Panasonic KX-TDE200 Getting Started

Pure IP-PBX

Getting Started

for Virtual IP Cards

Thank you for purchasing a Panasonic Pure IP-PBX.

Please read this manual carefully before using this product and save this manual for future use.

KX-TDE100/KX-TDE200: PMMPR Software File Version 2.0000 or later

Model No.

KX-TDE100

KX-TDE200

2 Getting Started for Virtual IP Cards

Table of Contents

1 Before Installation .................................................................................. 3

1.1 Unpacking..........................................................................................................................4

2 Installation............................................................................................... 7

2.1 Opening/Closing the Front Cover....................................................................................8

2.2 Installing the DSP16/DSP64 Card ....................................................................................9

2.3 Inserting the SD Memory Card to the IPCMPR Card....................................................12

2.4 Installing the Power Supply Unit ...................................................................................12

2.5 Frame Earth Connection ................................................................................................13

2.6 Connecting to the LAN ...................................................................................................14

2.6.1 Connecting the IPCMPR Card to the LAN ........................................................................14

2.6.2 Connecting the IP Telephones to the LAN ........................................................................16

3 Before Programming ............................................................................ 19

3.1 Starting the PBX..............................................................................................................20

3.2 Connecting the PC..........................................................................................................21

3.3 Installing the Maintenance Console..............................................................................22

4 Programming ........................................................................................ 23

4.1 Programming the PBX ....................................................................................................24

4.1.1 Starting the Maintenance Console and Assigning the Basic Items (Quick Setup)............24

4.1.2 Installing the Virtual IP Cards to the PBX .........................................................................26

4.1.3 Installing Additional Activation Keys..................................................................................27

4.2 Programming the Virtual 16-Channel VoIP Gateway Card ..........................................29

4.2.1 Assigning the Hunt Pattern ...............................................................................................29

4.2.2 Programming the Address Translation Table.....................................................................30

4.2.3 Programming the Network Settings ..................................................................................32

4.3 Programming the Virtual Extension Card and IP Telephones ....................................37

4.3.1 Assigning the IP Addressing Information ..........................................................................37

4.3.2 Registering IP Telephones ................................................................................................49

5 Confirming the Connection ................................................................. 53

5.1 Making and Receiving Calls...........................................................................................54

Getting Started for Virtual IP Cards 3

Section 1

Before Installation

1.1 Unpacking

4 Getting Started for Virtual IP Cards

1.1 Unpacking

Check the package contents.

Main Unit × 1

CD-ROM (including manuals, etc.) × 1

Note

In this manual, the suffix of each model number (e.g., KX-TDE100NE) is omitted unless necessary.

AC Cord* × 1 Screw A

× 3 (KX-TDE100)

× 4 (KX-TDE200)

Screw B (Black)

× 2 (KX-TDE100)

× 6 (KX-TDE200)

Anchor Plug

× 3 (KX-TDE100)

× 4 (KX-TDE200)

Mini Plug (for pager and

music source) × 4

Ferrite Core (for the IPCMPR

card) × 2

SD Memory Card × 1

* The type of the AC cord may vary depending on the country/area of use.

The KX-TDE100BX/KX-TDE200BX is supplied with 2 types of AC cord. Please use whichever is

appropriate for the country/area.

In Canada, there is no ferrite core attached to the AC cord.

for KX-TDE200for KX-TDE100

Metal Bracket × 1

1.1 Unpacking

Getting Started for Virtual IP Cards 5

Necessary items (not supplied):

• Ethernet straight cables* for the LAN and PC connections.

• RJ45 connectors for the LAN and PC connections by Ethernet straight cables.

• An RS-232C cross cable for PC connection.

• Switching hubs and routers for VoIP network configuration.

* The cables should be 10BASE-T/100BASE-TX CAT 5 (Category 5) or higher cables.

1.1 Unpacking

6 Getting Started for Virtual IP Cards

Getting Started for Virtual IP Cards 7

Section 2

Installation

2.1 Opening/Closing the Front Cover

8 Getting Started for Virtual IP Cards

2.1 Opening/Closing the Front Cover

Opening the Front Cover

1. Insert a flathead screwdriver into the opening (on the left of the screw cover) and unlatch the screw

cover. Turn the screw anticlockwise to loosen.

2. Slide the front cover to the right until it stops, then lift the front cover.

Closing the Front Cover

1. Hook the front cover onto the shelf (line up the protrusions on the cover with the receptacles on the

shelf), then slide the front cover to the left until it locks.

2. Turn the screw clockwise to tighten, then secure the screw cover.

2

1

2.2 Installing the DSP16/DSP64 Card

Getting Started for Virtual IP Cards 9

2.2 Installing the DSP16/DSP64 Card

Removing the IPCMPR Card from the PBX

1. Turn the 2 screws anticlockwise to loosen them.

2. Pull the release lever in the direction of the arrow to disconnect the card from the back board. Pull the

card from the shelf to remove it.

Screws

Release Lever

Back Board

2.2 Installing the DSP16/DSP64 Card

10 Getting Started for Virtual IP Cards

Installing the DSP16/DSP64 Card

Depending on the number and the type of IP trunks and IP telephones you wish to use, required activation

keys are determined, and either the DSP16 or DSP64 card is selected to be installed.

Note

If the preinstalled activation keys on the DSP16 or DSP64 cards are not enough for the desired

configuration, refer to "4.1.3 Installing Additional Activation Keys".

DSP16: 16-channel DSP (Digital Signal Processor) card with a 4-Channel IP Trunk activation key and

an 8-Channel IP Proprietary Telephone activation key preinstalled. Compliant with ITU-T

G.729a and G.711 CODEC methods. To be mounted on the IPCMPR card.

DSP64: 64-channel DSP (Digital Signal Processor) card with four 4-Channel IP Trunk activation keys

and four 8-Channel IP Proprietary Telephone activation keys preinstalled. Compliant with

ITU-T G.729a and G.711 CODEC methods. To be mounted on the IPCMPR card.

DSP16 Card/

DSP64 Card

Screw

inside

2.2 Installing the DSP16/DSP64 Card

Getting Started for Virtual IP Cards 11

Installing the IPCMPR Card in the PBX

Install the IPCMPR card in the IPCMPR card slot of the PBX.

Note

The illustrations of the PBX shown in the installation procedure are based on the KX-TDE200.

1. Insert the card along the guide rails.

2. Holding the card as shown below, push the release lever in the direction of the arrow so that the card

engages securely with the connector on the back board.

3. Turn the 2 screws clockwise to fix the card in place.

Note

Make sure the screws are tightened to earth the card securely.

Guide Rail

Release Lever

Back Board

Screws

2.3 Inserting the SD Memory Card to the IPCMPR Card

12 Getting Started for Virtual IP Cards

2.3 Inserting the SD Memory Card to the IPCMPR

Card

The SD Memory Card contains software for all the processes of the PBX and all the customer data. The SD

Memory Card must be inserted before startup.

CAUTION

Do not remove the SD Memory Card while power is supplied to the PBX. Doing so may cause the PBX

to fail to start when you try to restart the system.

2.4 Installing the Power Supply Unit

Slot Position

Install the power supply unit (PSU) into the PSU slot.

IPCMPR Card

Example: KX-TDE200

SD

CARD

2

SD

CARD

45

SD

CARD

SD

Memory

Card

3

1

KX-TDE100 KX-TDE200

PSU Slot

Free Slots

IPCMPR Card

PSU Slot

Free Slots

IPCMPR Card

Null Slot

2.5 Frame Earth Connection

Getting Started for Virtual IP Cards 13

CAUTION

To protect the back board from static electricity, do not touch parts on the back board in the main unit,

and PSU. To discharge static electricity, touch ground or wear an earthing strap.

Installing the Power Supply Unit

1. Insert the PSU along the guide rails.

2. Push the release lever in the direction of the arrow, so that the PSU engages securely with the

connector on the back board.

3. Turn the 4 screws clockwise, in the order indicated by the numbers 1 to 4, to fix the PSU.

2.5 Frame Earth Connection

IMPORTANT

Connect the frame of the PBX to earth.

• Proper earthing (connection to earth) is very important to protect the PBX from the bad effects of

external noise or to reduce the risk to the user of electrocution in the case of a lightning strike.

• The earthing wire of the AC cable has an effect against external noise and lightning strikes, but it may

not be enough to protect the PBX. A permanent connection between earth and the earth terminal of

the PBX must be made.

1. Loosen the screw.

2. Insert an earthing wire (user-supplied)*.

3. Tighten the screw.

4. Connect the earthing wire to earth.

* For earthing wire, green-and-yellow insulation is required, and the cross-sectional area of the

conductor must be more than 0.75 mm2 or 18 AWG.

Guide Rail

Back Board

Release Lever

Screws

1

32

4

To earth

Earthing

wire

Screw

2.6 Connecting to the LAN

14 Getting Started for Virtual IP Cards

2.6 Connecting to the LAN

2.6.1 Connecting the IPCMPR Card to the LAN

Refer to the following procedure to connect the IPCMPR card to the LAN.

When the IPCMPR card is connected to the LAN for the first time, you must assign IP addressing

information to the card. Refer to "4.1 Programming the PBX" for instructions.

Note

Make sure to set the port of the switching hub that connects to the IPCMPR card to operate under "Auto

Negotiation" mode.

Attaching a ferrite core to the cable

1. Wrap the cable once around the ferrite core, leaving 3 cm between the ferrite core and the connector.

2. Close the case of the ferrite core.

Note

If you need to open the ferrite core, use a flathead screwdriver to unlatch the case.

3 cm

2.6 Connecting to the LAN

Getting Started for Virtual IP Cards 15

Connecting the IPCMPR card to a switching hub

1. Connect the cable to the LAN port of the IPCMPR card.

2. Connect the other end of the cable to the switching hub.

LAN Port

IP Softphone

SIP Extension

Ethernet Straight Cable

Router

Switching Hub

PC

IP-PT

with 2 ports

Switching Hub

2.6 Connecting to the LAN

16 Getting Started for Virtual IP Cards

2.6.2 Connecting the IP Telephones to the LAN

When an IP telephone is connected to the LAN and power is supplied for the first time, you will be prompted

to set network parameters. The network parameters must be set for the IP telephone before it can be used.

Refer to "4.3 Programming the Virtual Extension Card and IP Telephones" for instructions.

Connecting an IP Telephone to a Switching Hub

When connecting an IP telephone to the LAN, connect it to a switching hub.

Note

Since an IP softphone is installed and operates on a PC, the PC must be connected to the LAN to use

the IP softphone on the network.

The diagram below is for connecting an IP-PT to a switching hub. For SIP Extensions, refer to the

documentation of your SIP Extension.

Example: KX-NT346

Ethernet Straight Cable

To a Switching Hub

2.6 Connecting to the LAN

Getting Started for Virtual IP Cards 17

Connecting an AC Adaptor to an IP Telephone

IP-PTs and some SIP Extensions comply with the IEEE 802.3af Power-over-Ethernet (PoE) standard. If PoE

is available on your network, these IP telephones can receive the necessary power supply from the network

through the network cable. In this case, no AC adaptor is needed for the IP telephones.

However, if PoE is not available, you will need to connect an AC adaptor to the IP telephone.

Note

Use only the specified type of AC adaptor for each IP telephone. For details, refer to the documentation

of your IP telephone.

Example: KX-NT346

AC Adaptor Cord

To Wall Socket

2.6 Connecting to the LAN

18 Getting Started for Virtual IP Cards

Getting Started for Virtual IP Cards 19

Section 3

Before Programming

3.1 Starting the PBX

20 Getting Started for Virtual IP Cards

3.1 Starting the PBX

CAUTION

• SD Memory Card must be inserted in the SD Memory Card slot of the IPCMPR card before startup.

• Before touching the System Initialise Switch, discharge static electricity by touching ground or

wearing an earthing strap.

• Once you have started the PBX and if you unplug the PBX, do not perform the following procedures

to start the PBX again. Otherwise, your programmed data will be cleared.

• The PBX will continue to be powered even if the power switch is turned "OFF".

•The power supply cord is used as the main disconnect device. Ensure that the AC outlet is

located near the equipment and is easily accessible.

1. Slide the System Initialise Switch to the "SYSTEM INITIALIZE" position.

2. Plug the AC power cord into the PBX and an AC outlet, and turn on the PBX. The RUN indicator will

flash.

3. While the RUN indicator is flashing, slide the System Initialise Switch back to the "NORMAL" position.

Depending on the configuration, initialisation takes about 1 min to 3 min. If successfully executed, the

RUN indicator will stop flashing and stay lit.

All data will be cleared and the PBX will be initialised to the default values.

Note

Use only the AC power cord included with the PBX for the PSU.

System Initialise Switch

SYSTEM

INITIALIZE

NORMAL

Power

Supply Unit

RUN Indicator

To AC

Outlet

Page is loading ...

Panasonic KX-TDE200 Getting Started

This manual is also suitable for

Panasonic KX-TDE200 Getting Started

Related papers

Other documents