Cascadia C0078 Installation guide

Cascadia
Brand
Cascadia
Model
C0078
Type
Installation guide

Cascadia C0078 is a lighting fixture designed for indoor use. It requires assembly before installation. The fixture includes a mounting strap, short screws, a green grounding screw, long screws, wire nuts, a lock nut, ball nut, canopy, glass shade, frame, bolt nuts, and a socket. The fixture is compatible with Type A bulbs with a maximum wattage of 100W (bulb not included). To install the fixture, turn off the power at the fuse or circuit box, connect the wires using wire nuts, attach the canopy to the mounting strap, attach the glass shade and frame, and install the bulb.

Cascadia C0078 is a lighting fixture designed for indoor use. It requires assembly before installation. The fixture includes a mounting strap, short screws, a green grounding screw, long screws, wire nuts, a lock nut, ball nut, canopy, glass shade, frame, bolt nuts, and a socket. The fixture is compatible with Type A bulbs with a maximum wattage of 100W (bulb not included). To install the fixture, turn off the power at the fuse or circuit box, connect the wires using wire nuts, attach the canopy to the mounting strap, attach the glass shade and frame, and install the bulb.

ASSEMBLY AND INSTALLATION
INSTRUCTIONS
NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. READ AND SAVE THESE INSTRUCTIONS.
C0078
WARNING:
TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF
POWER WHILE INSTALLING OR SERVICING THIS FIXTURE.
Turn off the power at fuse or circuit box.
141119
Page 1
Mounting Strap (A)
Short Screw (B)
Green Grounding
Screw (C)
Lock Nut (F)
Wire Nut (E)
Hardware Package (included):
Assembly Instructions:
1. Thread two long screws to the mounting strap, and secure with
two lock nuts. Adjust the length of the screws if necessary.
2. Attach the mounting strap to the outlet box using two short
screws.
3. Pull out the source wires from the outlet box. Make wire
connections using wire nuts as follows:
---Connect the hot wire (usually black insulation) from the
fixture to the black wire from the power source.
---Connect the neutral wire (usually white insulation) from the
fixture to the white wire from the power source.
---Attach the fixture grounding wire (usually bare wire) to the
mounting strap with the green grounding screw. Then
connect it to the house grounding wire with a wire nut. If your
outlet box does not have a house grounding wire, then wrap
the fixture grounding wire around the green grounding screw.
Carefully put the wires back into the outlet box.
4. Attach the canopy to the mounting strap: insert the long screws
through the two holes, and secure with two ball nuts.
CAUTION: With silicone caulking compound, caulk completely
around where back of canopy meets with the ceiling surface to
prevent water from seeping into the outlet box.
5. Attach the glass shade and frame onto the fixture, secure them with bolt nuts.
6. Install bulb (not included). See relamping label at socket area or packaging for maximum allowed wattage.
Turn on the power at fuse or circuit box.
Long Screw (D)
Ball Nut (G)
Bolt Nut
Socket
Fixture
Canopy
Outlet Box
House Grounding Wire
Wire Nut (E)
Short Screw (B)
Mounting Strap (A)
Green Grounding Screw (C)
Lock Nut (F)
Long Screw (D)
Bulb Type A Max.100W
(not included)
Glass Shade
Ball Nut (G)
Frame
Assembly Kit
(5226MM)
(1 SET)
The following parts are available for re-order if damaged or missing.
141119
Page 2
A: 13-1/2"
B: 11-1/4"
Mounting Strap (A)
Short Screw (B)
Green Grounding
Screw (C)
Wire Nut (E)
Long Screw (D)
Lock Nut (F)
Ball Nut (G)
Glass Shade
(9679CS)
(1 PC)
Bolt Nut
(5229BB)
(4 PCS)
  • Page 1 1
  • Page 2 2

Cascadia C0078 Installation guide

Cascadia
Brand
Cascadia
Model
C0078
Type
Installation guide

Cascadia C0078 is a lighting fixture designed for indoor use. It requires assembly before installation. The fixture includes a mounting strap, short screws, a green grounding screw, long screws, wire nuts, a lock nut, ball nut, canopy, glass shade, frame, bolt nuts, and a socket. The fixture is compatible with Type A bulbs with a maximum wattage of 100W (bulb not included). To install the fixture, turn off the power at the fuse or circuit box, connect the wires using wire nuts, attach the canopy to the mounting strap, attach the glass shade and frame, and install the bulb.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents