Altera Arria 10 Avalon-ST Interface User manual

Brand: Altera

Model: Arria 10 Avalon-ST Interface

Category: Software

Type: User manual

Arria 10 Avalon-MM DMA Interface for PCIe Solutions

User Guide

Last updated for Quartus Prime Design Suite: 15.1

Send Feedback

UG-01145_avmm_dma

2015.11.02

101 Innovation Drive

San Jose, CA 95134

www.altera.com

Datasheet

2015.11.02

UG-01145_avmm_dma

Send Feedback

Arria 10 Avalon-MM DMA Interface for PCIe Datasheet

Altera

Arria 10 FPGAs include a configurable, hardened protocol stack for PCI Express

that is

compliant with PCI Express Base Specification 3.0.

The Arria

10 Hard IP for PCI Express with the Avalon

Memory-Mapped (Avalon-MM) DMA

interface removes some of the complexities associated with the PCIe protocol. For example, the IP core

handles TLP encoding and decoding. In addition, the IP core includes Read DMA and Write DMA

engines. If you have already architected your own DMA system with the Avalon-MM interface, you may

want to continue to use that system. However, you may benefit from the simplicity of having the included

DMA engines. New users of this protocol should use this IP core. This variant is available in Qsys for 128-

and 256-bit interfaces to the Application Layer. The Avalon-MM interface and DMA engines are

implemented in FPGA soft logic.

Figure 1-1: Arria 10 PCIe Variant with Avalon-MM DMA Interface

The following figure shows the high-level modules and connecting interfaces for this variant.

Avalon-MM

DMA

Bridge

PCIe Hard IP

Block

PIPE

Interface

PHY IP Core

for PCIe

(PCS/PMA)

Serial Data

Transmission

Application

Layer

(User Logic)

Avalon-MM with

DMA Interface

trademarks of Altera Corporation and registered in the U.S. Patent and Trademark Office and in other countries. All other words and logos identified as

trademarks or service marks are the property of their respective holders as described at www.altera.com/common/legal.html. Altera warrants performance

of its semiconductor products to current specifications in accordance with Altera's standard warranty, but reserves the right to make changes to any

products and services at any time without notice. Altera assumes no responsibility or liability arising out of the application or use of any information,

product, or service described herein except as expressly agreed to in writing by Altera. Altera customers are advised to obtain the latest version of device

specifications before relying on any published information and before placing orders for products or services.

ISO

9001:2008

Registered

www.altera.com

101 Innovation Drive, San Jose, CA 95134

Table 1-1: PCI Express Data Throughput

The following table shows the aggregate bandwidth of a PCI Express link for Gen1, Gen2, and Gen3 for 2, 4, and 8

lanes. The protocol specifies 2.5 giga-transfers per second for Gen1, 5.0 giga-transfers per second for Gen2, and

8.0 giga-transfers per second for Gen3. This table provides bandwidths for a single transmit (TX) or receive (RX)

channel. The numbers double for duplex operation. Gen1 and Gen2 use 8B/10B encoding which introduces a 20%

overhead. In contrast, Gen3 uses 128b/130b encoding which introduces only a 1.5% overhead.

Units are Gigabits per second (Gbps).

Link Width

×2 ×4 ×8

PCI Express Gen1 (2.5 Gbps)

N/A N/A

16 Gbps

PCI Express Gen2 (5.0 Gbps) N/A 16 Gbps 32 Gbps

PCI Express Gen3 (8.0 Gbps) 15.75 Gbps 31.51 Gbps 63Gbps

Related Information

• Introduction to Altera IP Cores

Provides general information about all Altera IP cores, including parameterizing, generating,

upgrading, and simulating IP.

• Creating Version-Independent IP and Qsys Simulation Scripts

Create simulation scripts that do not require manual updates for software or IP version upgrades.

• Project Management Best Practices

Guidelines for efficient management and portability of your project and IP files.

• PCI Express Base Specification 3.0

• AN 690: PCI Express DMA Reference Design for Stratix V Devices

This reference design includes an Avalon-MM with DMA interface to the Application Layer. It

illustrates chaining DMA performance using internal memory.

