ASSEMBLY AND INSTALLATION
INSTRUCTIONS
NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. READ AND SAVE THESE INSTRUCTIONS.
T0220
Hardware Package (included):
WARNING:
TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF
POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.
151118
Mounting Screw (B)
Green Grounding Screw (C)
Wire Nut (D)
House Grounding Wire
Fixture Grounding Wire
Outlet Box
Fixture Wire
Threaded Pipe(E)
Mounting Strap (A)
Hex Nut (F)
Washer (G)
Ceiling Pan
Glass Shade
Short Threaded Pipe (L)
Hex Nut (I)
Metal Pad (J)
Rubber Pad (K)
End Cap(H)
Metal Frame
Ball Nut
Finial (M)
Set Screw
Socket
Mounting Screw (B)
Threaded Pipe (E)
Green Grounding
Screw (C)
Wire Nut (D)
Mounting Strap (A)
Hex Nut (F)
Washer(G)
End Cap(H)
Hex Nut (I)
Turn off the power at fuse or circuit box.
Installation Steps
1. Attach the threaded pipe to the mounting strap,
and then secure it with a washer and a hex nut.
2. Attach the mounting strap to the outlet box using
two mounting screws.
3. Unscrew two ball nuts from ceiling pan.
4. Pull out the wires and grounding wire from the outlet
box. Make wire connections using the wire nuts.
as follows:
---Connect the hot wire (usually black insulation)
from the fixture to the black wire from the power
source.
---Connect the neutral wire (usually white insulation)
from the fixture to the white wire from the power
source.
---Attach the fixture grounding wire (usually green
insulation or bare wire) to the mounting strap with
the green grounding screw, and then connect it to
the house grounding wire with the wire nut.
Carefully put the wires back into the outlet box.
5. Attach the ceiling pan to the mounting strap by inserting threaded pipe into the center hole of the ceiling pan,
and then screw the end cap to secure ceiling pan.
6. Install bulbs (not included). Check relamping label at socket area or packaging for maximum allowed wattage.
7. Lay the glass shade into metal frame carefully.
Bulb Type A Max.60W
(not included)
Short Threaded pipe (L)
Metal Pad (J) Rubber Pad (K)
Finial (M)
A
B
151118
Mounting Screw (B)
Threaded Pipe (E)
Green Grounding
Screw (C)
Wire Nut (D)
Mounting Strap (A)
Hex Nut (F)
Washer(G)
End Cap(H)
Turn on the power at fuse or circuit box.
8. Slip the short threaded pipe down through the holes of glass shade and the metal frame, secure one end of the short
threaded pipe with the finial, the other end with the rubber pad, the metal pad and the hex nut.
NOTE:Please don’t over tighten, breakage could occur.
9. Attach the metal frame up to the ceiling pan by inserting two set screws, and then secure them with two ball nuts.
The following parts are available for re-order if damaged or missing.
Spare Parts List:
Assembly Kit
5498MM (1 SET)
Glass Shade
9802C(1 PC)
Ball Nut
5504BB (2 PCS)
A: 15" B: 5-3/4"
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Cascadia W0046 Installation guide
-
-
-
-
-
-
-
-
-
Other documents
-
Generation Lighting SF240BS Operating instructions
-
Generation Lighting OL8513ORB Installation guide
-
C Cattleya CA2241-2W Operating instructions
-
-
Filament Design CLI-TL5004840 Installation guide
-
Filament Design CLI-TL5003157 Installation guide
-
-
Generation Lighting SF251BS Installation guide
-
Design House 578500 Installation guide
-
Generation Lighting OL5413GBZ Installation guide
