation Instructions, Cap Nuts
56621 & 86621
1-1/2" Hex Cap Nuts 56622 & 86622
Dome Cap Nuts 56681 & 86681
1" Hex Cap Nuts
All Cap Nuts function the same
Hex Cap Nuts are standard on most products.
Dome Cap Nuts are standard on hinges.
Either are suitable in place of one another plus a variety of other uses.
Increased holding power of fasteners with additional surface area.
V2.00 - Installation Instructions, Specifications and Project Plans are effective 10/5/2016 . This information is updated periodically
and should not be relied upon after 2 years from 10/5/2016 . Please visit OZCOBP.com to get current information.
Suggested Tools
(others may be required)
3
Installation Instructions, Cap Nuts
V2.00 - Installation Instructions, Specifications and Project Plans are effective 10/5/2016 . This information is updated periodically
and should not be relied upon after 2 years from 10/5/2016 . Please visit OZCOBP.com to get current information.
Recommneded Fastener:
OWT Timber Screws
1-1/2" Hex Cap Nut Installation
Installation Instructions, Cap Nuts 4
use this
end on
cap use this end
on Timber
Screw
Tool required
3/8" Driver (not
included)
step 2
securing
Cap
finger tight
step 1
securing
fastener (not
included)
V2.00 - Installation Instructions, Specifications and Project Plans are effective 10/5/2016 . This information is updated periodically
and should not be relied upon after 2 years from 10/5/2016 . Please visit OZCOBP.com to get current information.
1" Hex Cap Nut Installation
Installation Instructions, Cap Nuts 5
Recommneded Fastener:
#8x1"
(phillips head shown)
step 1
securing
fastener (not
included)
Cap (finger tight)
4mm Hex
Tool required
1/4" Driver (not
included)
step 2
securing
Cap
finger tight
V2.00 - Installation Instructions, Specifications and Project Plans are effective 10/5/2016 . This information is updated periodically
and should not be relied upon after 2 years from 10/5/2016 . Please visit OZCOBP.com to get current information.
Recommneded Fastener:
OWT Timber Screws
Dome Cap Nut Installation
Installation Instructions, Cap Nuts 6
use this end
on Timber
Screw
Tool required
3/8" Driver (not
included)
step 1
securing
fastener (not
included)
step 2
securing
Cap
finger tight
V2.00 - Installation Instructions, Specifications and Project Plans are effective 10/5/2016 . This information is updated periodically
and should not be relied upon after 2 years from 10/5/2016 . Please visit OZCOBP.com to get current information.
Disassembly Method...if difficult
Installation Instructions, Cap Nuts 7
Dome Cap Nut
Lightly tap with
RUBBER mallet,
then remove with
fingers
use this
end on
cap
driver
Hex Cap Nut (both sizes)
Apply lubricant, then remove
with driver
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

OZCO 16622 Hammered Dome Cap Nut Operating instructions

Brand
OZCO
Model
16622 Hammered Dome Cap Nut
Type
Operating instructions
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents