H3C WX2540H Installation guide

H3C WX2540H Access Controlle

r

Installation Guide

New H3C Technologies Co., Ltd.

http://www.h3c.com.hk

Document version: 6W101-20170414

No part of this manual may be reproduced or transmitted in any form or by any means without prior

written consent of New H3C Technologies Co., Ltd.

Trademarks

H3C, , H3CS, H3CIE, H3CNE, Aolynk, , H

3

Care, , IRF, NetPilot, Netflow,

SecEngine, SecPath, SecCenter, SecBlade, Comware, ITCMM and HUASAN are trademarks of New

H3C Technologies Co., Ltd.

All other trademarks that may be mentioned in this manual are the property of their respective owners

Notice

The information in this document is subject to change without notice. Every effort has been made in the

preparation of this document to ensure accuracy of the contents, but all statements, information, and

recommendations in this document do not constitute the warranty of any kind, express or implied.

Environmental protection

This product has been designed to comply with the environmental protection requirements. The storage,

use, and disposal of this product must meet the applicable national laws and regulations.

Preface

The H3C WX2540H Access Controller Installation Guide describes preparing for installation, installing

the access controller, troubleshooting, and hardware management and maintenance of the WX2540H

access controller.

This preface includes the following topics about the documentation:

• Audience.

• Conventions.

• Obtaining documentation.

• Technical support

• Documentation feedback.

Audience

This documentation is intended for:

• Network planners.

• Field technical support and servicing engineers.

• Network administrators working with the WX2540H access controller.

Conventions

The following information describes the conventions used in the documentation.

Command conventions

Convention Descri

p

tion

Boldface Bold text represents commands and keywords that you enter literally as shown.

Italic Italic text represents arguments that you replace with actual values.

[ ] Square brackets enclose syntax choices (keywords or arguments) that are optional.

{ x | y | ... }

Braces enclose a set of required syntax choices separated by vertical bars, from which

you select one.

[ x | y | ... ]

Square brackets enclose a set of optional syntax choices separated by vertical bars, from

which you select one or none.

{ x | y | ... } *

Asterisk marked braces enclose a set of required syntax choices separated by vertical

bars, from which you select a minimum of one.

[ x | y | ... ] *

Asterisk marked square brackets enclose optional syntax choices separated by vertical

bars, from which you select one choice, multiple choices, or none.

&<1-n>

The argument or keyword and argument combination before the ampersand (&) sign can

be entered 1 to n times.

# A line that starts with a pound (#) sign is comments.

GUI conventions

Convention Descri

p

tion

Boldface

Window names, button names, field names, and menu items are in Boldface. For

example, the New User window opens; click OK.

> Multi-level menus are separated by angle brackets. For example, File > Create > Folder.

Symbols

Convention Descri

p

tion

WARNING

An alert that calls attention to important information that if not understood or followed can

result in personal injury.

CAUTION

An alert that calls attention to important information that if not understood or followed can

result in data loss, data corruption, or damage to hardware or software.

IMPORTANT

An alert that calls attention to essential information.

NOTE

An alert that contains additional or supplementary information.

TIP

An alert that provides helpful information.

Network topology icons

Represents a generic network device, such as a router, switch, or firewall.

Represents a routing-capable device, such as a router or Layer 3 switch.

Represents a generic switch, such as a Layer 2 or Layer 3 switch, or a router that supports

Layer 2 forwarding and other Layer 2 features.

Represents an access controller, a unified wired-WLAN module, or the access controller

engine on a unified wired-WLAN switch.

Represents an access point.

Wireless terminator unit.

Wireless terminator.

Represents a mesh access point.

Represents omnidirectional signals.

Represents directional signals.

T



Represents a security product, such as a firewall, UTM, multiservice security gateway, or

load balancing device.

Represents a security module, such as a firewall, load balancing, NetStream, SSL VPN,

IPS, or ACG module.

Examples provided in this document

Examples in this document might use devices that differ from your device in hardware model,

configuration, or software version. It is normal that the port numbers, sample output, screenshots, and

other information in the examples differ from what you have on your device.

Obtaining documentation

To access the most up-to-date H3C product documentation, go to the H3C website

at http://www.h3c.com.hk

.

To obtain information about installation, configuration, and maintenance, click

http://www.h3c.com.hk/Technical_Documents

To obtain software version information such as release notes, click

http://www.h3c.com.hk/Software_Download

Technical support

servic[email protected]

http://www.h3c.com.hk

Documentation feedback

You can email your comments about product documentation to info@h3c.com.

We appreciate your comments.



i

Contents

Preparing for installation ············································································································································· 1

Safety recommendations ·················································································································································· 1

General safety recommendations ··························································································································· 1

Electrical safety ························································································································································· 1

Laser safety ································································································································································ 2

Examining the installation site ········································································································································· 2

Temperature and humidity ······································································································································· 2

Cleanliness ································································································································································ 2

Cooling ······································································································································································ 3

ESD prevention ························································································································································· 3

EMI ············································································································································································· 3

Lightning protection ·················································································································································· 4

Installation accessories ····················································································································································· 4

Pre-installation checklist ···················································································································································· 4

Installing the device ····················································································································································· 6

Confirming installation preparations ······························································································································· 6

Installation flow ································································································································································· 6

Mounting the device on a workbench ···························································································································· 7

Grounding the device ······················································································································································· 7

Attaching the ring terminal to the grounding cable ······························································································ 7

Connecting the grounding cable to the device ····································································································· 8

Connecting the console cable and setting terminal parameters ·················································································· 8

Connecting the console cable ································································································································· 8

Setting terminal parameters ····································································································································· 9

Connecting the Ethernet cables ···································································································································· 12

Connecting a copper Ethernet port ····················································································································· 12

Connecting a fiber port ········································································································································ 12

Connecting the power adapter ···································································································································· 13

Verifying the installation ················································································································································ 14

Powering on the device ················································································································································· 14

Troubleshooting ·························································································································································· 17

Power failure ··································································································································································· 17

Symptom ································································································································································· 17

Solution ··································································································································································· 17

No display or garbled display on the configuration terminal ··················································································· 17

Symptom ································································································································································· 17

Solution ··································································································································································· 17

Software loading failure ················································································································································ 18

Symptom ································································································································································· 18

Resolution ······························································································································································· 18

Hardware management and maintenance ·············································································································· 19

Displaying hardware information for the device ········································································································ 19

Displaying operational statistics for the device ·································································································· 19

Displaying detailed information about the device ····························································································· 20

Displaying the electronic label data for the device ··························································································· 20

Displaying the CPU usage of the device············································································································· 21

Displaying the memory usage of the device ······································································································ 21

ii

Rebooting the device ····················································································································································· 22

Rebooting the device immediately at the CLI ····································································································· 23

Scheduling a device reboot ································································································································· 23

Appendix A Chassis views and technical specifications ························································································ 24

Chassis views ································································································································································· 24

Transceiver module, fiber connector, and optical fiber views ·················································································· 24

Technical specifications ················································································································································· 25

Transceiver module specifications ································································································································ 26

Interface arrangement ··················································································································································· 27

Appendix B LEDs ························································································································································ 28

LEDs ················································································································································································· 28

Index ··········································································································································································· 30

1

Preparing for installation

Safety recommendations

To avoid any equipment damage or bodily injury, read the following safety recommendations before

installation. Note that the recommendations do not cover every possible hazardous condition.

General safety recommendations

• Do not place the device on an unstable case or desk. The device might be severely damaged in

case of a fall.

• Make sure the ground is dry and flat and anti-slip measures are in place.

• Keep the chassis and installation tools away from walk areas.

• Keep the chassis clean and dust-free.

• Do not place the device near water or in a damp environment. Prevent water or moisture from

entering the device chassis.

• Ensure good ventilation of the equipment room and keep the air inlet and outlet vents of the device

free of obstruction.

• Make sure the device operates in the voltage range as required.

• Use a screwdriver to fasten screws.

• To prevent condensation, perform the following tasks:

{ Unpack the device a minimum of half an hour after you move the device from a location below

0°C (32°F) to the equipment room.

{ Power on the device a minimum of 2 hours after you move the device from a location below 0°C

(32°F) to the equipment room.

Electrical safety

• Carefully examine your work area for possible hazards, such as moist floors, ungrounded power

extension cables, or missing safety grounds.

• Locate the emergency power-off switch in the room before installation. Shut off the power

immediately if an accident occurs.

• Unplug all the external cables (including power cables) before moving the chassis.

• Do not work alone when the device has power.

• Always check that the power has been disconnected.

2

Laser safety

W

ARNING!

Do not stare into any fiber port when the device is powered on. The laser light emitted from the fiber por

t

might hurt your eyes.

• Before you disconnect a fiber connector, execute the shutdown command in interface view to

disable the optical source.

• After you remove an optical fiber from the connector, install the dust cover on the connector to avoid

connector damage.

Examining the installation site

The device can only be used indoors. To ensure correct operation and a long lifespan for your device, the

installation site must meet the requirements in this section.

Temperature and humidity

Maintain the temperature and humidity in the equipment room as described in Table 1.

• Lasting high relative humidity can cause poor insulation, electricity creepage, mechanical property

change of materials, and metal corrosion.

• Lasting low relative humidity can cause washer contraction and ESD and cause problems including

loose screws and circuit failure.

• High temperature can accelerate the aging of insulation materials and significantly lower the

reliability and lifespan of the device.

Table 1 Temperature/humidity requirements in the equipment room

Tem

p

erature Relative humidit

y

0°C to 40°C (32°F to 104°F) 5% to 95%, noncondensing

Cleanliness

Dust buildup on the chassis might result in electrostatic adsorption, which causes poor contact of metal

components and contact points, especially when indoor relative humidity is low. In the worst case,

electrostatic adsorption can cause communication failure.

Table 2 Dust concentration limit in the equipment room

Substance Concentration limit (

p

articles/m

3

)

Dust particles

≤ 3 x 10

4

(No visible dust on desk in three days)

NOTE:

Dust particle diameter ≥ 5 μm

3

The equipment room must also meet limits on salts, acids, and sulfides to eliminate corrosion and

premature aging of components, as shown in Table 3.

Table 3 Harmful gas li

mits in the equipment room

Gas Max. (m

g

/m

3

)

SO

2

0.2

H

2

S 0.006

NH

3

0.05

Cl

2

0.01

Cooling

• Leave a minimum of 10 cm (3.94 in) of clearance around the device.

• A good ventilation system is available at the installation site.

ESD prevention

The device might be damaged by the following Electrostatic discharge (ESD) sources:

• Outdoor environment—For example, high-voltage power line and lightning.

• Indoor environment—For example, floor carpet.

• Device internal system.

To prevent ESD damage, follow these guidelines:

• Ground the device reliably.

• Take dust-proof measures for the equipment room. For more information, see "Cleanliness."

• Maintain the

humidity and temperature at acceptable levels. For more information, see

"Temperature and humidity."

• Wear an ESD suit and an ESD wrist strap, wear ESD gloves, and remove any electrically conducting

objects such as watch or jewelry before handling the device.

EMI

All electromagnetic interference (EMI) sources, from outside or inside of the device and application

system, adversely affect the device in the following ways:

• A conduction pattern of capacitance coupling.

• Inductance coupling.

• Electromagnetic wave radiation.

• Common impedance (including the grounding system) coupling.

To prevent EMI, perform the following tasks:

• If AC power is used, use a single-phase three-wire power receptacle with protection earth (PE) to

filter interference from the power grid.

• Keep the device far away from radio transmitting stations, radar stations, and high-frequency

devices.

4

• Use electromagnetic shielding, for example, shielded interface cables, when necessary.

Lightning protection

To protect the device from lightning, follow these guidelines:

• Make sure the chassis is reliably grounded by using the grounding cable.

• Make sure the grounding terminal of the AC power receptacle is reliably grounded.

• Install a lightning protector at the power input end.

Installation accessories

Power cable

(provided)

Power adapter

(provided)

Rubber feet

(provided)

Grounding

terminal

(provided)

Console cable

(provided)

Grounding

cable

(user-supplied)

Pre-installation checklist

Table 4 Pre-installation checklist

Item Re

q

uirements

Result

Installation

site

Ventilation

• There is a minimum of 10 cm (3.9 in) of clearance

around the device.

• A ventilation system is available at the installation site.

Temperature 0°C to 40°C (32°F to 104°F)

Relative humidity 5% to 95% (noncondensing)

Cleanness

• Dust concentration ≤ 3 × 10

4

particles/m

3

• No dust on desk within three days

ESD prevention

• The device is reliably grounded.

• The equipment room is dust-proof.

• The humidity and temperature are at acceptable levels.

EMI prevention

• Take effective measures to protect the power system

from the power grid system.

• Separate the protection ground of the device from the

grounding device or lightning protection grounding

device as far as possible.

• Keep the device far away from radio stations and radar

and high-frequency devices working in high current.

• Use electromagnetic shielding when necessary.

5

Item Re

q

uirements

Result

Lightning

protection

• The chassis is reliably grounded.

• The grounding terminal of the AC power receptacle is

reliably grounded.

Electricity safety

• Equip a UPS.

• In case of emergency during operation, switch off the

external power switch.

Safety

precautions

The device is far away from any moist area and heat source.

Accessories Accessories provided with the device.

Reference

• Documents shipped with the device.

• Online documents.

6

Installing the device

W

ARNING!

Keep the tamper-proof seal on a mountin

g

screw on the chassis cover intact, and if you want to open the

chassis, contact H3C Support for permission. Otherwise, H3C shall not be liable for any consequence.

Confirming installation preparations

Before you install the device, verify that you have read "Preparing for installation" carefully and the

installation site meets all the requirements.

Installation flow

Figure 1 Installation flow

7

Mounting the device on a workbench

IMPORTANT:

Do not place heavy objects on the device.

To mount the device on a workbench:

1. Place the device with bottom up and clean the round holes in the chassis bottom.

2. Attach the rubber feet to the four round holes in the chassis bottom.

3. Place the device with upside up on the workbench.

Figure 2 Mounting the device on a workbench

Grounding the device

W

ARNING!

