H3C S3600-2P-OLT Installation guide

H3C S3600 Series EPON OLT Switches

Installation Manual

Hangzhou H3C Technologies Co., Ltd.

http://www.h3c.com

Manual Version: 6W100-20090520

No part of this manual may be reproduced or transmitted in any form or by any means without prior

written consent of Hangzhou H3C Technologies Co., Ltd.

Trademarks

H3C, , Aolynk, , H

3

Care,

, TOP G, , IRF, NetPilot, Neocean, NeoVTL,

SecPro, SecPoint, SecEngine, SecPath, Comware, Secware, Storware, NQA, VVG, V

2

G, V

n

G, PSPT,

XGbus, N-Bus, TiGem, InnoVision and HUASAN are trademarks of Hangzhou H3C Technologies Co.,

Ltd.

All other trademarks that may be mentioned in this manual are the property of their respective owners.

Notice

The information in this document is subject to change without notice. Every effort has been made in the

preparation of this document to ensure accuracy of the contents, but all statements, information, and

recommendations in this document do not constitute the warranty of any kind, express or implied.

Technical Support

customer_service@h3c.com

http://www.h3c.com

About This Manual

Organization

H3C S3600 Series EPON OLT Switches Installation Manual is organized as follows:

Part Contents

1 Product Overview

Briefly introduces the appearance, system

description, as well as the features and

applications of the H3C S3600 series EPON

OLT switches.

2 Installation Preparations

Describes the requirements on installation site,

the safety recommendations before and during

installation, and the required tools.

3 Installing a Switch

Covers the procedures for installing the H3C

S3600 series EPON OLT switches, ground wire

connection, and so on.

4 Initial Power-On

Helps you get familiar with the basic knowledge

of how to boot and configure the H3C S3600

series EPON OLT switches, including device

startup, power-on, and initialization of system

files, and so on.

5 Maintaining Software

Introduces how to loading application files and

upgrading the BootWare program by using the

host software package.

6 Maintenance and Troubleshooting

Introduces how to maintain software and

hardware of the H3C S3600 series EPON OLT

switches.

Appendix

Appendix A: Lightning protection of the H3C

S3600 series EPON OLT switches.

Conventions

The manual uses the following conventions:

GUI conventions

Convention Description

Boldface

Window names, button names, field names, and menu items are in

Boldface. For example, the New User window appears; click OK.

>

Multi-level menus are separated by angle brackets. For example, File >

Create > Folder.

Convention Description

< > Button names are inside angle brackets. For example, click <OK>.

[ ]

Window names, menu items, data table and field names are inside

square brackets. For example, pop up the [New User] window.

/

Multi-level menus are separated by forward slashes. For example,

[File/Create/Folder].

Symbols

Convention Description

Means reader be extremely careful. Improper operation may cause

bodily injury.

Means reader be careful. Improper operation may cause data loss or

damage to equipment.

Means a complementary description.

Related Documentation

Manual Description

H3C S3600 Series EPON OLT Switches

Operation Manual

It is used for assisting the users in data

configurations and typical applications.

H3C S3600 Series EPON OLT Switches

Command Manual

It is used for assisting the users in using various

commands.

Obtaining Documentation

You can access the most up-to-date H3C product documentation on the World Wide Web at this URL:

http://www.h3c.com.

The following are the columns from which you can obtain different categories of product documentation:

[Products & Solutions]: Provides information about products and technologies, as well as solutions.

[Technical Support & Document > Technical Documents]: Provides several categories of product

documentation, such as installation, configuration, and maintenance.

[Technical Support & Document > Software Download]: Provides the documentation released with the

software version.

Documentation Feedback

You can e-mail your comments about product documentation to [email protected].

We appreciate your comments.

i

Table of Contents

1 Product Overview······································································································································1-1

Overview ·················································································································································1-1

S3600-2P-OLT/S3600-2P-OLT-DC ········································································································1-1

Front Panel ······································································································································1-2

Rear panel ·······································································································································1-5

Power Supply System ·····················································································································1-5

Ventilation System···························································································································1-5

The S3600 series EPON OLT switches system specifications·······························································1-6

2 Installation Preparations···························································································································2-1

Safety Precautions ··································································································································2-1

Installation Site········································································································································2-1

Temperature/Humidity·····················································································································2-1

Cleanness········································································································································2-1

Electromagnetic Susceptibility·········································································································2-2

Laser Safety ····································································································································2-2

Installation Tools ·····································································································································2-3

3 Installing a Switch ·····································································································································3-1

Installing a Switch ···································································································································3-1

Mounting a Switch on a Workbench································································································3-5

Connecting the Power Cord and the Ground Wire ·················································································3-5

Connecting the AC-Input Power Cord·····························································································3-5

Connecting the DC-Input Power Cord·····························································································3-6

Connecting the Ground Wire···········································································································3-7

Connecting the Switch to a Console Terminal······················································································3-10

Console Cable ·······························································································································3-10

Connecting the Console Cable······································································································3-10

Verifying Installation······························································································································3-11

4 Initial Power-On ·········································································································································4-1

Setting Up the Configuration Environment······························································································4-1

Connecting the Console Cable ···············································································································4-1

Connecting the Console Cable········································································································4-1

Setting Terminal Parameters ··················································································································4-2

Booting the Switch ··································································································································4-5

Checking Before Power-On·············································································································4-5

Powering On the Switch ··················································································································4-5

5 Maintaining Software·································································································································5-1

Overview ·················································································································································5-1

Files ·················································································································································5-1

BootWare Program File···················································································································5-1

Application Files ······························································································································5-1

Configuration Files···························································································································5-2

Software Maintenance Methods······································································································5-3

ii

BootWare Menu ······································································································································5-4

Main Menu·······································································································································5-4

Serial Sub-menu······························································································································5-6

Ethernet Sub-menu ·························································································································5-7

File Control Sub-menu·····················································································································5-8

BootWare Operation Sub-menu ······································································································5-8

Device Control Sub-menu ···············································································································5-9

Updating BootWare and Applications Through a Serial Interface ··························································5-9

Introduction to Xmodem ··················································································································5-9

Modifying Serial Interface Parameters ··························································································5-10

Updating an Application·················································································································5-11

Updating BootWare ·······················································································································5-13

Updating BootWare and Applications Using TFTP···············································································5-15

Updating an Application Using TFTP on the BootWare Menu······················································5-15

Updating and Backing Up an Application Using TFTP at the CLI·················································5-17

Updating BootWare and Applications Using FTP ·················································································5-19

Updating an Application Using FTP on the BootWare Menu ························································5-19

Updating and Backing Up an Application Using FTP at the CLI ···················································5-19

Maintaining Application and Configuration Files···················································································5-24

Displaying All Files ························································································································5-24

Setting Application Files Attributes································································································5-25

Deleting a File································································································································5-26

Backing Up and Restoring BootWare ···································································································5-27

Backing Up the Entire BootWare···································································································5-27

Restoring the Entire BootWare······································································································5-28

6 Maintenance and Troubleshooting··········································································································6-1

File Loading Failure·································································································································6-1

Password Loss········································································································································6-1

User Password Loss························································································································6-1

BootWare Password Loss ···············································································································6-2

Super Password Loss······················································································································6-3

Power Supply Failure······························································································································6-4

Configuration Terminal Failure················································································································6-4

1-1

1 Product Overview

Overview

The H3C S3600 Series EPON OLT Switches (referred to as the S3600 OLT series hereinafter) are

Ethernet switches developed by H3C. The S3600 OLT series, the H3C S7500E series and the EPON

series line processing units (LPU) can deliver the EPON OLT function, and operate as intelligent

campus access and distribution layer switches in high-performance Ethernet Passive Optical Networks

(EPONs).

The S3600 OLT series include the following models as shown in

Table 1-1.

Table 1-1 The S3600 OLT series models

Model

Power

supply

Number

of service

ports

1000 M port OLT port

Console

port

S3600-2P-OLT

AC power

input

4

z Two

10/100/1000Base-T

X Ethernet ports

z Two

100Base-FX/1000B

ase-X SFP ports

(Combo)

Two

1000Base-P

X OLT ports

1

S3600-2P-OLT-

DC

DC power

input

4

z Two

10/100/1000Base-T

X Ethernet ports

z Two

100Base-FX/1000B

ase-X SFP ports

(Combo)

Two

1000Base-P

X OLT ports

1

S3600-2P-OLT/S3600-2P-OLT-DC

The S3600-2P-OLT and S3600-2P-OLT-DC are similar except their power input. This section uses an

S3600-2P-OLT as an example unless otherwise specified.

1-2

Front Panel

The S3600-2P-OLT provides two 1000 M Ethernet ports (10/100/1000Base-TX), two 1000 M SFP ports

(100Base-FX/1000Base-X), two OLT ports (1000Base-PX SFP), and one console port on the front

panel. The appearance of the front panel is as shown in

Figure 1-1.

Figure 1-1 S3600-2P-OLT front panel

(1) Power LED (2) OLT port

(3) 1000 Mbps Ethernet port (4) 1000 Mbps SFP port

(5) Console port (6) OLT port status LED

(7) 1000 Mbps Ethernet port status LED (8) 1000 Mbps SFP port status LED

LEDs on the Front Panel

The S3600-2P-OLT provides one power LED, two OLT port status LEDs, two 1000 Mbps Ethernet port

status LEDs and two 1000 Mbps SFP port LEDs on the front panel. See

Table 1-2 for descriptions about

LEDs.

Table 1-2 Descriptions about LEDs

LED Mark Status Description

On The switch is powered on.

Power LED POWER

Off

The switch is powered off or the

power supply system fails.

On A link is present on the port.

1000Base-PX OLT

port status LED

LINK

Off No link is present on the port.

On

A link is present but no data is

being transmitted/received.

Off No link is present on the port.

10/100/1000Base-T

X Ethernet port

status LED

LINK/ACT

Flashing

Data is being transmitted or

received on the port.

On

A link is present but no data is

being transmitted/received.

Off No link is present on the port.

100Base-FX/1000B

ase-X SFP port

status LED

LINK/ACT

Flashing

Data is being transmitted or

received on the port.

1-3

OLT port

The S3600-2P-OLT provides two 1000Base-PX EPON OLT ports to connect the optical network units

(ONUs) through the optical distribution network (ODN), thus forming an EPON access system.

Table 1-3 OLT port specifications

Item Specification

Connector type SFP

Connector quantity 2

Interface attribute 1000Base-PX

Standard IEEE 802.3ah

Supported optical transceivers and transmission

distances

z SFP-GE-PX10-D-SM1490-A: 10 km (6.21

miles)

z SFP-GE-PX20-D-SM1490-A: 20 km (12.43

miles)

z For the models and specifications of each kind of transceivers, refer to H3C Mid-Range Series

Ethernet Switches Pluggable Modules Manual.

z The types of SFP transceivers may update with time. For information about transceivers, contact

technical support.

Uplink Port

The S3600-2P-OLT provides two 100Base-FX/1000Base-X SFP ports, which work in conjunction with

the two provided 10/100/1000Base-T autosensing Ethernet ports (RJ-45) to form two combo ports for

uplink connections. Only one of the two ports forming a compo port can be used at a time.

The two ports forming a combo port serve as backup for each other. Once the active port fails, data is

automatically switched to the standby port for transmission, thus ensuring high network availability.

You can plug in SFP transceiver on the SFP interfaces as needed, increasing the networking flexibility.

Table 1-4 Adaptable 1000 Mbps SFP transceivers

Transceiver Models

1000 Mbps SFP transceivers

z SFP-GE-SX-MM850-A

z SFP-GE-LX-SM1310-A

z SFP-GE-LH40-SM1310

z SFP-GE-LH40-SM1550

z SFP-GE-LH70-SM1550

z SFP-GE-LH100-SM1550

1000 Mbps BIDI transceivers

z SFP-GE-LX-SM1310-BIDI

z SFP-GE-LX-SM1490-BIDI

1-4

Transceiver Models

1000 Mbps CWDM transceivers

z SFP-GE-LH70-SM1470-CW

z SFP-GE-LH70-SM1490-CW

z SFP-GE-LH70-SM1510-CW

z SFP-GE-LH70-SM1530-CW

z SFP-GE-LH70-SM1550-CW

z SFP-GE-LH70-SM1570-CW

z SFP-GE-LH70-SM1590-CW

z SFP-GE-LH70-SM1610-CW

Table 1-5 Adaptable 100 Mbps SFP transceivers

Transceiver Models

100 Mbps SFP transceivers

z SFP-FE-SX-MM1310-A

z SFP-FE-LX-SM1310-A

z SFP-FE-LH40-SM1310

z SFP-FE-LH80-SM1550

100 Mbps BIDI transceivers

z SFP-FE-LX-SM1310-BIDI

z SFP-FE-LX-SM1550-BIDI

z For the models and specifications of each kind of transceivers, refer to H3C Mid-Range Series

Ethernet Switches Pluggable Modules Manual.

z The types of SFP transceivers may update with time. For information about transceivers, contact

technical support.

