Edgewater Networks EdgeConnect 2402LFPoE Quick start guide

Brand: Edgewater Networks

Model: EdgeConnect 2402LFPoE

Type: Quick start guide

EdgeConnect 2402LFPoE

Managed Ethernet Switch

Quick Start Guide

Version 1.0

Before You Start

Thank you for the purchase of your EdgeConnect 2402LFPoE Managed

Ethernet Switch.

Please read this guide thoroughly as it describes how to initially connect

to your 2402 Switch. Please refer to the User Manual for instructions on

the physical installation and power requirements of the EdgeConnect

2402LFPoE Managed Switch. Additional information and help files

regarding the features of the 2402LFPoE Switch can be found by

accessing the “Support” link once connected to the appliance via your

web browser.

Requirements for Installation

• A computer with a web browser such as Microsoft Internet Explorer or

Netscape Navigator or any other browser of your choice, an available

Ethernet port, and an optional terminal emulation program if

connecting through the serial port.

• At least one Ethernet cable.

• An optional null-modem cable if connection through the console is

desired.

• If uplink and downlink fiber connection is required, then 2 fiber cables

along with 2 Mini-GBIC SPF connectors

• If uplink and downlink Ethernet connection is required then, 2 Ethernet

cables.

Page 1 of 6

Instructions

Step 1 − Connecting the Cables

Front View

Back View

1. If an uplink connection to the WAN or another switch is desired, then connect the

10/100/1000 Mbps combo port 26 (denoted by “C” in the above figure) to a switch or

router through an Ethernet cable or through a fiber cable using Mini-GBIC SFP

connector.

2. Port 25 (denoted by “B” in the above figure) is an out of band 10/100/1000 Mbps

downlink port used for management purposes among other things.

3. Connect one end of an Ethernet cable to port 24 (denoted by “A” in the above figure) of

the switch. Connect the other end to the Ethernet port on the computer that will be used

to configure the switch.

4. Plug the 3-prong grounded male plug into an AC outlet (100-240V, 47 to 63 HZ) and the

other end (3-pin Shroud male connector) into the power receptacle on 2402LFPoE

denoted by “E” in the above figure.

Page 2 of 6

Step 2 − Configuring 2402LFPoE through GUI

1. The EdgeConnect 2402LFPoE comes preconfigured with 192.168.1.254 local LAN

address with a subnet mask of 255.255.255.0. Configure the IP address of the Ethernet

adapter of the computer connected to 2402LFPoE’s port 24 to any address other than

192.168.1.1 in the same subnet mask, for example 192.168.1.10.

2. Launch a web browser on the PC and enter the following URL:

http://192.168.1.254 and

press Enter.

3. The following initial 2402 POE Switch main configuration menu should appears:

4. Enter “admin” in the “User name” and “Password” fields and click on the “OK” button.

5. The web page shown in the figure below should appear next.

Page 3 of 6

6. Continue configuring the switch using the “Configuration Menu” on the left side of the

web page and by referring to the user manual of the device.

Configuring 2404PoE through the console port

1. Connect one end of a null-modem cable to the serial port of the computer and the other

end to the console port of 2404PoE.

2. Configure the terminal emulation program to use:

a. Data bits: 8

b. Parity: none

c. Stop bit: 1

d. Flow control: none

e. Baud rate: 9600

3. Press the return key and the following text should appear:

Page 4 of 6

Please visit our website at www.edgewaternetworks.com or contact the Edgewater Technical

Assistance Center at 408.351.7255 for additional information or assistance.

Edgewater Networks, Inc.

2730 San Tomas Expressway

Suite 200

Santa Clara, CA 95051

Phone: (408) 351-7200

[email protected]

Converged Networking. Simplified.

Page 5 of 6

Edgewater Networks EdgeConnect 2402LFPoE Quick start guide

Edgewater Networks EdgeConnect 2402LFPoE Quick start guide

Edgewater Networks EdgeConnect 2402LFPoE Quick start guide

Related papers

Other documents