• AN 708: PCI Express DMA Reference Design Using External DDR3 Memory for Stratix V and

Arria V GZ Devices

This reference design includes an Avalon-MM with DMA interface to the Application Layer. It

illustrates chaining DMA performance using external DDR3 memory.

• Creating a System with Qsys

1-2

Arria 10 Avalon-MM DMA Interface for PCIe Datasheet

UG-01145_avmm_dma

2015.11.02

Altera Corporation

Datasheet

Send Feedback

Features

New features in the Quartus

Prime 15.1 software release:

• Improved component GUI that simplifies parameterization. Among the changes is a new single

parameter, HIP mode that combines all supported data rates, interface widths, and frequencies as a

single parameter.

• New Generate Design Example option that automatically generates both simulation and hardware

example designs with the parameters that you specify. You can also download the hardware example

design directly to the Arria 10 FPGA Development Kit.

• Support for 256 tags for the Avalon-MM DMA read channel, enhancing performance for high latency

designs.

• Support for Completion buffer overflow monitoring.

• Support for immediate write for 32-bit data.

The Arria 10 Avalon-MM DMA for PCI Express supports the following features:

• Complete protocol stack including the Transaction, Data Link, and Physical Layers implemented as

hard IP.

• Native support for Gen1 x8, Gen2 x4, Gen2 x8, Gen3 x2, Gen3 x4, Gen3 x8 for Endpoints. The variant

downtrains when plugged into a lesser link width or changes to a different maximum link rate.

• Dedicated 16 kilobyte (KB) receive buffer.

• Support for 128- or 256-bit Avalon-MM interface to Application Layer with embedded DMA up to

Gen3 ×8 data rate.

• Support for 32- or 64-bit addressing for the Avalon-MM interface to the Application Layer.

• Qsys design example demonstrating parameterization, design modules, and connectivity.

• Extended credit allocation settings to better optimize the RX buffer space based on application type.

• Optional end-to-end cyclic redundancy code (ECRC) generation and checking and advanced error

reporting (AER) for high reliability applications.

• Easy to use:

• Flexible configuration.

• No license requirement.

• Design examples to get started.

Table 1-2: Feature Comparison for all Hard IP for PCI Express IP Cores

The table compares the features of the three mainstream Hard IP for PCI Express IP Cores. Refer to the Arria 10

Avalon-ST Interface with SR-IOV PCIe Solutions User Guide for the features of that variant.

Feature Avalon-ST Interface Avalon-MM Interface Avalon-MM DMA

IP Core License Free Free Free

Native Endpoint Supported Supported Supported

Root port Supported Supported Not Supported

Gen1 ×1, ×2, ×4, ×8 ×1, ×2, ×4, ×8 x8

UG-01145_avmm_dma

2015.11.02

Features

1-3

Datasheet

Altera Corporation

Send Feedback

Feature Avalon-ST Interface Avalon-MM Interface Avalon-MM DMA

Gen2 ×1, ×2, ×4, ×8 ×1, ×2, ×4, ×8 ×4, ×8

Gen3 ×1, ×2, ×4, ×8 ×1, ×2, ×4 ×2, ×4, ×8

64-bit Application

Layer interface

Supported Supported Not supported

128-bit Application

Layer interface

Supported Supported Supported

256-bit Application

Layer interface

Supported Not Supported Supported

Maximum payload

size

128, 256, 512, 1024,

2048 bytes

128, 256 bytes 128, 256 bytes

Number of tags

supported for non-

posted requests

256 8 16 or 256

Automatically handle

out-of-order

completions

(transparent to the

Application Layer)

Not supported Supported Supported

Automatically handle

requests that cross 4

KB address boundary

(transparent to the

Application Layer)

Not supported Supported Supported

Polarity Inversion of

PIPE interface signals

Supported Supported Supported

Number of MSI

requests

1, 2, 4, 8, 16, or 32 1, 2, 4, 8, 16, or 32 1, 2, 4, 8, 16, or 32

MSI-X Supported Supported Supported

Legacy interrupts Supported Supported Supported

Expansion ROM Supported Not supported Not supported

1-4

Features

UG-01145_avmm_dma

2015.11.02

Altera Corporation

Datasheet

Send Feedback

Table 1-3: TLP Support Comparison for all Hard IP for PCI Express IP Cores

The table compares the TLP types that the four Hard IP for PCI Express IP Cores can transmit. Each entry

indicates whether this TLP type is supported (for transmit) by endpoints (EP), Root Ports (RP), or both (EP/RP).

