ITC HMTLVVKK-LLLWL-10 User manual

Brand: ITC

Model: HMTLVVKK-LLLWL-10

Type: User manual

ITC HMTLVVKK-LLLWL-10 is a flexible LED light designed for various applications requiring customizable lighting solutions. It features a bendable light strip that allows for easy installation on curved or irregular surfaces. The light is available in RGBW (red, green, blue, and white) options, providing color-changing capabilities. It operates on a constant voltage power supply of 13.6V DC or 24V DC and requires a compatible RGBW controller (sold separately) for color customization. The light strip can be cut to the desired length, making it suitable for various project sizes.

3030 Corporate Grove Dr.

Hudsonville, MI 49426

Phone: 616.396.1355

itc-us.com

Safety Instructions

• Disconnect power before installing, adding or changing any component.

• To avoid a hazard to children, account for all parts and destroy all packing materials.

• Do not install any luminaire assembly closer than 6” from any combustible materials.

1. Determine installation location and drill a hole in the mounting surface. Make sure to accommodate the driver box if using RGBW

ﬂex light.

Installation Considerations For All Flexible Lighting Products

• Do not bend lighting more than necessary. Refer to page two for bend radius minimums.

• Only bend the LED ribbon in one natural direction, do not try to bend in an unnatural direction such as twisting.

**Installation Considerations For HMTL Flexible Lighting

• Unroll the entire length of HMTL before installing.

• Start installation at the wire lead end.

• When installing the light on the mounting surface, make sure to push towards the wired end.

• Do not use any roller as that may cause damage to the LED circuit.

• Each RGBW ﬂex light length will include a driver that prevents the RGB LED and white LED from turning on at the same time. Care should be taken during installation to accom-

modate the size of the driver box (see dimensional drawing below).

PARTS / TOOLS NEEDED:

Application Speciﬁc

Sealant

Flex Light & Mounting Clips Power Drill

(not provided)

#6 pan head screws

(not provided) (not provided) Butt Splices

(not provided)

2. Secure clips to mounting surface using

#6 pan head screws (not provided).

3. Feed the wires into the hole and apply

application speciﬁc sealant* around the

hole and wires.

*Sealant here

*Clip spacing is dependant on application, when

going around curves clip spacing should be closer.

4. Secure the light in the track by gently

pushing into clips

*HMTL ﬂexible lighting cannot be ﬁeld cut. Field cutting the light will void the warranty.

Driver Box (applies to RGBW only)

2” 1”Ø

INSTALLATION INSTRUCTIONS

Wander™ Flex Light

Part#: HMTLVVKK-LLLWL-10

For warranty information please visit www.itc-us.com/warranty-return-policy

DOC #: 710-00114 • Rev D • 06/

Page 1 of 2

3030 Corporate Grove Dr.

Hudsonville, MI 49426

Phone: 616.396.1355

itc-us.com

5.04

4.33

R20.0" MIN

DESIGN STATE:

INSTALLATION INSTRUCTION

Do not twist tapelight

ALWAYS INSTALL WIRE END FIRST!

CAUTION

MINIMUM BEND RADIUS

LATERAL BEND

R0.562" MIN

TOP TO BOTTOM BEND

5. Follow the wiring diagram below to wire the light to your system.

HMTL Flex Light

Red (+)

Black (-)

Green (G)

Neutral (N)

Load (L)

To 110V - 277V

Power

Positive (+)

Negative (-)

Constant Voltage

Class 2 Power Supply

13.6 V DC or 24V DC

Red (-)

White (-)*

Green (-)

Blue (-)

Red (+) Black (-)

Constant Voltage

Class 2 Power Supply

13.6V DC or 24V DC

HMTL Flex Light

RGBW

Controller

sold separately

Green (G)

Neutral (N)

Load (L)

Black (+)

*Note the RGB lights will not have a white wire

ITC HMTLVVKK-LLLWL-10 User manual

ITC HMTLVVKK-LLLWL-10 User manual

ITC HMTLVVKK-LLLWL-10 User manual

Related papers

Other documents