Hanover TRADDN5PCBN-BLU Installation guide

Brand: Hanover

Model: TRADDN5PCBN-BLU

Type: Installation guide

This manual is also suitable for



HanoverOutdoorFurniture



IMPORTANT

Ifyouhaveanyproblemswiththisproduct(missingordamagedparts,assemblyissues,etc.),

PLEASEDONOTRETURNTOTHERETAILER/STORE

fromwhereyoupurchasedtheproduct.

PleasecallourToll‐FreeCustomerServiceHotlineat:

1‐800‐416‐3511

Between9:00AMand5:00PMEasternTime,MondaythroughFriday

Orvisitourwebsiteat:

www.hanover‐products.com



Toexpediteanyfuturewarrantyclaims,pleaseretaintheInstructionSheet,Warranty

Cardandreceiptforfutureuse.

For additionalon‐linesupportonassembly,troubleshootingandcare&maintenanceofyouroutdoor

furniture,pleasevisitourwebsiteat:www.hanover‐products.com. 

6/1/2015(a)

Page 4

*NOTE:PARTSSHOWNONPARTSLISTARENOTTOSCALE

PARTS IDENTIFICATION LIST

AAF06000

PARTS LIST ORDER PART #DESCRIPTION

FOOT CAP

FACTORY ASSEMBLY

FC0030

Page 4

ASSEMBLY INSTRUCTIONS

Attach a leg connector bar to the middle leg by using the bolts and washers as shown in .

Guide the bolts through the holes in the leg connector bar, into the pre-drilled holes in the middle

leg. Repeat for the other leg connector bar.

Hand tighten only 2-3 turns.

igure

Attach a side leg to the leg connector bar by using the bolts and washers as shown in .

Guide the bolts through the holes in the leg connector bar, into the pre-drilled holes in the side leg.

Repeat for the other side leg.

Hand tighten only 2-3 turns.

igure

Attach the assembled base to the seat frame by using the bolts and washers as shown in . Guide

the bolts through the holes in the side legs and middle leg, into the pre-drilled holes in the seat frame.

Hand

tighten only 2-3 turns.

igure

After making any necessary adjustments to the alignment of the , use the hex bolt driver to tighten

all bolts. Repeat until all bolts are tight. Over tightening may strip bolts. Cover

all bolts with covers.

Do not over tighten.

ottoman

F1igure

Figure 2

Figure 3

Page 5

* NOTE: PARTS SHOWN ON PARTS LIST ARE NOT TO SCALE

PARTS IDENTIFICATION LIST

QTY

PARTS LIST DESCRIPTION ORDER PART #

AAL08045

1/4" X 20 MM BOLT

HW0036

Ø6.5 X 1.0 MM

WASHER

HW0004

FOOT CAP

FACTORY ASSEMBLY

FC0030

SEAT FRAME

SIDE LEG

HEX BOLT DRIVER

HW0006

HW0105

BOLT COVER

MIDDLE LEG

LEG CONNECTOR

BAR

AA0729

AA0730

AA0731

AA0732

Page 4

ASSEMBLY INSTRUCTIONS

Attach a leg to the leg connector bracket by carefully guiding the bolts already in place on the table legs (each leg

has two bolts) through the holes in the leg connector bracket. Add a washer and a nut to the end of each bolt

. Repeat on the other three legs.Fig. Hand tighten only. Do not tighten completely.

shown in 2

After making any necessary adjustments to the alignment of the table legs and the leg connector bracket, use the

hex bolt driver and hex wrench to tighten all nuts and bolts. each bolt and nutmust be tightened a few rev-

olutions at a time. In order to apply equal pressure to all bolt joints, we recommend working in a cross corner (X

fashion). Repeat until all bolts are tight. . Over tightening may strip bolts. Cover all nuts

and bolts with covers.

Note:

Do not over tighten

Place the table top upside down on a flat, non-abrasive surface. Attach a table leg to the table top by using the bolts

and washers as shown in . Guide bolts through holes in the table legs and into the pre-drilled holes in the table

top. Repeat for the other three legs.Hand tighten 2-3 turns only.

Fig.1

Fig.2

FOOT CAP

Page 5

*NOTE:PARTSSHOWNONPARTSLISTARENOTTOSCALE

PARTS IDENTIFICATION LIST

PARTS LIST DESCRIPTION ORDER PART #

QTY

BOLT COVER

HEX BOLT DRIVER

1/4" X 18 MM BOLT

TABLE LEG

LEG CONNECTOR

BRACKET

TABLE TOP

FC0069

HW0105

HW0004

HW0035

HW0014

HW0027

HW0009

HW0006

FOOT CAP

FACTORY ASSEMBLY

NUT COVER

HEX WRENCH

1/4" NUT

Ø6.5 X 1.0 MM

WASHER

UMBRELLA HOLE

PROTECTIVE

RING (SET)

FACTORY ASSEMBLY

G0235 & G0236

UMBRELLA POLE

STOPPER & NUT

FACTORY ASSEMBLY

G0091

& HW0448

AT71868

AT71869

AT71870

Hanover TRADDN5PCBN-BLU Installation guide

Brand: Hanover

Model: TRADDN5PCBN-BLU

Type: Installation guide

This manual is also suitable for

Download PDF

report

Hanover TRADDN5PCBN-BLU Installation guide

This manual is also suitable for

Hanover TRADDN5PCBN-BLU Installation guide

Related papers

Other documents