FläktGroup CentriFlow 3D GMPM FC101_FC102 Quick start guide

Brand: FläktGroup

Model: CentriFlow 3D GMPM FC101_FC102

Type: Quick start guide

FläktGroup CentriFlow 3D GMPM FC101_FC102 is a frequency converter for controlling and adjusting the speed of plug fans, ranging from 0.8 kW to 15 kW. With high efficiency (IE4) due to permanent magnets in the rotor, it offers better part load efficiency compared to asynchronous motors. Featuring a special algorithm for PM motors, it optimizes motor performance and enhances operational efficiency.

PUR (A, B, C, D)

SLIDE IN ROTOR CASSETTE

FläktGroup DC_10035GB_20180514_R0

Specifications are subject to change without further notice

FLÄKTGROUP OFFERS A WIDE RANGE OF PER-

MANENT MAGNET MOTORS (PM) AND FREQUENCY

CONVERTERS FOR PLUG FANS. POWER RANGE IS

FROM 0,8 KW TO 15 KW.

CONTENT PAGE

1. General ................................................................................................ 2

2. Fan and Motor data ......................................................................... 3

Frequency converter data

................................................................... 4

4. Separate frequency converter dimensions ............................................... 5

5. Speciﬁcation for motor ........................................................................................ 5

6. Installation ................................................................................................................ 5

7. Connection diagram ............................................................................................. 6

8. Cabling ........................................................................................................................7

9. Control signals ........................................................................................................ 8

10. Start up and functional testing....................................................................... 8

11. Parameters ............................................................................................................. 8

12. Operating panel FC101 .....................................................................................9

13. Operating panel FC102 ..................................................................................10

14. Alarms and warnings ...................................................................................... 11

CENTRIFLOW 3D PLUG FAN GMPM

FC101 AND FC102 FREQUENCY CONVERTER

QUICK GUIDE

FC101 and FC102 frequency converters for plug fan GMPM -

Quick Guide

FläktGroup DC_10035GB_20180514_R0

Specifications are subject to change without further notice

1. GENERAL

FläktGroup offers a wide range of permanent magnet motors (PM)

and frequency converters for plug fans. Power range is from 0,8

kW to 15 kW. PM motor has high efﬁciency (IE4) due to the per-

manent magnets in rotor. Also part load efﬁciency is better com-

pared to asynchronous motors.

When rotor has no losses and stator needs less current the tem-

perature inside the motor is lower, which gives longer running

time for bearings.

Direct on-line connection is not possible for perma-

nent magnet motors. Frequency converter is always

needed. This controller has a special algorithm for

PM motors. Frequency converter is programmed

with fan and motor speciﬁc parameters.

FC101 and FC102 frequency converters are delivered loose. They

are to be mounted by the customer.

Frequency converter should be mounted near the fan.

Motor cable shall not be longer than 10 m. With longer cables

some motor parameters should be changed. Frequency converter

is deli vered with 3.5 m motor cable for fan sizes up to 050. For

bigger fans motor cable length is 4.5 m. Cable is connected at the

motor end.

PM motor

IP54 and IP55 frequency converter mounted at AHU casing.

FC101 Frequency controller FC102 Frequency controller

FC101 and FC102 frequency converters for plug fan GMPM -

Quick Guide

FläktGroup DC_10035GB_20180514_R0

Specifications are subject to change without further notice

2. FAN AND MOTOR DATA

Fan code incl.

Motor and drive

Power

[kW]

Motor Current

[A]

Motor frame

Size IEC

Fan max speed

[rpm]

Fan max freq.

[Hz]

Motor speed

[rpm] at 50 Hz

Motor nominal

speed [rpm]

GMPM-1-bb-025-11e0 1,1 2,4 71 5000 250 1000 4500

GMPM-1-bb-025-06e0 0,8 1,9 71 3960 198 1000 3000

GMPM-1-bb-028-15e0 1,5 3,1 71 4300 215 1000 4500

GMPM-1-bb-028-08e0 0,8 1,9 71 3630 182 1000 3000

GMPM-1-bb-031-30e0 36,8 71 4660 233 1000 4500

GMPM-1-bb-031-22e0 2,2 6,8 71 4140 207 1000 4500

GMPM-1-bb-031-15e0 1,5 3,4 71 3700 185 1000 3600

GMPM-1-bb-031-06e0 0,8 1,9 71 2900 145 1000 3000

GMPM-1-bb-035-30e0 37,5 90 3940 263 750 3600

GMPM-1-bb-035-22e0 2,2 4,4 71 3400 170 1000 3000

GMPM-1-bb-035-15e0 1,5 3,5 71 3120 156 1000 2500

GMPM-1-bb-035-08e0 0,8 3,5 71 2460 123 1000 2500

GMPM-1-bb-040-55e0 5,5 13 90 3940 263 750 3000

GMPM-1-bb-040-40e0 49,1 90 3550 237 750 3000

GMPM-1-bb-040-30e0 39,1 90 3190 213 750 3000

GMPM-1-bb-040-22e0 2,2 4,4 71 2700 135 1000 3000

GMPM-1-bb-040-15e0 1,5 3,5 71 2440 122 1000 2500

GMPM-1-bb-040-08e0 0,8 3,5 71 2000 100 1000 2500

GMPM-1-bb-045-55e0 5,5 13 90 3050 203 750 3000

GMPM-1-bb-045-40e0 49,1 90 2650 177 750 3000

GMPM-1-bb-045-30e0 39,1 90 2500 167 750 3000

GMPM-1-bb-045-15e0 1,5 3,9 71 2200 110 1000 1800

GMPM-1-bb-045-11e0 1,1 3,9 71 1800 90 1000 1800

GMPM-1-bb-050-75e0 7,5 16,2 112 2840 142 1000 2600

GMPM-1-bb-050-55e0 5,5 13 90 2400 160 750 3000

GMPM-1-bb-050-36e0 3,6 7,8 90 2100 140 750 1800

GMPM-1-bb-050-22e0 2,2 5,2 90 1900 127 750 1440

GMPM-1-bb-050-15e0 1,5 3,9 71 1760 88 1000 1800

GMPM-1-bb-056-75e0 7,5 16,3 112 2380 119 1000 2100

GMPM-1-bb-056-55e0 5,5 10,8 90 2150 143 750 2000

GMPM-1-bb-056-40e0 410,8 90 1930 129 750 2000

GMPM-1-bb-056-36e0 3,6 7,8 90 1850 123 750 1800

GMPM-1-bb-056-22e0 2,2 6,5 90 1500 100 750 1100

GMPM-1-bb-063-81e0 11 22,4 112 2240 112 1000 2000

GMPM-1-bb-063-75e0 7,5 17 112 1950 98 1000 1800

GMPM-1-bb-063-55e0 5,5 11,5 112 1760 88 1000 1600

GMPM-1-bb-063-40e0 49,7 90 1550 103 750 1700

GMPM-1-bb-063-22e0 2,2 6,5 90 1200 80 750 1100

GMPM-1-bb-071-81e0 11 21 112 1840 92 1000 1650

GMPM-1-bb-071-75e0 7,5 17,3 112 1620 81 1000 1500

GMPM-1-bb-071-55e0 5,5 12 112 1460 73 1000 1300

GMPM-1-bb-071-40e0 412 112 1320 66 1000 1300

GMPM-1-bb-071-22e0 2,2 6,5 90 1075 72 750 1100

GMPM-1-bb-080-85e0 15 34,5 132 1655 83 1000 1655

GMPM-1-bb-080-81e0 11 22,9 132 1500 75 1000 1350

GMPM-1-bb-080-75e0 7,5 16,8 112 1315 66 1000 1230

GMPM-1-bb-080-55e0 5,5 12,2 112 1185 59 1000 1100

GMPM-1-bb-080-30e0 312,2 112 965 48 1000 1100

GMPM-1-bb-090-75e0 7,5 16,4 132 1093 55 1000 1000

GMPM-1-bb-090-81e0 11 22,9 132 1240 62 1000 1140

GMPM-1-bb-090-85e0 15 35,2 132 1375 69 1000 1375

e = 1 for FC101

e = 5 for FC102

FC101 and FC102 frequency converters for plug fan GMPM -

Quick Guide

FläktGroup DC_10035GB_20180514_R0

Specifications are subject to change without further notice

3. FREQUENCY CONVERTER DATA

Mains supply (L1, L2, L3)

Supply voltage 380-480 V ±10%

Supply frequency 50/60 Hz

Max. imbalance temporary

between mains phases 3.0% of rated supply voltage

True Power Factor (λ)≥ 0.9 nominal at rated load

Displacement Power Factor

(cosφ) near unity (> 0.98)

Switching on input supply

L1, L2, L3 (power-ups) maximum 2 times/min.

Environment according to

EN60664-1

overvoltage category III/

pollution degree 2

Motor output (U, V, W)

Output voltage 0 - 100% of supply voltage

Output frequency

for PM motors

FC101 0 - 390 Hz

FC102 0-590 Hz

Digital inputs:

Programmable digital inputs 4

Logic PNP or NPN

Voltage level 0 - 24 V DC

Analog inputs:

Number of analog inputs 2

Modes Voltage or current

Voltage level 0 to + 10 (scalable)

Current level 0/4 to 20 mA (scalable)

Analog output:

Number of programmable

analog outputs

FC101 = 2

FC102 = 1

Current range at analog output 0/4 - 20 mA

Digital output:

Programmable digital 2

Voltage level at digital FC101 = 17 V

FC102 = 24 V

Max. current at digital output: FC101 = 20 mA

FC102 = 40 mA

Relay outputs:

Programmable relay outputs 2

Max. terminal load

(AC-1 Resistive load)

FC101 = 250 V AC, 3 A

FC102 = 240 V AC, 2 A

Control card, 10 V DC output:

Output voltage 10.5 V ±0.5 V

Max. load FC101 25 mA

FC102 15 mA

Control card, 24 V DC output:

Max. load FC101 = 80 mA

FC102 = 200 mA

Surroundings:

Enclosure separate unit FC101 = IP54

FC102 = IP55

Vibration test separate unit 1.0 g

Max. relative humidity,

during operation 5% - 95%(non-condensing)

Maximum ambient temperature FC101 = 40 °C

FC102 = 45 °C (24h average)

Minimum ambient temperature

during full-scale operation 0 °C separate unit

Standard built-in ﬁeldbus communication:

Modbus RTU FC101 and FC102

BACnet embedded FC101 and FC102

N2 Metasys FC101 and FC102

FC Protocol FC101 and FC102

FLN Aapogee FC101 and FC102

Physical layer RS-485

Optional Fieldbus communication:

VLT

Proﬁbus DP V1 MCA 101 FC102

VLT

DeviceNet MCA 104 FC102

VLT

LonWorks MCA 108 FC102

VLT

BACnet MCA 109 FC102

VLT

ProﬁNet MCA 120 FC102

VLT

EtherNet/IP MCA 121 FC102

VLT

Modbus TCP MCA 122 FC102

VLT

BACnet/IP MCA 125 FC102

FC101 and FC102 frequency converters for plug fan GMPM -

Quick Guide

FläktGroup DC_10035GB_20180514_R0

Specifications are subject to change without further notice

4. SEPARATE FREQUENCY CONVERTER DIMENSIONS 5. SPECIFICATION FOR MOTOR

• Admissible environmental temperature: from -15 °C up to

+40 °C, with altitudes 1000 m above sea level

• Mounting: IM B3

• Drive operating voltage: 400 VAC

• Insulation class: “F”; temperature rise to class B

(TEFC execution)

• IP55 degree of protection for the whole range

• Reduced dimensions

6. INSTALLATION

Warning: Risk of electric shock

Motor terminals may still be Live if the impeller is

rotating, even when the main incoming supplied has

been isolated. Ensure the impeller is kept stationary

before opening and whilst the terminal box is open.

Frequency converter and motor shall be installed by a qualiﬁed

electrician with adequate knowledge how to install speed-con-

trolled drive systems (frequency inverters) and EMC safety.

All cabling must comply with national and local regulations on ca-

ble cross-sections and ambient temperature

FC101

Power

(kW)

Dimensions (mm) Weight

(kg)

Height Width Depth

Hole

ØD

A a B b

0.75-4 332 318.5 115 74 225 5.5 5.3

5.5-7.5 369 354 135 89 237 6.5 7.2

11-18.5 476 460 180 133 290 6.5 13.8

Protection class IP 54

FC102

Power

(kW)

Dimensions (mm) Weight

(kg)

