Metra 99-7427B is a dash kit for select Nissan Maxima models that allows for the installation of a double DIN aftermarket radio. It features a textured finish to match the factory dash and includes provisions for both DIN and ISO mount radios. The kit also includes all necessary hardware for installation.
Metra 99-7427B is a dash kit for select Nissan Maxima models that allows for the installation of a double DIN aftermarket radio. It features a textured finish to match the factory dash and includes provisions for both DIN and ISO mount radios. The kit also includes all necessary hardware for installation.
INSTALLATION INSTRUCTIONS FOR PART 99-7427
99-7427B/
99-7427G
(NON NAV MODELS)
(W/O TECH PACKAGE)
KIT FEATURES
• DIN Radio Provision With Pocket
• ISO Mount Radio Provision With Pocket
• PAINTED TO MATCH FACTORY DASH:
99-7427B=BLACK, 99-7427G=GRAY
• Textured To Match Factory Dash
• A) Radio Housing • B) Trim Plate • C) ISO Brackets • D) Module Brackets
• E) (2) Phillips Head Screws
KIT COMPONENTS
Small Flat Blade Screwdriver/ Panel Removal Tool
• Phillips Screwdriver
1-800-221-0932
© COPYRIGHT 2010 METRA ELECTRONICS CORPORATION
www.metraonline.com
A
B
C
D
E
TOOLS REQUIRED:
WIRING AND ANTENNA CONNECTIONS
(Sold Separately)
• 70-7552 - Nissan harness 2007-up
• 40-NI12 - Nissan antenna adapter 2007-up
APPLICATIONS
Nissan Maxima 2009-11
Dash Disassembly
- Nissan Maxima 2009-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Kit Preparation
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Kit Assembly
- DIN Radio Provision / ISO Mount Radio Provision With Pocket . . . . . . .3
Final Assembly
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
TABLE OF CONTENTS
99-7427
*Note:
Refer also to the instructions included with the aftermarket radio.
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
99-7427 DASH DISASSEMBLY
NISSAN MAXIMA 2009-11
(NON NAV MODELS)
(W/O TECH PACKAGE)
X
OFF
PASS
AIR
BAG
CD CHANGER
AUX IN
1
1
Unclip and remove the panel below
the radio. (
Figure B)
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
3
Unclip and remove the panel above
the radio including the a/c vents and
the climate controls. Unplug and
remove the panel. (
Figure A)
2
Remove (6) Phillips screws securing
the radio. Unplug and remove the
radio. (
Figure C)
4
Remove (5) Torx head screws secur-
ing each side bracket to factory radio
and
remove brackets and module.
(Retain brackets, module and (2)
screws from module for re-use during
kit assembly.) (
Figure D)
5
Continued on page 2.
A
B
C
D
99-7427 KIT PREPARATION
2
Attach the module brackets to the
radio housing using the (2) Phillips
head screws.
(Figure A)
1
Attach the module to the bracket/
housing assembly using the factory
Torx screws from step 5 of the dash
disassembly.
(Figure B)
2
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
A
B
NISSAN MAXIMA 2009-11
99-7427 KIT ASSEMBLY
3
Slide the DIN cage into the Radio
Housing and secure by bending the
metal locking tabs outward.
(Figure A)
1
Slide the aftermarket radio into the
cage until it snaps into place.
(Figure B)
2
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
DIN RADIO PROVISION WITH POCKET
A
B
ISO MOUNT RADIO PROVISION WITH POCKET
Mount the ISO Brackets to the after-
market radio using the screws sup-
plied with the radio.
(Figure A)
1
Slide the radio/bracket assembly into
the radio housing until it snaps into
place.
(Figure B)
2
Snap the Trim plate onto the front of
the Radio Housing.
(Figure B)
3
Continue to final assembly.
A
B
99-7427 FINAL ASSEMBLY
FINAL ASSEMBLY
FINAL ASSEMBLY
(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
A
B
C
D
Locate the factory wiring harness in the dash. Metra recommends using the proper mating
adapter and making the connections as shown. (Isolate and individually tape off the ends of
any unused wires to prevent electrical short circuit).
Re-connect the negative battery terminal and test the unit for proper operation.
Position the factory bracket/aftermarket radio assembly into the dash and secure using
the
factory hardware.
1
2
3
Secure the Double DIN radio housing to the sub dash using the factory hardware.
4
Reassemble the rest of the dash in reverse order of disassembly.
Make wiring connections using the EIA color code chart shown below and the instructions
included with the head unit. Metra recommends making connections shown below; Strip, Splice,
Solder, Tape. Isolate and individually tape off ends of any unused wires to prevent electrical short
5
4
METRA / EIA WIRING CODE
12V Ignition / Acc. . . . . . . . . . Red
12V Batt / Memory. . . . . . . . . Yellow
Ground. . . . . . . . . . . . . . . . . . Black*
Power Antenna. . . . . . . . . . . . Blue
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer . . . . . . . . . . . . . . . . . Orange / White
Right Front (+) . . . . . . . . . . . . Gray
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE:
When a Black wire is not present, ground radio to vehicle chassis. All colors may not be
present on all leads due to manufacturer’s specifications.
NOTES
5
99-7427
99-7427 INSTRUCTIONS
1-800-221-0932
REV. 09/15/10 © COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION INST99-7427
www.metraonline.com
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Metra 99-7427B is a dash kit for select Nissan Maxima models that allows for the installation of a double DIN aftermarket radio. It features a textured finish to match the factory dash and includes provisions for both DIN and ISO mount radios. The kit also includes all necessary hardware for installation.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Metra 99-9301 User manual
-
Metra 95-7427B User manual
-
Metra 99-7511S User manual
-
-
-
Metra 99-2007 Specification
-
-
-
Metra 99-7876 Installation guide
-
Other documents
-
Metra Electronics 99-7337B User manual
-
Metra Electronics 95-7416G User manual
-
Metra Electronics 997416 User manual
-
Metra Electronics 99-8225G User manual
-
Metra Electronics 99-8225G User manual
-
Metra Electronics 99-5822B User manual
-
Metra Electronics 99-9223 User manual
-
Metra Electronics 99-9100 User manual
-
Metra Electronics 99-9100 User manual
-
Metra Electronics 99-7426 User manual
