PAC BKNDK786 User manual

PAC
Brand
PAC
Model
BKNDK786
Type
User manual

This manual is also suitable for

PAC BKNDK786 is a vehicle-specific dash kit for installing an aftermarket radio into select Nissan vehicles from 2007 to 2014. It allows for seamless integration of a new receiver while retaining the factory look and functionality. The kit includes ISO brackets for mounting the radio, as well as provisions for attaching the rear support for added stability. Installation involves removing unnecessary mounting tabs from the brackets, attaching the ISO brackets, sliding the radio into the kit, and securing it with the provided screws.

PAC BKNDK786 is a vehicle-specific dash kit for installing an aftermarket radio into select Nissan vehicles from 2007 to 2014. It allows for seamless integration of a new receiver while retaining the factory look and functionality. The kit includes ISO brackets for mounting the radio, as well as provisions for attaching the rear support for added stability. Installation involves removing unnecessary mounting tabs from the brackets, attaching the ISO brackets, sliding the radio into the kit, and securing it with the provided screws.

CUSTOMER HELP LINE
USA 800-323-4329 • Canada 800-245-8777
Automotive Products Division
1040 Avenida Acaso • Camarillo, CA 93012, U.S.A.
USA Sales (800) 336-6500
Canada Sales (888) 922-3006 • USA Fax (805) 388-7950
NDK786 Mounting Kit
Nissan
2007-14 VERSA SEDAN (w/BASE CD Player)
2007-12 VERSA HATCHBACK (w/BASE CD Player)
2014 VERSA NOTE (w/BASE CD Player)
2011-13 ROGUE (w/BASE CD Player)
VEHICLE APPLICATIONS
iNDK786
©2013 AMERICAN INTERNATIONAL INDUSTRIES, INC.
TECH Ver. 8/13 PRINT Ver. 8/13
KIT ASSEMBLY INSTRUCTIONS
2011-13 NISSAN ROGUE
1. Remove all unnecessary mounting tabs from both L&R brackets (Shaded below in fig.C)
2. Attach ISO brackets to the rear of the main mounting kit.
3. Slide radio into kit from rear & attach to ISO mounting brackets using screws supplied
with radio when possible or screws supplied with kit (do not tighten screws at this time).
4. Slide radio forward or backward for your desired look and then tighten the mounting screws.
5. Suggested...Attach rear support.
1. Using a panel removal tool, carefully pry the front edge of the center channel speaker
cover upward to unclip and remove from the top of the dash.
2. Remove the (4) Phillips screws securing the center channel speaker (If equipped).
3. Disconnect the center channel wire harness from the speaker and remove
speaker if equipped.
4. Carefully pry the lower side edge trim pieces from beside the Vent/Hazard assembly,
then using a panel removal tool from inside the center channel speaker area at the
top of the dash, slide the panel removal tool between the center channel speaker
mount surface, and the base beneath the center channel speaker mount surface and
pry upward on the Vent panel assembly, disconnect all harnesses from the rear of
the panel and remove assembly.
5. Using a panel removal tool, carefully pry the climate control panel forward
and lay out of the way.
6. Remove the (4) Phillips screws securing the radio to the sub-dash.
7. Carefully pull the radio forward, disconnect all wire harnesses and antenna lead
and remove radio.
DASH DISASSEMBLY
2
011-13 NISSAN ROGUE
IMB786 LEFT
IMB786 RIGHT
Fig C
Remove shaded tabs on
left and right bracket
(Right tab hidden in picture)
KIT ASSEMBLY INSTRUCTIONS
1. Starting from the front, carefully pry up on the top dash vent trim and pull forward
to remove.
2. Remove the (2) Phillips screws securing the top edge of the radio trim bezel.
3. Carefully pull the radio trim bezel forward, disconnect all attached harnesses from the back of
the radio trim bezel and remove trim bezel.
4. Remove the (4) Phillips screws securing the factory radio to the sub-dash.
5. Carefully pull the radio forward, disconnect all harnesses and antenna connector and
remove radio.
DASH DISASSEMBLY
2
007-12 NISSAN VERSA HATCHBACK
2007-11 NISSAN VERSA SEDAN
1. Remove all unnecessary mounting tabs from both L&R brackets (Shaded below in figure A)
2. Attach ISO brackets to the rear of the main mounting kit.
3. Slide radio into kit from rear & attach to ISO mounting brackets using screws supplied with radio
when possible or screws supplied with kit (do not tighten screws at this time).
4. Slide radio forward or backward for your desired look and then tighten the mounting screws.
5. Suggested...Attach rear support.
2 3
KIT ASSEMBLY INSTRUCTIONS
1. Remove all unnecessary mounting tabs from both L&R brackets (Shaded below in figure B)
2. Attach ISO brackets to the rear of the main mounting kit.
3. Slide radio into kit from rear & attach to ISO mounting brackets using screws supplied with radio
when possible or screws supplied with kit
(do not tighten screws at this time).
4. Slide radio forward or backward for your desired look and then tighten the mounting screws.
5. Suggested...Attach rear support.
1. Carefully pry forward and unclip the Radio/Vent trim bezel and then unplug the hazzard and
airbag light (do not turn key on once unplugged). Remove panel.
2. Remove the (4) Phillips screws securing the radio to the sub-dash
3. Pull the radio forward, disconnect all harnesses and antenna lead and remove radio.
DASH DISASSEMBLY
2012-14 NISSAN VERSA SEDAN / 2014 VERSA NOTE
IMB786 LEFT
IMB786 RIGHT
Fig A
Remove shaded tabs on
left and right bracket
(Right tab hidden in picture)
Fig B
IMB786 LEFT
IMB786 RIGHT
Remove shaded tabs on
left and right bracket
(Right tab hidden in picture)
  • Page 1 1
  • Page 2 2

PAC BKNDK786 User manual

PAC
Brand
PAC
Model
BKNDK786
Type
User manual
This manual is also suitable for

PAC BKNDK786 is a vehicle-specific dash kit for installing an aftermarket radio into select Nissan vehicles from 2007 to 2014. It allows for seamless integration of a new receiver while retaining the factory look and functionality. The kit includes ISO brackets for mounting the radio, as well as provisions for attaching the rear support for added stability. Installation involves removing unnecessary mounting tabs from the brackets, attaching the ISO brackets, sliding the radio into the kit, and securing it with the provided screws.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents