© 2018
Order #XXXXX
Plan View
Perspective View
10’
10’
Scale: 16
VK-1318 Display
SETUP INSTRUCTIONS
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
© 2018
Order #XXXXX
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all setscrews
and locks during disassembly
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information
© 2018
Crate 1 of 1
Order #XXXXX
Reflection
Panel &
Infills
Assembled
End Panel
Assembled
[8] & [2]
Literature
Holders
Lights
Setup
Hardware
9
(Qty. 4)
Strip Lights
Foot
Plates
4 5 3
Level 1 Level 2 Level 3 Level 4
Interior of Setup Hardware Box
Crate Packing
© 2018
Step 1 of 2
Order #XXXXX
4
99
9
Infill
Infill
9
7
5
3
1
6
82
Item
1
2
3
4
5
6
7
8
9
Qty.
1
1
1
1
1
1
1
1
4
Description
Foot Plate
96” Q914 Vertical Extrusion
96” Q914 Vertical Extrusion
87” Q914 Horizontal Extrusion
87” Q914 Horizontal Extrusion
96” Z45 Vertical Extrusion
96” S40 Vertical Extrusion
96” GS210 Vertical Extrusion
14” Z45 Horizontal Extrusion
Steps:
1) Attach foot plate to vertical [3].
See Foot Plate Attachment detail.
2) Attach horizontals [4] and [5] between verticals [2] and [3].
3) Attach horizontals [9] between verticals [6] [7] and [8],
with infills between.
4) Attach vertical [8] to vertical [2], using pressure screws.
See Pressure Screw detail.
Completed Assembly
*
*
*
Bolt
Foot Plate
V4 Connectors
Slide V4 connectors into extrusion
then attach foot plate using bolts.
Vertical Extrusion
Foot Plate Attachment
*
Velcro on
Back/Bottom edge
of Top horizontal
Velcro on
Back/Top edge
of Bottom horizontal
Velcro on Back/Inside
edges of vertical
Velcro on Back/Inside
edges of vertical
*
Pressure
Screw
Slide pressure screw between
grooves of extrusions. Tighten
set screw to secure.
Pressure Screw
Pressure
Screw
VK-1318 Assembly
© 2018
Step 2 of 2
Order #XXXXX
Monitor
Mount
Reflection
Panel
Velcro for Strip
Lights
**
*
**
Completed Assembly
*
Slide light onto clip then lock clip
into groove of horizontal extrusion.
Light Connection
Clip
Light
Light
Horizontal Extrusion
Clip
Monitor Mount
V4 Connectors
*
Slide connectors into groove
of extrusion. Tighten set screws
to secure connectors in place.
Attach monitor mount back
plate to extrusion, using bolts.
Bolts
Monitor
Mount
Connector
Literature Holder Attachment
Locks
Literature
Holder
Attach angled end of connector to
literature holder. Attach flat end of
connector to vertical extrusion.
Tighten locks to secure.
*
Steps:
1) Attach literature holders to vertical [7]. See Literature Holder Attachment detail.
2) Attach monitor mount to vertical [3]. See Monitor Mount detail.
3) Connect lights to horizontal [5]. See Light Connection detail.
4) Connect strip lights to Velcro on center of reflection panel then attach reflection
panel to Velcro on verticals [6] and [8].
5) Connect graphic to Velcro on back of extrusions [2] [3] [4] and [5].
7
5
6
4
3
2
8
VK-1318 Attachments
/