Table 1-6 describes the specifications of the two 10/100/1000Base-T Ethernet ports.

Table 1-6 10/100/1000Base-T Ethernet port specifications

Item Specification

Connector type RJ-45

Connector quantity 2

Interface standard

z 10 Mbps, full/half duplex

z 100 Mbps, full/half duplex

z 1000 Mbps, full/half duplex

z MDI/MDI-X, auto-sensing

Standard

IEEE 80802.3u

IEEE 802.3ab

Transmission medium and max

transmission distance

Category-5 unshielded twisted pair cable

Console Port

Each S3600-2P-OLT provides one console port on the front panel. Table 1-7 describes the console port

specifications.

1-5

Table 1-7 Console port specifications

Item Specification

Connector type

RJ-45

Compliant standard EIA/TIA-232

Transmission baud

rate

9600 bps to 115200 bps (defaulting to 9600 bps)

Service

z It can be connected to an ASCII terminal.

z It can be connected to a serial port of a local or remote (through a pair of

modems) PC running terminal emulation program.

Rear panel

S3600-2P-OLT rear panel

Figure 1-2 S3600-2P-OLT rear panel

(1) Grounding screw (2) AC receptacle

S3600-2P-OLT-DC rear panel

Figure 1-3 S3600-2P-OLT-DC rear panel

(1) Grounding screw (2) DC receptacle

Power Supply System

S3600-2P-OLT AC input voltage

z Rated voltage: 100 VAC to 240 VAC, 50/60 Hz

z Max voltage: 90 VAC to 264 VAC, 50/60 Hz

S3600-2P-OLT-DC DC input voltage

z Rated voltage: –48 VDC to –60 VDC

z Max voltage: –36 VDC to –72 VDC

Ventilation System

The S3600-2P-OLT/S3600-2P-OLT-DC provides one fan for heat dissipation of the whole system.

1-6

The S3600 series EPON OLT switches system specifications

Table 1-8 The S3600 series system specifications

Item Specifications

S3600-2P-OLT Physical

dimensions (H

× W × D)

S3600-2P-OLT-DC

43.6 × 440 × 160 mm (1.72 × 17.32 × 6.30 in.)

S3600-2P-OLT

Weight

S3600-2P-OLT-DC

2.14 kg (4.72 lb)

Console port 1

S3600-2P-OLT

Service ports

S3600-2P-OLT-DC

z Two 10/100/1000Base-TX Ethernet ports and two

100Base-FX/1000Base-X SFP ports (Combo)

z Two 1000Base-PX OLT ports

Input voltage

z S3600-2P-OLT support AC input

Rated voltage: 100 VAC to 240 VAC, 50/60 Hz

Max voltage: 90 VAC to 264 VAC, 50/60 Hz

z S3600-2P-OLT-DC support DC input

Rated voltage: –48 VDC to –60 VDC

Max voltage: –36 VDC to –72 VDC

S3600-2P-OLT

Power

consumption

S3600-2P-OLT-DC

z Min: 11 W

z Max: 20 W

Operating

temperature

0°C to 45°C (32°F to 113°F)

Operating

humidity

(noncondensi

ng)

10% to 95%

2-1

2 Installation Preparations

Safety Precautions

To avoid any device impairment and bodily injury caused by improper use, observe these rules:

z Before cleaning the switch, plug out the power cord of the power module of the switch first. Do not

clean the switch with wet cloth or liquid.

z Do not place the switch near water or in a damp environment. Prevent water or moisture from

entering the switch chassis.

z Do not place the switch on an unstable case or desk. The switch might be damaged severely in

case of a fall.

z Ensure proper ventilation of the equipment room and keep the ventilation vents of the switch free of

obstruction.

z Make sure that the operating voltage is in the range labeled on the power module of the switch.

z Do not open the chassis to avoid electrical shocks when the switch is operating or just when the

switch is powered off.

z When replacing interface module, wear ESD-preventive gloves to avoid damaging the units.