Height Width Depth

Hole

ØD

A a B b

1.1.-4 420 401 200 171 175 6.5 9.7

5.5-7.5 420 402 242 215 200 6.5 13.5

11-15 480 454 242 210 260 9.0 23.0

Protection class IP 55

FC101 and FC102 frequency converters for plug fan GMPM -

Quick Guide

FläktGroup DC_10035GB_20180514_R0

Specifications are subject to change without further notice

7. CONNECTION DIAGRAM

AHU

SUPPLY

12 18 27 +10 V

55 55 01 02 03 04 05 06 61 68 6953

RELAY 1 RELAY 2 RS-485

Com P N

L2 L3

START/STOP

INTERLOCK

ALARM

RUNNING

INDICATION

PE U V W PE

PE min 10 mm2 or two wires

3x400 V AC

PM-MOTOR

FREQUENCY CONVERTER

AHU CONTROLLER

W2 U2 V2

U1 V1 W1

– +

CONTROL SIGNAL

0 - 10 V

FC101 and FC102 frequency converters for plug fan GMPM -

Quick Guide

FläktGroup DC_10035GB_20180514_R0

Specifications are subject to change without further notice

8. CABLING

8.1. SUPPLY CABLE

Mount mains supply to terminals L1, L2 and L3 and ground wires

to earth terminal and tighten.

SHORT CIRCUIT PROTECTION:

The frequency converter must be protected against short-circuit

to avoid electrical or ﬁre hazard. The fuses mentioned below are

recommended to use to protect service personnel and equipment

in case of an internal failure in the frequency converter. Frequency

converter provides full short circuit protection in case of a short

circuit on the motor output.

OVER CURRENT PROTECTION:

Provide overload protection to avoid ﬁre hazard due to overheat-

ing of the cables in the installation. The frequency converter is

equipped with an internal over-current protection that can be used

for upstream overload protection (UL-applications excluded). See

par. 4-18 Current Limit. Moreover, fuses or circuit breakers can

be used to provide the over-current protection in the installation.

Over-current protection must always be carried out according to

national regulations.

LEAKAGE CURRENT (>3,5 mA)

EN/IEC61800-5-1 (Power Drive System Product Standard) re-

quires special care if the leakage current exceeds 3,5mA. Earth

grounding must be reinforced in one of the

following ways:

• Earth ground wire of at least 10mm²

• Two separate earth ground wires both complying with the

dimensioning rules

ISOLATION SWITCH

All frequency converters may be used with an isolated input

source as well as with ground reference power lines.

8.2. RECOMMENDED FUSES ON THE SUPPLY SIDE

Power (kW) 0.55 0.75 1.1 1.5 2.2 3 4 5.5 7.5 11 15

3x380-480VAC

Rec. non UL type gG 10 10 10 10 16 16 16 25 25 50 50

See national/international regulations for selecting an applicable

fuse size.

8.3. MOTOR CABLE

Frequency converter is delivered with a 3.5 m motor cable for fan

sizes up to 050. For bigger fans the motor cable length is 4.5 m.

Should the cable be shortened or replaced with a longer one a

few rules must be followed. Motor cable must be of shielded type.

Shield should be grounded 360° at both ends of the cable. The

motor cable must not be longer than 10 meters to achieve EMC-

level EN 55011 Class B with standard FC101 and FC102 frequency

converters. Motor cable can be extended to 50 meters with op-

tional H1 EMC ﬁlter in FC102.

Motor is connected to star inside the motor. Phase wires are

connected to terminals U1, V1, W1. Terminal connectors are not

needed.

8.4. CONTROL CABLE

Control cable must be shielded. Keep control cable distance min.

200 mm from mains and motor cable.

FC101 and FC102 frequency converters for plug fan GMPM -

Quick Guide

FläktGroup DC_10035GB_20180514_R0

Specifications are subject to change without further notice

9. CONTROL SIGNALS

START/STOP

Fan is started with potential free switch connected between ter-

minals 12 and 18. There is +24 VDC in this circuit. AUTO-mode

should be selected from operation panel.

INTERLOCK

By opening interlock signal between terminals 12-27 the fan can

be stopped and then it is not possible to start from operating

panel manually or via bus. With this signal fan running can be in-

terlocked to circulating pump alarm or ventilation emergency stop.

This function can be activated by setting parameter 5-12 value to

“Coast inverse”.

SPEED REFERENCE

Speed can be controlled with 0…10V signal connected in termi-

nals 53(+) and 55(-).

RELAY OUTPUTS

Alarm signal is available in relay1 (terminals 01, 02 and 03).

Running indication is available in relay 2 (terminals 04, 05 and

06).

SINGLE SPEED OPERATION:

Set constant speed reference (Hz) in parameter 412. Only external

start signal is needed.

TWO SPEED OPERATION:

Lower speed reference (Hz) is set in parameter 412 and higher

speed reference (Hz) in parameter 311. Lower speed is activated

with start signal (terminals 12-18). Higher speed is activated by

closing terminals 12-29.

MODBUS RTU

Frequency converter can be controlled via Modbus RTU. RS-485

cable is connected to the terminals 68 (P), 69 (N) and 61 (COM). If

the frequency converter is the last unit in line, it should be termi-

nated by setting switch S801 in ON position. Modbus operation is

described in frequency converter operation instructions.

10. START UP AND FUNCTIONAL TESTING

After power up test check motor rotation if a separate frequency

converter is delivered:

Set frequency converter to Hand on mode from operation panel.

Motor will start to rotate. For changing the direction of rotation,

disconnect supply voltage and wait for power to discharge. Make

sure that the motor impeller is not rotating when making connec-

tions. Reverse the connection of any two of the three motor cables

on the motor or frequency converter side of the connection.

When direction of rotation is right set frequency converter to Auto

on mode. Then the frequency converter will follow control signals.

11. PARAMETERS

Frequency converter parameters are set at the factory providing

for optimal performance of fan and motor. This includes motor pa-

rameters, ramp times, starting and stopping methods and speed

limitations. Changing these parameters may result in unstable op-

eration or the motor will not start. Original parameter values can

be downloaded from operation panel in case of losing them:

• Go to parameter 0-50 LPC Copy

• Set parameter value to 2 (All from LCP)

• Wait until the copy is completed

Parameters are password protected. Changing motor parameters

may cause a motor failure. Password for main menu is 100 and

for quick menu 200.

FC101 and FC102 frequency converters for plug fan GMPM -

Quick Guide

FläktGroup DC_10035GB_20180514_R0

Specifications are subject to change without further notice

12. OPERATING PANEL FC101

Operating panel is standard in frequency converter FC101.

A. ALPHA NUMERIC DISPLAY

The LCD-display is back-lit with 2 alpha-numeric lines. All data is

displayed on the LCP.

Information can be read from the display.

1Parameter number and name.

2Parameter value.

Set-up number shows the active set-up and the edit setup.

If the same set-up acts as both active and edit set-up, only

that set-up number is shown (factory setting).

When active and edit set-up differ, both numbers are

shown in the display (Setup 12). The number ﬂashing,

indicates the edit set-up.

Motor direction is shown to the bottom left of the display

– indicated by a small arrow pointing either clockwise or

counterclockwise.

B. MENU KEY

Use the menu key to select between status, quick menu or

main menu.

5The triangle indicates if the LCP is in status, quick menu or

main menu.

C. NAVIGATION KEYS AND INDICATOR LIGHTS (LEDS)

6Com led: Flashes when bus communication is

communicating.

7Green LED/On: Control section is working.

8Yellow LED/Warn.: Indicates a warning.

9Flashing Red LED/Alarm: Indicates an alarm.

10 [Back]: For moving to the previous step or layer in the

navigation structure

[s] [▼] [ ]: For maneuvering between parameter

groups, parameters and within parameters.

Can also be used for setting local reference.

12 [OK]: For selecting a parameter and for accepting

changes to parameter settings.

D. OPERATION KEYS AND INDICATOR LIGHTS (LEDS)

[Hand On]: Starts the motor and enables control of the

frequency converter via the LCP.

NOTICE!

Terminal 27 Digital Input (5-12 Terminal 27 Digital Input) has

coast inverse as default setting. This means that [Hand

On] not starts the motor if there is no 24 V to terminal

27. Connect terminal 12 to terminal 27.

14 [Off/Reset]: Stops the motor (Off). If in alarm mode the

alarm will be reset.

15 [Auto On]: frequency converter is controlled either via

control terminals or serial communication.

Com.

Back

Alarm

Hand

Off

Reset

Auto

Warn.

1-20 Motor Power

[5] 0.37kW - 0.5 HP

Setup 1

Status Quick

Main

14 15

FC101 and FC102 frequency converters for plug fan GMPM -

Quick Guide

FläktGroup DC_10035GB_20180514_R0

Specifications are subject to change without further notice

13. OPERATING PANEL FC102

Operating panel is standard in frequency converter FC102.

A. DISPLAY AREA

The display area is activated when the frequency converter

receives power from mains voltage, a DC bus terminal, or an

external 24 V DC supply.

The information displayed on the LCP can be customized for user

application. Select options in the Quick Menu Q3-13 Display Settings.