TLP (Transmit Support) Avalon-ST Interface Avalon-MM Interface Avalon-MM DMA

Memory Read Request

(Mrd)

EP/RP EP/RP Not supported

Memory Read Lock

Request (MRdLk)

EP/RP Not supported

Memory Write Request

(MWr)

EP/RP EP/RP Not supported

I/O Read Request

(IORd)

EP/RP EP/RP Not supported

I/O Write Request

(IOWr)

EP/RP EP/RP Not supported

Config Type 0 Read

Request (CfgRd0)

RP RP Not supported

Config Type 0 Write

Request (CfgWr0)

RP RP Not supported

Config Type 1 Read

Request (CfgRd1)

RP RP Not supported

Config Type 1 Write

Request (CfgWr1)

RP RP Not supported

Message Request (Msg) EP/RP Not supported Not supported

Message Request with

Data (MsgD)

EP/RP Not supported Not supported

Completion (Cpl) EP/RP EP/RP EP

Completion with Data

(CplD)

EP/RP Not supported EP

Completion-Locked

(CplLk)

EP/RP Not supported Not supported

Completion Lock with

Data (CplDLk)

EP/RP Not supported Not supported

Fetch and Add

AtomicOp Request

(FetchAdd)

EP Not supported Not supported

The Arria 10 Avalon-MM DMA Interface for PCIe Solutions User Guide explains how to use this IP core

and not the PCI Express protocol. Although there is inevitable overlap between these two purposes, use

this document only in conjunction with an understanding of the PCI Express Base Specification.

UG-01145_avmm_dma

2015.11.02

Features

1-5

Datasheet

Altera Corporation

Send Feedback

Related Information

• Arria 10 Avalon-MM Interface for PCIe Solutions User Guide

• Arria 10 Avalon-ST Interface for PCIe Solutions User Guide

• Arria 10 Avalon-ST Interface with SR-IOV for PCIe Solutions User Guide

• PCI Express Base Specification 3.0

Release Information

Table 1-4: Hard IP for PCI Express Release Information

Item Description

Version 15.1

Release Date November 2015

Ordering Codes No ordering code is required

Product IDs

The Product ID and Vendor ID are not required

because this IP core does not require a license.

Vendor ID

Altera verifies that the current version of the Quartus Prime software compiles the previous version of

each IP core, if this IP core was included in the previous release. Altera reports any exceptions to this

verification in the Altera IP Release Notes or clarifies them in the Quartus Prime IP Update tool. Altera

does not verify compilation with IP core versions older than the previous release.

Related Information

Altera IP Release Notes

Device Family Support

Table 1-5: Device Family Support

Device Family Support

Arria 10

Preliminary. The IP core is verified with prelimi‐

nary timing models for this device family. The IP

core meets all functional requirements, but might

still be undergoing timing analysis for the device

family. It can be used in production designs with

caution.

Other device families Refer to the Altera's PCI Express IP Solutions web

page for support information on other device

families.

1-6

Release Information

UG-01145_avmm_dma

2015.11.02

Altera Corporation

Datasheet

Send Feedback

Related Information

• Altera's PCI Express Web Page

Design Examples

Qsys example designs are available for the Arria 10 Avalon-MM DMA for PCI Express IP Core. You can

download them from the <install_dir>/ip/altera/altera_pcie/altera_pcie_a10_ed/example_design/a10 directory.

Related Information

• Getting Started with the Avalon-MM DMA on page 3-1

• Arria 10 PCI Express Quick Start Guide on page 2-1

Debug Features

Debug features allow observation and control of the Hard IP for faster debugging of system-level

problems.

IP Core Verification

To ensure compliance with the PCI Express specification, Altera performs extensive verification. The

simulation environment uses multiple testbenches that consist of industry-standard bus functional

models (BFMs) driving the PCI Express link interface. Altera performs the following tests in the

simulation environment:

• Directed and pseudorandom stimuli test the Application Layer interface, Configuration Space, and all

types and sizes of TLPs

• Error injection tests inject errors in the link, TLPs, and Data Link Layer Packets (DLLPs), and check

for the proper responses

• PCI-SIG

Compliance Checklist tests that specifically test the items in the checklist

• Random tests that test a wide range of traffic patterns

Altera provides example designs that you can leverage to test your PCBs and complete compliance base

board testing (CBB testing) at PCI-SIG, upon request.

Compatibility Testing Environment

Altera has performed significant hardware testing to ensure a reliable solution. In addition, Altera

internally tests every release with motherboards and PCI Express switches from a variety of manufac‐

turers. All PCI-SIG compliance tests are run with each IP core release.

Performance and Resource Utilization

Because the PCIe protocol stack is implemented in hardened logic, it uses no core device resources (no

ALMs and no embedded memory).

UG-01145_avmm_dma

2015.11.02

Design Examples

1-7

Datasheet

Altera Corporation

Send Feedback

The Avalon-MM with DMA Arria 10 variants include an Avalon-MM DMA bridge implemented in soft

logic that operates as a front end to the hardened protocol stack. The following table shows the typical

expected device resource utilization for selected configurations using the current version of the Quartus

Prime software targeting an Arria 10 device. With the exception of M20K memory blocks, the numbers of

ALMs and logic registers are rounded up to the nearest 50.

Table 1-6: Performance and Resource Utilization Arria 10 Avalon-MM DMA for PCI Express

Data Rate, Number of

Lanes, and Interface Width

ALMs M20K Memory Blocks Logic Registers

Gen2 x8 128 12700 19 22300

Gen3 x8 256 18000 47 31450

Related Information

Fitter Resources Reports

Recommended Speed Grades

Recommended speed grades are pending characterization of production Arria 10 devices.

Table 1-7: Arria 10 Recommended Speed Grades for All Avalon-MM Widths and Frequencies

Lane Rate Link Width Interface Width Application Clock

Frequency (MHz)

Recommended Speed Grades

Gen1 ×8 128 Bits 125 –1, –2, –3, –4

Gen2

×4 128 bits 125 –1, –2, –3, –4

×8 128 bits 250 –1, –2, –3

(1)

Gen3

×2 128 bits 125 –1, –2, –3

(1)

×4 128 bits 250 –1, –2, –3

(1)

×8 256 bits 250 –1, –2, –3

(1)

Related Information

• Altera Software Installation and Licensing Manual

• Setting up and Running Analysis and Synthesis

(1)

The -4 speed grade is also possible for this configuration; however, it requires significant effort by the end

user to close timing.

1-8

Recommended Speed Grades

UG-01145_avmm_dma

2015.11.02

Altera Corporation

Datasheet

Send Feedback

Creating a Design for PCI Express

Before you begin

Select the PCIe variant that best meets your design requirements.

• Is your design an Endpoint or Root Port?

• What Generation do you intend to implement?

• What link width do you intend to implement?

• What bandwidth does your application require?

• Does your design require Configuration via Protocol (CvP)?

1. Select parameters for that variant.

2. For Arria 10 devices, you can use the new Example Design tab of the component GUI to generate a

design that you specify. Then, you can simulate this example and also download it to an Arria 10

FPGA Development Kit. Refer to the Arria 10 PCI Express IP Core Quick Start Guide for details.

3. For all devices, you can simulate using an Altera-provided example design. All of Altera's static PCI

Express example designs are available under <install_dir>/ip/altera/altera_pcie/altera_pcie_a10_ed/

example_design/a10. Alternatively, generate an example design that matches your parameter settings, or

create a simulation model and use your own custom or third-party BFM. The Qsys Generate menu

generates simulation models. Altera supports ModelSim-Altera for all IP. The PCIe cores support the

Aldec RivieraPro, Cadence NCsim, Mentor Graphics ModelSim, and Synopsys VCS and VCS-MX

simulators.

The Altera testbench and Root Port or Endpoint BFM provide a simple method to do basic testing of

the Application Layer logic that interfaces to the variation. However, the testbench and Root Port BFM

are not intended to be a substitute for a full verification environment. To thoroughly test your applica‐

tion, Altera suggests that you obtain commercially available PCI Express verification IP and tools, or

do your own extensive hardware testing, or both.