Installation Site

The S3600 series EPON OLT switches must be used indoors. You can mount the switch in a rack or on

a workbench, but make sure:

z Adequate clearance is reserved at the air inlet/exhaust vents for ventilation.

z The rack or workbench has a good ventilation system.

z The rack is sturdy enough to support the device and its accessories.

z The rack or workbench is well earthed.

To ensure normal operation and long service life of your switch, install it in an environment that meets

the requirements described in the following subsections.

Temperature/Humidity

You must maintain a proper temperature and humidity in the equipment room. Long-term high humidity

may lead to bad insulation, electricity leakage, mechanical property changes, and metal corrosion.

However, if the relative humidity is too low, captive screws may become loose as the result of

contraction of insulation washers and static electricity may be produced in a dry environment to

jeopardize the circuits on the device. A high temperature is the most undesirable condition, because it

accelerates the aging of insulation materials and thus significantly lowers reliability and service life of

the switch.

For the temperature and humidity requirements, refer to

Table 1-8 on page 1-6.

Cleanness

Dust is a hazard to the operating safety of your device. The dust accumulated on the chassis can be

adsorbed by static electricity and result in poor contact of metal connectors or metal contact points.

2-2

Especially when the indoor relative humidity is low, electrostatic adsorption is more likely to happen.

This can not only shorten the service life of your device but also cause communications failures. The

following table lists the dust concentration limit.

Table 2-1 Dust concentration limit in the equipment room

Substance Concentration limit (particles//m³)

Dust

≤ 3 x 10

4

(no visible dust on the tabletop over three days)

Note: The dust diameter is greater than or equal to 5 μm.

Besides dust, there are rigorous limits on the content of harmful substances in the air that can

accelerate the corrosion and aging of metals, such as chloride, acid, and sulfide in the equipment room.

The equipment room must be protected against ingression of harmful gases such as SO

2

, H

2

S, NH

3

,

and Cl

2

. For specific requirements, see the following table.

Table 2-2 Harmful gas limits in the equipment room

Gas Maximum concentration (mg/m

3

)

SO

2

0.2

H

2

S 0.006

NH

3

0.05

Cl

2

0.01

Electromagnetic Susceptibility

The operation of your switch can be affected by external interferences, such as conducted emission by

capacitance coupling, inductance coupling, electromagnetic wave radiation, and common impedance

(including the grounding system) coupling, and leads (power cables, signaling cables and output wires).

To eliminate the interferences, pay attention to the following:

z As the AC power system is a TN system, use a single-phase three-wire power socket with a

protection earth (PE) to effectively filter interference from the power grid.

z Keep the device far away from radio transmitting stations, radar stations, and high-frequency

devices.

z Use electromagnetic shielding, for example, shielded interface cables, when necessary.

z Route interface cables only indoors to prevent signal ports from getting damaged by over-voltage

or over-current caused by lightning strikes.

Laser Safety

The S3600 series EPON OLT switches are Class 1 laser devices.

When an optional interface module or SFP module on the S3600 series is operating, do not stare into

the optical port because the laser light emitted from the optical fiber may hurt your eyes.

2-3

Installation Tools

z Flat-blade screwdriver

z Phillips screwdriver

z ESD-preventive wrist strap

The installation tools are not shipped with the S3600 series.

3-1

3 Installing a Switch

On a mounting screw of the chassis of the H3C series switches, there is a seal labeled with H3C. You

need to keep it intact before asking the agent to maintain the switch. You need to get the permission of

the local agent before you can open the chassis. Otherwise, you will be responsible for irreversible

damages caused by your operations.

Installing a Switch

You can install a switch into a 19-inch standard cabinet in one of the following three ways:

z Use front mounting ears

z Use front mounting ears and a tray

z Use front mounting ears and guide rails

z The front mounting ears are provided in the standard package, while trays and guide rails are

optional parts that you need to order as needed.

z When installing devices, ensure a clearance of 1U (44.45 mm, or 1.75 in.) between devices for heat

dissipation.

z The guide rails provided by H3C are suitable for H3C 1000 mm (39.37 in.) standard cabinets only.

