Bauknecht DBR 6990/IN Program Chart

Brand: Bauknecht

Model: DBR 6990/IN

Category: Cooker hoods

Type: Program Chart

This manual is also suitable for

DBR 6990/IN/PT

The Bauknecht DBR 6990/IN/PT is a stylish and powerful range hood that will make a great addition to your kitchen. With its sleek design and high-quality construction, this hood is sure to impress. It features a powerful motor that can quickly and efficiently remove smoke, grease, and odors from the air, leaving your kitchen smelling fresh and clean. The hood also has a built-in light that provides ample illumination for your cooking surface. With its easy-to-use controls and multiple speed settings, the Bauknecht DBR 6990/IN/PT is the perfect choice for any home chef.

5019 418 33085

INSTALLATIONSANLEITUNGEN

Mindestabstand über der Kochfläche: 50 cm bei Elektroplatten, 65 cm bei Gasmulden oder gemischt

betriebenen Kochfeldern. Schreiben die Installationsanweisungen des Gaskochfelds einen größeren

Abstand vor, ist dieser natürlich zu beachten. Folgen Sie bei der Installation der Nummerierung

(123.....). Schließen Sie das Gerät erst nach seiner kompletten Installation an das Stromnetz an.

Achtung! Kontrollieren Sie, ob das Abluftrohr und die Befestigungsschellen mitgeliefert wurden.

Andernfalls sind sie separat zu beziehen.

Aufgrund des schweren Gewichtes sind mindestens zwei oder noch mehr Personen zur Beförderung

und Installation der Abzugshaube erforderlich.

INSTALLATION DATA SHEET

Minimum height above cooker: 50 cm for electric cookers, 65 cm for gas or mixed cookers. If the

installation instructions for a gas cooker specify a greater distance, then this distance must be

observed. To install, follow steps (123.....). Do not connect the hood to the electrical power

supply until installation is completed. Warning! Check whether the exhaust pipe and clamps are

provided. If not, they must be purchased separately.

Excessively heavy product; hood handling and installation must be carried out by two or more

persons.

FICHE D'INSTALLATION

Distance minimale par rapport à la cuisinière : 50 cm minimum dans le cas d'une cuisinière électrique,

65 cm dans le cas d'une cuisinière à gaz ou mixte. Si les instructions d'installation du dispositif de

cuisson à gaz indiquent une distance supérieure, il est nécessaire de la respecter. Pour le montage,

suivez la numérotation (123.....). Ne branchez pas l'appareil tant que l'installation n'est pas

terminée. Attention ! Vérifiez si le conduit d'évacuation et les colliers de fixation sont fournis avec

l'appareil. Dans le cas contraire, les acheter.

Appareil excessivement lourd ; la manutention et l'installation de la hotte doivent être effectuées par

deux personnes ou plus.

INSTALLATIEKAART

Minimumafstand tot het kooktoestel: 50 cm bij elektrische kooktoestellen, 65 cm bij kooktoestellen

op gas of gemengd. Als de installatie-instructies van het kooktoestel op gas een grotere afstand

aangeven, moet hiermee rekening gehouden worden. Volg voor de montage de nummering

(123.....). Geef het apparaat geen stroom totdat de installatie geheel voltooid is. Let op!

Controleer of de afvoerpijp en de klembanden bijgeleverd zijn. Zo niet, dan moeten ze apart worden

aangeschaft.

Aangezien dit apparaat zwaar is, dient het door minstens twee of meer personen verplaatst en

geïnstalleerd te worden.

5019 418 33085

FICHA DE INSTALACIÓN

Distancia mínima desde los quemadores: 50 cm en caso de cocinas eléctricas y 65 cm en caso de

cocinas a gas o mixtas. Si en las instrucciones de instalación de la placa de cocina a gas se especifica

una distancia mayor respecto a la indicada, es necesario tenerlo en cuenta. Para el montaje, siga la

numeración (123...). No conecte el aparato a la corriente eléctrica hasta que la instalación esté

completamente finalizada. ¡Atención! Compruebe si el tubo de descarga y las abrazaderas de fijación

se suministran de serie. En caso contrario, tiene que comprarlos por separado.

Producto con peso excesivo; la campana extractora ha de ser transportada e instalada por dos o más

personas.

FICHA DE INSTALAÇÃO

Distância mínima dos fogões: 50 cm no caso de fogões eléctricos, 65 cm no caso de fogões a gás ou

mistos. Respeite as instruções de instalação do dispositivo de cozedura a gás se estas especificarem

uma distância superior à indicada. Para a montagem siga a numeração (123.....). Não ligue o

aparelho à corrente eléctrica enquanto a instalação não estiver concluída. Atenção! Verifique se o

tubo de descarga e as braçadeiras de fixação foram fornecidos com o aparelho. Caso contrário,

deverá adquiri-los à parte.

Produto com peso excessivo. A movimentação e a instalação do exaustor devem ser feitas por pelo

menos duas ou mais pessoas.

SCHEDA INSTALLAZIONE

Distanza minima dai fuochi: 50 cm in caso di cucine elettriche, 65 cm in caso di cucine a gas o miste.

Se le istruzioni di installazione del dispositivo di cottura a gas specificano una distanza maggiore

rispetto a quella specificata, bisogna tenerne conto. Per il montaggio seguire la numerazione

(123.....). Non dare corrente all’apparecchio finché l’installazione non è totalmente completata.

Attenzione! Verificare se il tubo di scarico e le fascette di fissaggio sono forniti a corredo. In caso

contrario, vanno acquistati a parte.

Prodotto dal peso eccessivo, la movimentazione e installazione della cappa deve essere fatta da

almeno due o più persone.

ΚΑΡΤΕΛΑ ΕΓΚΑΤΑΣΤΑΣΗΣ

Ελάχιστη απόσταση από τις εστίες: 50 cm σε περίπτωση ηλεκτρικών εστιών και 65 cm σε

περίπτωση εστιών αερίου ή µικτού τύπου. Εάν οι οδηγίες εγκατάστασης της εστίας αερίου

συνιστούν µεγαλύτερη απόσταση, σε σχέση µε εκείνη που έχει οριστεί, εφαρµόστε τις σχετικές

οδηγίες. Για την τοποθέτηση ακολουθήστε την αρίθµηση (123.....). Μην τροφοδοτείτε µε

ηλεκτρικό ρεύµα τη συσκευή πριν την ολοκλήρωση της εγκατάστασης. Προσοχή! Βεβαιωθείτε

ότι ο σωλήνας απαγωγής και τα κολάρα στερέωσης διατίθενται µε τον εξοπλισµό. Σε αντίθετη

περίπτωση πρέπει να τα προµηθευτείτε χωριστά.

Προϊόν µε µεγάλο βάρος. Η µετακίνηση και η εγκατάσταση του απορροφητήρα πρέπει να γίνει

τουλάχιστον από δύο ή περισσότερους

ανθρώπους.

5019 418 33085

4-13

17a

2 x

2,9x6,5

17b

2 x 3,5x9,5

5019 418 33085

INSTALLATION - ASSEMBLY INSTRUCTIONS

Remove the perimeter extraction panel and the grease filter/s (see the maintenance instructions for how to do this).

• Mark a line on the wall right up to the ceiling, corresponding to the centre-line of the hood (1).

• Apply the drilling template to the wall: the vertical centre-line on the drilling template must correspond with the centre-line

drawn on the wall. The template's bottom edge must be aligned with the bottom edge of the hood (2).

• Place the support bracket on the hole diagram so that it matches the dashed rectangle, mark the two external holes and

drill. Remove the drilling template, insert 2 wall plugs in the holes and fix the hood support bracket (3) in place with two

5x45 mm screws.

• Hang the hood on the mounting bracket (4). Adjust the gap (5) and the horizontal alignment (6) of the hood.

• Mark 2 holes for final fixing of the hood (7).

• Remove the hood from the bracket (8). Drill the holes (9. - Ø 8 mm - see step 7). Insert two wall plugs (10).

• Apply the flue mounting bracket G to the wall against the ceiling. (Align the small slot in the bracket with the centre-line

drawn on the wall. See step 1 Fix the bracket in place with two wall plugs (Ø 8 mm) (11) and 2 screws (12).

• Hang the hood on the bottom mounting bracket. (13) Fix the hood to the wall with two 5 x 45 mm screws (14)

(ABSOLUTELY NECESSARY). Plug the two holes.

• Connect an exhaust pipe to the collar B. The pipe ducts directly to the outside (15) (extractor version) or towards the

deflector (filter version). Fix the deflector (F) to the flue support bracket G, if it is not already fitted. Fx the collar

(bayonette coupling) to the deflector F using a screw.

• Carry out the electrical connection (16).

• Apply the flues and fix them with 2 screws (17a) to the flue support G (17b).

• Slide the bottom section of the flue in the special seat above the hood to completely cover the extraction unit (18).

Refit the grease filter and the perimeter extraction panel, connect the hood to the power supply, and wait for the control

electronics to carry out the calibration necessary for proper operation of the control panel (all pushbuttons will flash during

calibration)

1. Control panel.

2. Grease filter.

3. Halogen bulbs.

4. Steam deflector.

5. Telescopic flue.

6. Extraction panel.

IF NL EGB PD GR

5019 418 33085

PRODUCT DESCRIPTION SHEET

Control panel

To select the hood functions you only have to touch the controls lightly.

They are screen printed at the centre of the glass on the front of the hood.

In the event of any malfunction, before contacting the service department, try disconnecting the appliance from the power

supply for at least 5 sec. by removing the plug, then re-connecting the plug and waiting approximately 15 seconds (the time

required to perform recalibration of the controls) before trying again.

If the fault persists, contact an authorised service centre.

Motor ON/OFF switch (stand by) - Electronics OFF

MOTOR OFF

Press briefly to turn the motor off.

ELECTRONICS ON/OFF

Press for more than 3 seconds to disable the hood control electronics.

Note: it is still possible to turn the lights on and off.

This function may be useful when cleaning the product.

To turn the electronics back on again, simply repeat the operation.

Low speed selection button (suction power) and Timer ON/OFF button.

After selecting the speed, press again for more than 2 seconds to set the timer (the button starts to flash).

The hood will turn off after 20 minutes.

Medium speed selection button (suction power) and Timer ON/OFF button.

After selecting the speed, press again for more than 2 seconds to set the timer (the button starts to flash).

The hood will turn off after 15 minutes.

High speed selection button (suction power) and Timer ON/OFF button.

After selecting the speed, press again for more than 2 seconds to set the timer (the button starts to flash).

The hood will turn off after 10 minutes.

Intensive speed selection button (suction power) - duration 5 minutes - and Timer ON/OFF button.

After selecting the speed, press again for more than 2 seconds to set the timer (the button starts to flash).

The hood will turn off after 5 minutes.

Light ON/OFF button

ABCDEF

IF NL EGB PD GR

5019 418 33085

Maintenance

ALWAYS disconnect the hood from the mains before performing

maintenance.

Clean the perimeter extraction panel as often as the grease filter,

using a cloth and a mild liquid detergent.

Never use abrasive substances.

Wash the grease filter and the carbon filter in a dishwasher once a

month, at the highest possible temperature, using normal

dishwasher detergent.

It is recommended to wash the filters on the their own.

After washing, reactivate the carbon filter by drying it in the oven

at 100° C for 10 minutes. Fit a new carbon filter every 3 years.

Remove the perimeter extraction panel - Fig.1:

Warning! Hold the panel with both hands when you remove it

or replace it, to prevent it from falling and causing damage or

injury.

Pull the panel (FRONT SIDE) firmly downwards and disconnect it

from the rear hinges.

Fitting: The panel must be hooked up at the rear and snap-fitted

at the front into the hinges provided for this purpose on the

surface of the hood.

Warning! Always check to ensure that the panel is firmly

fixed in place.

Remove the grease filters - Fig. 1: to do so, (after removing the

perimeter extraction panel) push the spring release handle

backwards (f1) then remove the filter downwards (f2).

Fitting: reverse the above procedure.

Replacing bulbs - Fig. 1:

1. Use a small screwdriver or any other suitable tool to prise off

(m) the lamp cover (p).

2. Remove the burnt-out bulb. Replace using 12V - 20W max -

G4 max halogen bulbs only taking care not to touch them with

your hands.

3. Close the lighting unit (snap-on).

Fitting (Removing) the carbon filter - Fig. 2:

1. Remove the perimeter extraction panel.

2. Remove the grease filter.

3. Turn the side knobs 90° and then remove the filter holder (g).

4. Insert (or remove, if washing or replacing) the carbon filter (i)

inside the filter holder frame (h).

5. Refit the carbon filter frame, the grease filter and the perimeter

extraction panel in their proper places.

Fig. 2

Fig. 1

IF NL EGB PD GR

5019 418 33085

PROTECTING THE ENVIRONMENT

1. Packaging

Packaging materials are 100% recyclable and are marked with the

recycling symbol . Dispose of the appliance in conformity with

local environmental regulations. Packaging materials (plastic bags,

polystyrene, etc.) can be dangerous for children and should be kept

well out of their reach.

2. Product

This appliance is marked in compliance with European Directive

2002/96/EC on Waste Electrical and Electronic Equipment (WEEE).

By ensuring that this appliance is scrapped suitably, you can help

prevent potentially damaging consequences for the environment and

health.

The symbol on the appliance or accompanying documentation

indicates that this product should not be disposed of as unsorted

municipal waste but must be taken to a collection point for the

treatment of WEEE.

Disposal must be carried out in accordance with local environmental

regulations for waste disposal.

For further information on the treatment, recovery and recycling of this

appliance, contact your competent local authority, the collection service

for household waste or the shop where you purchased the appliance.

PRECAUTIONS AND GENERAL

RECOMMENDATIONS

WARNING!

• The appliance is not intended for use by young children or

persons with restricted physical, sensory or mental

abilities or without experience and knowledge of the

appliance, unless they are under the supervision or

instruction of a person responsible for their safety.

• Young children should be supervised to ensure that they do

not play with the appliance.

1. Do not connect the appliance to the mains power supply until

installation has been fully completed. Always disconnect the hood

before cleaning or carrying out maintenance by unplugging it or

switching off the power supply.

2. Do not flambé food under the hood. Naked flames could cause a

fire.

3. Do not leave pans unattended when frying. Cooking oil can

catch fire.

4. Regular cleaning and maintenance is essential to correct functioning

and good performance. Regularly remove dirt deposits. Regularly

clean or replace filters. Never use flammable materials as hoses for

extracted air.

5. If the hood is used together with other appliances powered by gas

or other fuels, ambient negative pressure must not exceed 4Pa

(4 x 10-5 bar). For this reason, make sure the room is adequately

ventilated.

6. Exhaust air must not be conveyed through the same flue used by

the heating system or other appliances powered by gas or other

fuels.

7. The room must be adequately ventilated when the hood is used

together with appliances powered by gas or other fuels.

8. When replacing the bulbs, first ensure that they are cold.

9. The discharge air must not be ducted to a flue used for removing

fumes produced by appliances using gas or other fuels, but must

have a separate outlet. All national regulations on air discharge

must be observed.

10. The hood is not a shelf. It must not be overloaded or used to

carry objects

Note: always wear work gloves for all installation and maintenance

operations.

Electrical connections

The mains power supply must correspond to the voltage indicated

on the appliance rating plate located inside the hood. If it is fitted

with a plug, connect the hood to a power socket that complys with

applicable standards and is in an easily accessible location. If it is not

fitted with a plug (direct connection to the power supply) or if the

socket is not in an easily accessible location, fit a two-pole switch in

compliance with regulations, to ensure complete disconnection from

the mains voltage in conditions of category III overvoltage, according

to the rules for proper installation.

WARNING: Before reconnecting the hood circuit to the

mains power supply and checking correct operation, make

sure the power cable is correctly fitted and that it was NOT

crushed in the housing during installation.

Cleaning the hood

Warning! Failure to remove oil and grease (at least once a month) could

lead to fire.

Use a soft cloth with a neutral detergent. Never use abrasive

substances or alcohol.

Before using the hood

Please read these instructions carefully and keep them for future

reference, in order to ensure best use of your hood.

Packaging materials (plastic bags, polystyrene, etc.) can be dangerous

for children and should be kept well out of their reach.

Make sure the hood has not been damaged during transport.

Declaration of conformity

This product has been designed, manufactured and sold in

compliance with the following standards:

- safety objectives of "Low Voltage" Directive 73/23/EEC

- protection requirements of “EMC” Directive 89/336/EEC

amended by Directive 93/68/EEC.

Troubleshooting guide

The hood does not work:

• Is the plug properly inserted in the power socket?

• Is there a power failure?

The hood is not extracting efficiently:

• Is the right speed selected?

• Do the filters need cleaning or replacing?

• Are the air outlets blocked?

The light does not work:

• Does the bulb need replacing?

• Is the bulb correctly fitted?

AFTER-SALES SERVICE

Before calling the After-sales Service

1. Check if you can fix the problem yourself (see ”Troubleshooting

guide”).

2. Switch the hood off and then on again to check if the problem

has gone.

3. If the problem persists, contact the After-sales Service.

Specify:

•the nature of the problem,

• the model of hood, stated on the data plate inside the hood,

accessible by removing the grease filters.

• your full address,

• your telephone number and area code.

• the service code (the number appearing below the word

SERVICE on the data plate inside the hood behind the grease

filter).

If any repairs are needed, contact an authorized Service Centre

(to ensure that only original spare parts are used and that repairs are

made correctly).

Failure to comply with these instructions may compromise the safety

and quality of the product.

Bauknecht DBR 6990/IN Program Chart

Brand: Bauknecht

Model: DBR 6990/IN

Category: Cooker hoods

Type: Program Chart

This manual is also suitable for

DBR 6990/IN/PT

Download PDF

report

Bauknecht DBR 6990/IN Program Chart

This manual is also suitable for

Bauknecht DBR 6990/IN Program Chart

Related papers

Other documents