Display Parameter number Default setting

10-20 Reference %

2 0-21 Motor current

3 0-22 Power [kW]

4 0-23 Frequency

5 0-24 kWh counter

Auto

on Reset

Hand

Status Quick

Main

Alarm

Log

Back

Cancel

Info

Status 1(1)

0.00 kW

0.0Hz

Alarm

Warn.

0.00 A

0.0 %

2605 kWh

18 19 20 21

Indicator Light Function

15 ON Green

The ON light activates when the frequency

converter receives power from mains volt-

age, a DC bus terminal, or an external 24

V supply.

16 WARN Yellow

When warning conditions are met, the

yellow WARN light comes on and text

appears in the display area identifying the

problem.

17 ALARM Red A fault condition causes the red alarm light

to ﬂash and an alarm text is displayed.

D. OPERATION KEYS AND RESET

Operation keys are located at the bottom of the LCP.

Key Function

18 Hand On

Starts the frequency converter in local control.

• An external stop signal by control input or

serial communication overrides the local hand on

9Off Stops the motor but does not remove power to

the frequency converter.

20 Auto On

Puts the system in remote operational mode.

• Responds to an external start command by con-

trol terminals or serial communication

21 Reset Resets the frequency converter manually after

a fault has been cleared.

C. NAVIGATION KEYS AND INDICATOR LIGHTS (LEDS)

Navigation keys are used for programming functions and moving

the display cursor. The navigation keys also provide speed control

in local (hand) operation. There are also 3 frequency converter

status indicator lights in this area.

Key Function

10 Back Reverts to the previous step or list in the menu

structure.

11 Cancel Cancels the last change or command as long as

the display mode has not changed.

12 Info Press for a deﬁnition of the function being dis-

played.

13 Navigation

Keys

Use the 4 navigation keys to move between items

in the menu.

14 OK Use to access parameter groups or to enable a

choice.

B. DISPLAY MENU KEYS

Menu keys are used for menu access for parameter set-up,

toggling through status display modes during normal

operation, and viewing fault log data.

Key Function

6Status Shows operational information.

7Quick Menu

Allows access to programming parameters for

initial set-up instructions and many detailed appli-

cation instructions.

8Main Menu Allows access to all programming parameters.

9 Alarm Log Displays a list of current warnings, the last 10

alarms, and the maintenance log.

FC101 and FC102 frequency converters for plug fan GMPM -

Quick Guide

FläktGroup DC_10035GB_20180514_R0

Specifications are subject to change without further notice

14. ALARMS AND WARNINGS

If alarm or warning messages appear, consult the frequency con-

verter operating manual for fault messages and troubleshooting.

Warning! Frequency converter tries to restart the motor after alarm so

the fan may start automatically.

PROTECTION AND FEATURES:

• Electronic thermal motor protection against overload.

• Temperature monitoring of the heatsink ensures that the

frequency converter trips if the temperature is too high.

• The frequency converter is protected against short-circuits on

motor terminals U, V, W.

• If a mains phase is missing, the frequency converter trips or

issues a warning (depending on the load).

• Monitoring of the intermediate circuit voltage ensures that the

frequency converter trips if the intermediate circuit voltage is

too low or too high.

• The frequency converter is protected against earth faults on

motor terminals U, V, W.

• If the frequency converter can’t ﬁnd rotor position, Locked Ro-

tor alarm is generated.

• Motor is stopped if motor back voltage is too high.

• Motor is stopped if 24V supply is too low.

• Motor is stopped if motor phase is missing.

• Motor is stopped if inverter overloaded too long.

FG_DC-10053GB_

Frequency controllers FC101 and FC102

WWW.FLAKTGROUP.FI GMPM FC101-FC102

» Learn more on www.ﬂaktgroup.com

or contact one of our ofﬁces

A HISTORY OF INNOVATION

AND RELIABILITY

With more than a century of accumulated industry experience, FläktGroup is in

a unique position to deliver energy efﬁcient components and solutions for inte-

grated performance, reliability and quality. With modern manufacturing techno-

logies, precise deliveries and technical support, FläktGroup is your partner –

fulﬁlling and surpassing industry standards and certiﬁcations.

FläktGroup CentriFlow 3D GMPM FC101_FC102 Quick start guide

FläktGroup CentriFlow 3D GMPM FC101_FC102 Quick start guide

FläktGroup CentriFlow 3D GMPM FC101_FC102 Quick start guide

Related papers

Other documents