• Correctly connecting the device grounding cable is crucial to lightning protection and EMI protection.

• Connect the grounding cable to the groundin

g

system in the equipment room. Do not connect it to a fire

main or lightning rod.

No grounding cable is provided with the device. Prepare a grounding cable yourself.

Attaching the ring terminal to the grounding cable

1. Cut the grounding cable as appropriate for connecting to the grounding strip.

2. Use a wire stripper to strip 5 mm (0.20 in) of insulation off the end of the grounding cable.

3. Slide the heat-shrink tubing onto the cable and insert the bare metal part into the end of the ring

terminal.

4. Use a crimper to secure the metal part of the cable to the ring terminal.

5. Slide the heat-shrink tubing down the cable until the tubing covers the joint.

6. Use a blow dryer to shrink the tubing around the cable.

8

Figure 3 Attaching the ring terminal to the grounding cable

Connecting the grounding cable to the device

1. Use a Phillips screwdriver to remove the grounding screw from the rear panel of chassis.

2. Use the grounding screw to attach the ring terminal of the grounding cable to the chassis.

3. Connect the other end of the grounding cable to the grounding strip.

Make sure the grounding strip has been reliably grounded.

Figure 4 Grounding the device with a grounding strip

Connecting the console cable and setting terminal

parameters

Connecting the console cable

1. Prepare a configuration terminal.

The configuration terminal can be an ASCII terminal with an RS232 serial port or a PC. The

description in this section assumes that you use a PC as the configuration terminal.

5 mm (0.20 in)

Heat-shrink

tubing

1 2

3

4

5

6

Grounding cable

Ring terminal

9

2. Connect the console cable:

a. Plug the DB-9 female connector of the console cable to the serial port of the PC.

b. Connect the RJ-45 connector to the console port of the device.

Figure 5 Connecting the console cable

NOTE:

• Identify the mark on the console port and make sure you are connecting to the correct port.

• The serial ports on PCs do not support hot swapping. To connect a PC to an operating device, first

connect the PC end. To disconnect a PC from an operating device, first disconnect the device end.

Setting terminal parameters

To set terminal parameters, for example, on a Windows 95/98/NT/2000/XP HyperTerminal:

1. Select Start > All Programs > Accessories > Communications > HyperTerminal.

The Connection Description dialog box appears.

2. Enter a name for the new connection in the Name field and click OK.

10

Figure 6 Connection description

3. Select the serial port to be used from the Connect using list, and click OK.

Figure 7 Setting the serial port used by the HyperTerminal connection

4. Set Bits per second to 9600, Data bits to 8, Parity to None, Stop bits to 1, and Flow control to None,

and click OK.

To restore the default settings, click Restore Defaults.

11

Figure 8 Setting the serial port parameters

5. Select File > Properties in the HyperTerminal window.

Figure 9 HyperTerminal window

6. On the Settings tab, set the emulation to VT100 or Auto detect and click OK.

12

Figure 10 Setting the terminal emulation in Test Properties dialog box

Connecting the Ethernet cables

Connecting a copper Ethernet port

1. Connect one end of the Ethernet cable to the copper Ethernet port on the device, and the other end

to the Ethernet port on the peer device.

2. After powering on the device, examine the LEDs of the fixed copper Ethernet port.

For more information about the LED description, see "Appendix B LEDs."

Connecting a fiber port

No transceiver module is provided with the device. The device supports only LC-type fiber connectors. For

transceiver module specifications, see "Appendix A Chassis views and technical specifications."

F

ollow these guidelines when you connect an optical fiber:

• Never stare into an open fiber port, because invisible rays might be emitted from the fiber port.

• Install dust plugs in empty fiber ports.

• Never bend a fiber excessively. The bend radius should not be less than 10 cm (3.94 in).

• Make sure the Tx and Rx ports on a transceiver module are correctly connected.

To connect the device to the network through an optical fiber:

13

1. Remove the dust plug from the fiber port.

2. Remove the dust cover from the transceiver module, and insert the transceiver module into the fiber

port.

3. Remove the dust covers from the optical fiber connector.

4. Identify the Rx and Tx ports on the transceiver module. Use the optical fiber to connect the Rx port

and Tx port on the transceiver module to the Tx port and Rx port on the peer end, respectively.

5. Power on the device, and examine the fiber port LED:

{ If the LED is on, a fiber link is present.

{ If the LED is off, no link is present. Verify that the Tx and Rx ports are correctly connected.

Figure 11 Connecting an optical fiber

Connecting the power adapter

1. Make sure the device is reliably grounded.

2. Connect the power adapter to an AC power source.

3. Connect the DC power connector on the power adapter to the power adapter receptacle on the

front panel of the device.

1 2

3

4

Page is loading ...

H3C WX2540H Installation guide

H3C WX2540H Installation guide

Related papers

Other documents