4. Compile your design using the Quartus Prime software. If the versions of your design and the Quartus

Prime software you are running do not match, regenerate your PCIe design.

5. Download your design to an Altera development board or your own PCB. Click on the All Develop‐

ment Kits link below for a list of Altera's development boards.

6. Test the hardware. You can use Altera's SignalTap

II Logic Analyzer or a third-party protocol

analyzer to observe behavior.

7. Substitute your Application Layer logic for the Application Layer logic in Altera's testbench. Then

repeat Steps 3–6. In Altera's testbenches, the PCIe core is typically called the DUT (device under test).

The Application Layer logic is typically called APPS.

Related Information

• Parameter Settings on page 4-1

• Getting Started with the Avalon-MM DMA on page 3-1

• Arria 10 PCI Express Quick Start Guide on page 2-1

• All Development Kits

UG-01145_avmm_dma

2015.11.02

Creating a Design for PCI Express

1-9

Datasheet

Altera Corporation

Send Feedback

• Altera Wiki PCI Express

For complete design examples and help creating new projects and specific functions, such as MSI or

MSI-X related to PCI Express. Altera Applications engineers regularly update content and add new

design examples. These examples help designers like you get more out of the Altera PCI Express IP

core and may decrease your time-to-market. The design examples of the Altera Wiki page provide

useful guidance for developing your own design. However, the content of the Altera Wiki is not

guaranteed by Altera.

1-10

Creating a Design for PCI Express

UG-01145_avmm_dma

2015.11.02

Altera Corporation

Datasheet

Send Feedback

Arria 10 PCI Express Quick Start Guide

2015.11.02

UG-01145_avmm_dma

Send Feedback

The Arria 10 Hard IP for PCI Express IP core includes programmed I/O (PIO) and DMA design

examples to help you understand usage. The PIO example transfers memory from a host processor to a

target device. It is appropriate for low-bandwidth applications. The DMA examples include both a simple

DMA design example and a high-performance chaining DMA. The DMA examples are appropriate for

high-bandwidth applications. These design examples automatically create the files necessary to simulate

and compile in the Quartus Prime software. You can download the compiled design to the Arria 10 GX

FPGA Development Kit. The design examples cover a wide range of parameters for the Avalon-ST,

Avalon-MM and Avalon-MM with DMA interfaces. However, the automatically generated design

examples do not cover all possible parameterizations of the PCIe IP Core. If you select an unsupported

parameter set, generations fails and provides an error message.

In addition, many static design examples for simulation are only available in the <install_dir>/ip/altera/

altera_pcie/altera_pcie_a10_ed/example_design/a10 directory.

Figure 2-1: Development Steps for the Design Example

Example

Design

Generation

Compilation

(Simulator)

Functional

Simulation

Compilation

(Quartus Prime)

Hardware

Testing

Design Example

trademarks of Altera Corporation and registered in the U.S. Patent and Trademark Office and in other countries. All other words and logos identified as

trademarks or service marks are the property of their respective holders as described at www.altera.com/common/legal.html. Altera warrants performance

of its semiconductor products to current specifications in accordance with Altera's standard warranty, but reserves the right to make changes to any

products and services at any time without notice. Altera assumes no responsibility or liability arising out of the application or use of any information,

product, or service described herein except as expressly agreed to in writing by Altera. Altera customers are advised to obtain the latest version of device

specifications before relying on any published information and before placing orders for products or services.

ISO

9001:2008

Registered

www.altera.com

101 Innovation Drive, San Jose, CA 95134

Directory Structure

Figure 2-2: Directory Structure for the Generated Design Example

<pcie_a10_hip_0_example_design>

pcie_example_design

pcie_example_design.qpf

Altera_PCIe_Interop_test.zip

Readme_Altera_PCIe_interop_Test.txt

synth

pcie_example_design_tb

software

windows

interop

sim

pcie_example_design_tb

pcie_example_design.qsf

pcie_example_design.sdc

pcie_example_design.qsys

Design Components for the Avalon-MM with DMA Testbench

Figure 2-3: Block Diagram for the Qsys DMA Design Example Simulation Testbench

Root Port BFM

(pcie_example_design_inst)

Host Memory

Descriptors

Data

Driver

Transaction,

Hard IP for PCIe

Data Link,

and

Physical

Layers

On-Chip

Memory

DMA Data

PCI Express Example Design Testbench

Descriptor

Controller

DMA Engine

Avalon-MM to

PCIe TLP

Bridge

Arria 10 Hard IP for PCI Express Using Avalon-MM

with DMA Application Layer Interface

Interconnect

hip_serial

hip_pipe

The DMA simulation testbench includes the following components.

