2. PAC
  3. BKNDK736

PAC BKNDK736, NDK736 User manual

  • Hello! I am an AI chatbot trained to assist you with the PAC BKNDK736 User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
CUSTOMER HELP LINE
USA 800-323-4329 • Canada 800-245-8777
Automotive Products Division
1040 Avenida Acaso • Camarillo, CA 93012, U.S.A.
USA Sales (800) 336-6500
Canada Sales (888) 922-3006 • USA Fax (805) 388-7950
For information about other American International automotive
accessories visit our website at:
http://www.americaninternational.net
NDK736 Mounting Kit
Nissan
2009-13 CUBE
2007-14 VERSA SEDAN
2007-12 VERSA HATCHBACK ( w/ Base CD Player)
2014 VERSA NOTE ( w/ Base CD Player)
VEHICLE APPLICATIONS
iNDK736
©2013 AMERICAN INTERNATIONAL INDUSTRIES, INC.
TECH Ver. 8/13 PRINT Ver. 8/13
KIT ASSEMBLY INSTRUCTIONS
NISSAN VERSA (Use factory brackets for Double DIN)
1. Starting from the front, carefully pry up on the top dash vent trim and pull forward
to remove.
2. Remove the (2) Phillips screws securing the top edge of the radio trim bezel.
3. Carefully pull the radio trim bezel forward, disconnect all attached harnesses from the
back of the radio trim bezel and remove trim bezel.
4. Remove the (4) Phillips screws securing the factory radio to the sub-dash.
5. Carefully pull the radio forward, disconnect all harnesses and antenna connector and
remove radio.
DASH DISASSEMBLY
2007-12 NISSAN VERSA HATCHBACK
2007-14 NISSAN VERSA SEDAN
1. Remove the (2) Phillips screws (with plastic rings) securing the lower edge of the
Climate Control panel.
2. Carefully unclip and lower out of the way the Climate Control panel.
3. Remove the (2) Phillips screws securing the lower edge of the Radio/Vent trim bezel
to the sub-dash.
4. Carefully pry forward and unclip the lower edge of the Radio/Vent trim bezel and then
unclip the top edge and remove the bezel.
5. Remove the (4) Phillips screws securing the radio to the sub-dash
6. Pull the radio forward, disconnect all harnesses and antenna lead and remove radio.
DASH DISASSEMBLY
2009-13 NISSAN CUBE
1. This kit is an (ISO) mounting kit only. Remove metal sleeve from radio.
2. The mounting sleeve of your new radio and trim ring cannot be used when ISO
mounting an aftermarket radio. Your radio must have a removeable trim ring.
3. Insert left and right mounting brackets to rear of kit as shown in Figure A and attach
brackets to rear of pocket with small phillips screws supplied with kit.
4. Insert ISO mountable radio between ISO mount brackets and loosely attach to sides
of radio using screws provided with radio when possible or screws supplied with kit.
5. Slide radio forward or backward for desired look and tighten screws.
IMB736 LEFT
IMB736 RIGHT
Fig A
Remove shaded tabs on
left and right bracket
(Right tab hidden in picture)
2 7
NOTES
4 5
KIT ASSEMBLY INSTRUCTIONS
2012-14 NISSAN SEDAN/ 2014 NISSAN VERSA NOTE
1. This kit is an (ISO) mounting kit only. Remove metal sleeve from radio.
2. The mounting sleeve of your new radio and trim ring cannot be used when ISO
mounting an aftermarket radio. Your radio must have a removeable trim ring.
3. Insert left and right mounting brackets to rear of kit as shown in Figure A and attach
brackets to rear of pocket with small phillips screws supplied with kit.
4. Insert ISO mountable radio between ISO mount brackets and loosely attach to sides
of radio using screws provided with radio when possible or screws supplied with kit.
5. Slide radio forward or backward for desired look and tighten screws.
IMB736 LEFT
IMB736 RIGHT
Fig D
Remove shaded tabs on
left and right bracket
(Right tab hidden in picture)
1. Carefully pry forward and unclip the Radio/Vent trim bezel and then unplug the
hazzard and airbag light (do not turn key on once unplugged). Remove panel.
2. Remove the (4) Phillips screws securing the radio to the sub-dash
3. Pull the radio forward, disconnect all harnesses and antenna lead and remove radio.
DASH DISASSEMBLY
2012-14 NISSAN VERSA SEDAN/ 2014 NISSAN VERSA NOTE
NOTES
6 3
SINGLE ISO KIT ASSEMBLY INSTRUCTIONS
NISSAN CUBE
1. This kit is an (ISO) mounting kit only. Remove metal sleeve from radio.
2. The mounting sleeve of your new radio and trim ring cannot be used when ISO
mounting an aftermarket radio. Your radio must have a removeable trim ring.
3. Insert left and right mounting brackets to rear of kit as shown in Figure B and attach
brackets to rear of pocket with small phillips screws supplied with kit.
4. Insert ISO mountable radio between ISO mount brackets and loosely attach to sides
of radio using screws provided with radio when possible or screws supplied with kit.
5. Slide radio forward or backward for desired look and tighten screws.
DOUBLE ISO/DOUBLE DIN KIT ASSEMBLY INSTRUCTIONS
NISSAN CUBE
1. Remove 3 shaded tabs on left and right Cube brackets as shown in Figure C below.
2. Insert ISO mountable radio between ISO mount brackets and loosely attach to sides
of radio using screws provided with radio when possible or hardware included with kit.
3. Slide radio component forward or backward for desired look and tighten screws.
4. Attach a rear support bracket to the rear of the new radio and adjust as necessary
to support the weight of the radio.
IMB-736 LEFT CUBE
IMB-736 RIGHT CUBE
Fig B
Fig C
For DBL ISO/DBL DIN
Remove 3 shaded tabs on
left and right bracket
(Right tab hidden in picture)
NOTES
/