If the depth of your cabinet does not fit, use other supports to replace the guide rails.

z The switch for illustrating the installation procedures in the following sections is for reference only.

Introduction to mounting ear

Figure 3-1 shows the appearance of a front mounting ear.

3-2

Figure 3-1 Appearance of a standard front mounting ear

(1)

(2)

(1) Screw hole used to fix the mounting ear to the cabinet (Use one M6 screw)

(2) Screw hole used to fix the switch to the mounting ear

Use front mounting ears to install a switch

Follow these steps to mount a switch into a 19-inch standard cabinet:

1) Wear an ESD-preventive wrist strap to check the grounding and stability of the cabinet.

2) Take out the screws which are packed together with the front mounting ears, and fix one end of

mounting ears to the switch, as shown in

Figure 3-2.

Figure 3-2 Fix front mounting ears (1)

3) Place the switch horizontally in a proper position, and fix the other end of mounting ears to the front

brackets with screws and captive nuts, as shown in

Figure 3-3.

3-3

Figure 3-3 Fix front mounting ears (2)

Use front mounting ears and a tray

Follow these steps to install a switch into a 19-inch standard cabinet:

1) Wear an ESD-preventive wrist strap to check the grounding and stability of the cabinet.

2) Fix the delivered tray horizontally in a proper position.

3) Take out the screws which are packed together with the front mounting ears, and fix one end of

mounting ears to the switch, as shown in

Figure 3-2.

4) Place the switch on the tray horizontally, slide the tray into the cabinet, and fix the other end of

mounting ears to the front brackets with crews and captive nuts, as shown in

Figure 3-3.

Introduction to guide rail

Figure 3-4 shows the appearance of a guide rail.

Figure 3-4 Appearance of a guide rail

Slotted hole 1: Used to fix the guide rail to the rear bracket. You can adjust the screw hole position

according to the position of the switch.

Cooling hole: Used for heat dissipation between switch and cabinet

Slotted hole 2: Used to fix the guide rail to the front bracket

3-4

Use front mounting ears and guide rails

Follow these steps to install a switch into a 19-inch standard cabinet:

1) Wear an ESD-preventive wrist strap to check the grounding and stability of the cabinet.

2) Take out the screws packed together with the front mounting ears and fix one end of the front

mounting ears to the switch, as shown in

Figure 3-2.

3) Install guide rails on the brackets on both sides of the cabinet with M5 self-tapping screws, as

shown in

Figure 3-5.

Figure 3-5 Install guide rails

4) Hold the two sides of the switch and slide it gently along the guide rails into the cabinet until it is

located in a proper position, as shown in

Figure 3-6. Ensure that the bottom side of the guide rails

and the switch are in close contact.

Figure 3-6 Install front mounting ears and guide rails

Front panel

5) Fix the other end of front mounting ears to the front brackets of the cabinet with M6 screws and

captive nuts and ensure that the front mounting ears and guide rails have fixed the switch in the

cabinet securely, as shown in

Figure 3-7.

3-5

Figure 3-7 Effect diagram of front mounting ear and guide rail installation

Mounting a Switch on a Workbench

In many cases, standard 19-inch cabinets are not available. Therefore, switches are often placed on

clean workbenches. To place the switch on a workbench, follow these steps:

1) Place the switch with bottom up carefully, and then clean the round holes on the chassis bottom

with dry cloth.

2) Attach the rubber feet to the four round holes on the chassis bottom.

3) Place the switch with upside up on the workbench.

During the operation, you simply need to:

z Make sure that the workbench is flat and sturdy.

z Leave a clearance of 10 cm (3.94 in.) around the device for heat dissipation.

z Do not place heavy objects on the switch.

Connecting the Power Cord and the Ground Wire

Connecting the AC-Input Power Cord

The AC-input power cord is applicable only to the S3600-2P-OLT.

AC-input power socket (recommended)

You are recommended to use a single-phase three-line power socket with a ground contact or a general

purpose PC power socket, making sure that the power point is well connected to building ground.

Normally, the ground point of the power source in a building was buried in the ground during the

construction and wiring. Still, you must make sure of that.

Page is loading ...

H3C S3600-2P-OLT Installation guide

This manual is also suitable for

H3C S3600-2P-OLT Installation guide

Related papers

Other documents