2-2

Directory Structure

UG-01145_avmm_dma

2015.11.02

Altera Corporation

Arria 10 PCI Express Quick Start Guide

Send Feedback

• A Root Port BFM.

Note: This Root Port BFM provides a simple method to do basic testing of the Application Layer logic

that interfaces to the variation. However, the testbench and Root Port BFM are not intended to

be a substitute for a full verification environment. To thoroughly test your application, Altera

suggests that you obtain commercially available PCI Express verification IP and tools, or do

your own extensive hardware testing or both.

• A testbench driver that configures the Root Port, Endpoint, and programs the DMA to transfer data to

and from the On-Chip memory and Host Memory.

• A testbench monitor that checks expected results.

• The Arria 10 Hard IP for PCI Express Endpoint with the Instantiate internal descriptor controller

parameter enabled.

The automatically generated testbench performs downstream memory reads and writes. You can edit the

testbench parameters in pcie_example_design_tb.v to create a testbench that illustrates the following more

advanced DMA features:

• Host allocation of memory

• Descriptor instructions

• Upstream memory reads and writes

The simulation reports, "Simulation stopped due to successful completion" if no errors occur. The log file,

altpcie_monitor_a10_dlhip_tlp_file_log.log records each TLP for both the initial configuration of the

Root Port BFM, PCIe Endpoint, and the test program.

UG-01145_avmm_dma

2015.11.02

Design Components for the Avalon-MM with DMA Testbench

2-3

Arria 10 PCI Express Quick Start Guide

Altera Corporation

Send Feedback

Figure 2-4: Qsys System Contents for Arria 10 PCI Express DMA Design Example

This view of the Arria 10 PCI Express DMA Design Example shows only the Avalon-MM, clock, and reset

interfaces.

Generating the Design

Figure 2-5: Procedure

Start Parameter

Editor

Specify IP Variation

and Select Device

Select

Design Parameters

Initiate

Design Generation

Specify

Design Example

2-4

Generating the Design

UG-01145_avmm_dma

2015.11.02

Altera Corporation

Arria 10 PCI Express Quick Start Guide

Send Feedback

Figure 2-6: Example Design Tab

Initiates Design

Generation

Select Arria 10 FPGA

Development Kit ES2

Follow these steps to generate the design:

1. In the IP Catalog (Tools > IP Catalog), locate and select Arria 10 Hard IP for PCI Express. The

parameter editor appears.

2. Specify a top-level name and the folder for your custom IP variation, and the target device. Click OK.

Note:

The Quick Start Design Examples are only supported in Arria 10 devices.

3. On the IP Settings tabs, specify the parameters for your IP variation.

4. Turn on Instantiate internal descriptor controller parameter on the Avalon-MM Settings tab.

5. On the Example Design tab, select either the PIO or DMA design for your IP variation.

6. For Example Design Files, select the Simulation and Synthesis options.

7. For Generated HDL Format, only Verilog is available.

8. For Target Development Kit select the Arria 10 FPGA Development Kit ES2 option.

Note:

SRAM object file (.sof) generation is only supported for Arria 10 ES2 devices in the 15.1

Quartus Prime release. Arria 10 production devices will be available in a future Quartus Prime

release.

9. Click the Generate Example Design button. The software generates all files necessary to run

simulations and hardware tests on the Arria 10 FPGA Development Kit ES2.

UG-01145_avmm_dma

2015.11.02

Generating the Design

2-5

Arria 10 PCI Express Quick Start Guide

Altera Corporation

Send Feedback

Compiling and Simulating the Design

Figure 2-7: Procedure

Change to

Directory.

Run

<Simulation Script>.

Analyze

Results.

1. Change to the simulation directory.

2. Run the simulation script for the simulator of your choice. Refer to the table below.

3. Analyze the results.

Table 2-1: Steps to Run Simulation

Simulator Working Directory Instructions

ModelSim <example_design>/pcie_example_

design_tb/pcie_example_design_tb/

sim/mentor/

1. To run the DMA design example that demonstrates

both downstream and upstream traffic, open

<example_design>/pcie_example_design_tb/pcie_

example_design_tb/sim/pcie_example_design_tb.v and

change the value of apps_type_hwtcl to 6.

do msim_setup.tcl

ld_debug

run -all

5. A successful simulation ends with the following

message, "Simulation stopped due to successful

completion!"

2-6

Compiling and Simulating the Design

UG-01145_avmm_dma

2015.11.02

Altera Corporation

Arria 10 PCI Express Quick Start Guide

Send Feedback

Simulator Working Directory Instructions

VCS <example_design>/pcie_example_

design_tb/pcie_example_design_tb/

sim/synopsys/vcs

1. To run the DMA design example that demonstrates

both downstream and upstream traffic, open

<example_design>/pcie_example_design_tb/pcie_

example_design_tb/sim/pcie_example_design_tb.v and

change the value of apps_type_hwtcl to 6.

2. Create a shell script, my_setup.sh. This script allows

you to add additional commands and override the

defaults included in vcs_setup.sh.

3. Include the following command in my_setup.sh:

source vcs_setup.sh USER_DEFINED_SIM_

OPTIONS=""

4. Type the following commands:

chmod +x *.sh

./my_setup.sh

5. A successful simulation ends with the following

message, "Simulation stopped due to successful

completion!"

Cadence <example_design>/pcie_example_

design_tb/pcie_example_design_tb/

sim/cadence

1. To run the DMA design example that demonstrates

both downstream and upstream traffic, open

<example_design>/pcie_example_design_tb/pcie_

example_design_tb/sim/pcie_example_design_tb.v and

change the value of apps_type_hwtcl to 6.

2. Create a shell script, my_setup.sh. This script allows

you to add additional commands and override the

defaults included in ncsim_setup.sh.

3. Include the following command in my_setup.sh:

source ncsim_setup.sh USER_DEFINED_SIM_

OPTIONS=""

chmod +x *.sh

./my_setup.sh

6. A successful simulation ends with the following

message, "Simulation stopped due to successful

completion!"

UG-01145_avmm_dma

2015.11.02

Compiling and Simulating the Design

2-7

Arria 10 PCI Express Quick Start Guide

Altera Corporation

Send Feedback

Figure 2-8: Partial Transcript from Successful Avalon-MM DMA Simulation Testbench

2-8

Compiling and Simulating the Design

UG-01145_avmm_dma

2015.11.02

Altera Corporation

Arria 10 PCI Express Quick Start Guide

Send Feedback

Compiling and Testing the Design in Hardware

Figure 2-9: Procedure

Compile Design

in Quartus Prime

Software.

Set up hardware. Program Device.

Test Design

in Hardware.

Figure 2-10: Software Application to Test the PCI Express Design Example on the Arria 10 GX FPGA

Development Kit

A software application running on a Windows PC performs the same hardware test for all of the PCI

Express Design Examples.

The software application is available on both 32- and 64-bit Windows platforms. This program performs

the following tasks:

1. Prints the Configuration Space, lane rate, and lane width.

2. Writes 0x00000000 to the specified BAR at offset 0x00000000 to initialize the memory and read it back.

3. Writes 0xABCD1234 at offset 0x00000000 of the specified BAR. Reads it back and compares.

If successful, the test program displays the message 'PASSED'

UG-01145_avmm_dma

2015.11.02

Compiling and Testing the Design in Hardware

2-9

Arria 10 PCI Express Quick Start Guide

Altera Corporation

Send Feedback

Page is loading ...

Altera Arria 10 Avalon-ST Interface User manual

Brand: Altera

Model: Arria 10 Avalon-ST Interface

Category: Software

Type: User manual

Download PDF

report

Altera Arria 10 Avalon-ST Interface User manual

Altera Arria 10 Avalon-ST Interface User manual

Related papers

Other documents