2. Hanover
  3. TRADDN5PCBN-SU-T
TRADDN5PCBN-SU-T

Hanover TRADDN5PCBN-SU-T, TRADDN5PCBN-SU-R Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Hanover TRADDN5PCBN-SU-T Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
HanoverOutdoorFurniture
IMPORTANT
Ifyouhaveanyproblemswiththisproduct(missingordamagedparts,assemblyissues,etc.),
PLEASEDONOTRETURNTOTHERETAILER/STORE
fromwhereyoupurchasedtheproduct.
PleasecallourToll‐FreeCustomerServiceHotlineat:
1‐800‐416‐3511
Between9:00AMand5:00PMEasternTime,MondaythroughFriday
Orvisitourwebsiteat:
www.hanover‐products.com
Toexpediteanyfuturewarrantyclaims,pleaseretaintheInstructionSheet,Warranty
Cardandreceiptforfutureuse.
For additionalon‐linesupportonassembly,troubleshootingandcare&maintenanceofyouroutdoor
furniture,pleasevisitourwebsiteat:www.hanover‐products.com.
6/1/2015(a)
Page 4
*NOTE:PARTSSHOWNONPARTSLISTARENOTTOSCALE
PARTS IDENTIFICATION LIST
AAF06000
PARTS LIST ORDER PART #DESCRIPTION
A
FOOT CAP
FACTORY ASSEMBLY
FC0030
A
Page 4
ASSEMBLY INSTRUCTIONS
1
2
C
Attach a leg connector bar to the middle leg by using the bolts and washers as shown in .
Guide the bolts through the holes in the leg connector bar, into the pre-drilled holes in the middle
leg. Repeat for the other leg connector bar.
F1
Hand tighten only 2-3 turns.
igure
D
Attach a side leg to the leg connector bar by using the bolts and washers as shown in .
Guide the bolts through the holes in the leg connector bar, into the pre-drilled holes in the side leg.
Repeat for the other side leg.
F2
Hand tighten only 2-3 turns.
igure
E
F
G
B
3
Attach the assembled base to the seat frame by using the bolts and washers as shown in . Guide
the bolts through the holes in the side legs and middle leg, into the pre-drilled holes in the seat frame.
F3
Hand
tighten only 2-3 turns.
igure
G
E
F
G
E
F
4
After making any necessary adjustments to the alignment of the , use the hex bolt driver to tighten
all bolts. Repeat until all bolts are tight. Over tightening may strip bolts. Cover
all bolts with covers.
Do not over tighten.
ottoman
F1igure
Figure 2
Figure 3
Page 5
* NOTE: PARTS SHOWN ON PARTS LIST ARE NOT TO SCALE
PARTS IDENTIFICATION LIST
QTY
PARTS LIST DESCRIPTION ORDER PART #
A
B
C
D
E
F
G
H
AAL08045
1/4" X 20 MM BOLT
HW0036
14
14
Ø6.5 X 1.0 MM
WASHER
HW0004
FOOT CAP
FACTORY ASSEMBLY
FC0030
SEAT FRAME
2
1
SIDE LEG
1
HEX BOLT DRIVER
HW0006
HW0105
BOLT COVER
14
1
MIDDLE LEG
LEG CONNECTOR
BAR
2
AA0729
AA0730
AA0731
AA0732
Page 4
ASSEMBLY INSTRUCTIONS
1
2
Attach a leg to the leg connector bracket by carefully guiding the bolts already in place on the table legs (each leg
has two bolts) through the holes in the leg connector bracket. Add a washer and a nut to the end of each bolt
. Repeat on the other three legs.Fig. Hand tighten only. Do not tighten completely.
as
shown in 2
3
After making any necessary adjustments to the alignment of the table legs and the leg connector bracket, use the
hex bolt driver and hex wrench to tighten all nuts and bolts. each bolt and nutmust be tightened a few rev-
olutions at a time. In order to apply equal pressure to all bolt joints, we recommend working in a cross corner (X
fashion). Repeat until all bolts are tight. . Over tightening may strip bolts. Cover all nuts
and bolts with covers.
Note:
Do not over tighten
Place the table top upside down on a flat, non-abrasive surface. Attach a table leg to the table top by using the bolts
and washers as shown in . Guide bolts through holes in the table legs and into the pre-drilled holes in the table
top. Repeat for the other three legs.Hand tighten 2-3 turns only.
Fig.1
Fig.1
Fig.2
FOOT CAP
A
E
G
H
B
F
E
D
C
Page 5
*NOTE:PARTSSHOWNONPARTSLISTARENOTTOSCALE
PARTS IDENTIFICATION LIST
PARTS LIST DESCRIPTION ORDER PART #
QTY
1
1
A
B
C
D
E
F
G
H
I
J
16
1
BOLT COVER
HEX BOLT DRIVER
1/4" X 18 MM BOLT
TABLE LEG
LEG CONNECTOR
BRACKET
TABLE TOP
FC0069
HW0105
HW0004
HW0035
HW0014
HW0027
HW0009
HW0006
FOOT CAP
FACTORY ASSEMBLY
4
8
8
NUT COVER
8
HEX WRENCH
1
1/4" NUT
8
Ø6.5 X 1.0 MM
WASHER
UMBRELLA HOLE
PROTECTIVE
RING (SET)
FACTORY ASSEMBLY
G0235 & G0236
UMBRELLA POLE
STOPPER & NUT
FACTORY ASSEMBLY
G0091
& HW0448
AT71868
AT71869
AT71870
Page 4
*NOTE:PARTSSHOWNONPARTSLISTARENOTTOSCALE
PARTS IDENTIFICATION LIST
AZB01405
A
B
UMBRELLA TOP
1
UMBRELLA POLE
1
PARTS LIST QTY./PCSDESCRIPTION
A
A
B
B
/