Classic Exhibits VK-1324 Setup Instructions

Classic Exhibits
Brand
Classic Exhibits
Model
VK-1324
Type
Setup Instructions
© 2015
www.classicexhibits.com
Order #XXXXX -
Perspective View
Plan View
10’
10’
VK-1324
SETUP INSTRUCTIONS
If you would like to tell us about your experience with your setup instructions please email us at
[email protected]
© 2015
www.classicexhibits.com
Order #XXXXX -
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all setscrews
and locks during disassembly
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information
© 2015
www.classicexhibits.com
Order #XXXXX -
Step 1 of 6
Backwall Assembly
1
3
4
5
Front Infill
A
Front Infill
BLarge Infill
B
Large Infill
A
Small Infill
B
Small Infill
A
7
7
8
9
9A 10
12
11
9B
8A
6
6A
4A
4B
2
2B
2A
Item
1
2
2A/2B
3
4/4A/4B
5
6/6A
Qty.
1
1
1/1
1
1/1/1
1
1/1
Description
94”h Q914 Vertical Extrusion w/ Door Hinges
36”w Z45 Horizontal Extrusion
36”w Z45 Horizontal Extrusion w/ Velcro
94”h Q914 Vertical Extrusion
23”w Z45 Horizontal Extrusion
94”h Q914 Vertical Extrusion
36”w Z45 Horizontal Extrusion w/ Velcro
Item
7
8/8A
9/9A
9B
10
11/11A/11B
12
Qty.
1
1/1
1/1
1
1
1/1/1
1
Description
94”h Q914 Vertical Extrusion
23”w Z45 Horizontal Extrusion w/ Velcro
9”w Q914 Horizontal Extrusion
9”w Z45 Horizontal Extrusion
94”h Q914 Vertical Extrusion
23”w Z45 Horizontal Extrusion
94”h Q914 Vertical Extrusion
Steps:
1) Connect horizontals [2], [2A], & [2B] between verticals [1] & [3].
2) Attach horizontals [8] & [8A] between verticals [1] & [7].
3) Connect horizonals [6] & [6A] between verticals [5] & [7].
4) Attach horizontal [4] between verticals [3] & [5]; insert Front Infill A.
5) Connect horizontal [4A] on top of Front Infill A; insert Front Infill B;
secure with horizontal [4B].
6) Attach horizontal [9] between verticals [7] & [10]; insert Small Infill A;
secure with horizontal [9B].
7) Insert Small Infill B between verticals [7] & [10]; secure with
horizontal [9A].
8) Attach horizontal [11] between verticals [10] & [12].
9) Insert Large Infill A between verticals [10] & [12]; secure with horizontal
[11A]; insert Large Infill B; secure with horizontal [11B].
10) Install Assembled Closet Door. See Door Attachment detail.
11A
11B
Assembled
Closet Door
Door
Hinge
Hinge
Slide pin into
hinge attached
to vertical.
Slide door
hinge over pin.
Door Attachment
© 2015
www.classicexhibits.com
Order #XXXXX -
Step 2 of 6
Ceiling Assembly
Infill
Infill
Infill
13A
13
14
14
15
16
Item
13/13A
14
15
16
Qty.
1/1
2
1
1
Description
73.085”w S44 Horizontal Extrusion
15.5”w S44 Extrusion
15.5”w Z140 Extrusion
15.5”w Z140 Extrusion w/ Puck Light
Steps:
1) Attach extrusions [14] to horizontal [13].
2) Insert infills and extrusions [15] & [16]; secure with horizontal [13A]
When Assembled
© 2015
www.classicexhibits.com
Order #XXXXX -
Step 3 of 6
Attachments
3
9
9
9
9
9
9
3
10
1
Graphic WingGraphic Wing
Graphic Wing Graphic Wing
Graphic WingGraphic Wing
10
Item
17
Qty.
9
Description
Shelf Support Horizontal Extrusion
Steps:
1) Attach shelves to verticals [3] & [10]. See Shelf Attachment detail.
2) Connect Graphic Wings to installed A10 Clamps on verticals [1], [3], & [12].
3) Install Light on top of vertical [10]. See Light Attachment detail.
Light Connection
Attach lights to
backwall where
desired and
tighten in place.
*
Shelf Attachment
Insert lock into groove of vertical
extrusion and tighten setscrew.
*
Lock
Setscrew
Back of Shelf
Setscrew will face
outward for ease
of assembly
*
*
*
*
*
*
*
© 2015
www.classicexhibits.com
Order #XXXXX -
Step 4 of 6
Attachments Cont’d
Graphic Header
Steps:
1) Attach monitor mounts to verticals [2] & [12].
See Monitor Mount Attachment detail.
2) Connect Graphic Header to front verticals [2] & [3].
NOTE: Will attach using velcro.
Monitor Mount Attachment
Attach back plate to connectors
using screws provided.
Attach top plate and tighten
setscrews to secure.
Slide connectors into groove
of vertical extrusion.
Tighten setscrew to secure.
Setscrews
*
**
© 2015
www.classicexhibits.com
Order #XXXXX -
Step 5 of 6
Backwall Pedestals
Item
A
Qty.
2
Description
3” Horizontal Extrusion
Steps:
1) Screw assembled pedastal to Q914 vertical with screwcaps.
2) Attach counter top support [A] to backwall verticals [2,4,20].
3) Attach counter top to front horizontal and support [A] using screws.
4) Attach literature pockets to Velcro on sides of pedestal as shown.
Attach pedestal to
mounting connectors
in backwall with
screwcaps.
*
A
*
*
*
*
*
Attach literature
pockets with Velcro
to sides of pedestal.
Counter Top
*Literature Pocket Attachment Detail
Counter Top
Counter Top Support
Flat
Head Bolt
V2 Connector
Slide V2 connector into groove of shelf
support. Bolt through hole of shelf into
threaded hole of V2 connector. Twist Bolt
to secure counter top in place.
Counter Top Attachment Detail
*
© 2015
www.classicexhibits.com
Order #XXXXX -
Step 6 of 6
Freestanding Pedestal
Setup Instructions:
1) Attach counter top to front horizontal using screws as shown in detail.
2) Attach literature pockets to Velcro on sides of pedestal as shown.
Pedestal Attachment
Counter Top
Counter Top Support
Flat
Head Bolt
V2 Connector
Slide V2 connector into groove of shelf
support. Bolt through hole of shelf into
threaded hole of V2 connector. Twist Bolt
to secure counter top in place.
Counter Top Attachment Detail
*
*
Attach literature
pockets with Velcro
to sides of pedestal.
Counter
Top
*
*Literature Pocket Attachment Detail
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Classic Exhibits VK-1324 Setup Instructions

Classic Exhibits
Brand
Classic Exhibits
Model
VK-1324
Type
Setup Instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents