ITC Wander Flex Light Installation guide

Type
Installation guide

ITC Wander Flex Light offers versatile lighting solutions for various applications. With its flexible design, it can be effortlessly shaped to fit curved surfaces or unique architectural features. Installation is a breeze, thanks to the included mounting clips and application-specific sealant. The light emits a bright and consistent glow, making it ideal for task lighting, accent lighting, or ambient lighting. It operates on a 12V DC power supply, ensuring energy efficiency and compatibility with a wide range of systems.

ITC Wander Flex Light offers versatile lighting solutions for various applications. With its flexible design, it can be effortlessly shaped to fit curved surfaces or unique architectural features. Installation is a breeze, thanks to the included mounting clips and application-specific sealant. The light emits a bright and consistent glow, making it ideal for task lighting, accent lighting, or ambient lighting. It operates on a 12V DC power supply, ensuring energy efficiency and compatibility with a wide range of systems.

3030 Corporate Grove Dr.
Hudsonville, MI 49426
Phone: 616.396.1355
itc-us.com
Safety Instructions
• Disconnect power before installing, adding or changing any component.
• To avoid a hazard to children, account for all parts and destroy all packing materials.
• Do not install any luminaire assembly closer than 6” from any combustible materials.
5. Follow the wiring diagram below to wire the light to your system.
1. Determine installation location and
drill a hole in the mounting surface.
Installation Considerations For All Flexible Lighting Products
• Do not bend lighting more than necessary. Refer to page two for bend radius minimums.
• Only bend the LED ribbon in one natural direction, do not try to bend in an unnatural direction such as twisting.
**Installation Considerations For HMTL Flexible Lighting
• Unroll the entire length of HMTL before installing.
• Start installation at the wire lead end.
• When installing the light on the mounting surface, make sure to push towards the wired end.
• Do not use any roller as that may cause damage to the LED circuit.
PARTS / TOOLS NEEDED:
Application Specific
Sealant
Flex Light & Mounting Clips Power Drill
(not provided)
#6 pan head screws
(not provided) (not provided) Butt Splices
(not provided)
HMTL Flex Light
Black (+)
Red (R)
12V DC (+)
Black (-)
Incoming
12V DC
Power
Fuse
2. Secure clips to mounting surface
using #6 pan head screws
(not provided).
3. Feed the wires into the hole and apply
application specific sealant* around the
hole and wires.
*Sealant here
*Clip spacing is dependant on application, when
going around curves clip spacing should be
closer.
4. Secure the light in the track by
gently pushing into clips
*HMTL flexible lighting cannot be field cut. Field cutting the light will void the warranty.
12V Wiring
Red (-)
White (-)*
Green (-)
Blue (-)
Red (+) Black (-)
Incoming
12V DC
Power
HMTL Flex Light
RGBW
Controller
sold separately
Black (+)
*Note the RGB lights will not have a white wire
INSTALLATION INSTRUCTIONS
Wander Flex Light
Part#: HMTLVVKK-LLLWL-10
For warranty information please visit www.itc-us.com/warranty-return-policy
DOC #: 710-00114 • Rev C • 08/20/20
Page 1 of 2
3030 Corporate Grove Dr.
Hudsonville, MI 49426
Phone: 616.396.1355
itc-us.com
5.04
4.33
R20.0" MIN
DESIGN STATE:
INSTALLATION INSTRUCTION
Do not twist tapelight
ALWAYS INSTALL WIRE END FIRST!
CAUTION
MINIMUM BEND RADIUS
LATERAL BEND
R0.562" MIN
TOP TO BOTTOM BEND
5 Cont. Follow the wiring diagram below to wire the light to your system.
HMTL Flex Light
Red (+)
Black (-)
Green (G)
Neutral (N)
Load (L)
To 110V - 277V
Power
Positive (+)
Negative (-)
Constant Voltage
Class 2 Power Supply
13.6 V DC or 24V DC
Red (-)
White (-)*
Green (-)
Blue (-)
Red (+) Black (-)
Constant Voltage
Class 2 Power Supply
13.6V DC or 24V DC
HMTL Flex Light
RGBW
Controller
sold separately
Green (G)
Neutral (N)
Load (L)
Black (+)
*Note the RGB lights will not have a white wire
For warranty information please visit www.itc-us.com/warranty-return-policy
DOC #: 710-00114 • Rev C • 08/20/20
Page 2 of 2
  • Page 1 1
  • Page 2 2

ITC Wander Flex Light Installation guide

Type
Installation guide

ITC Wander Flex Light offers versatile lighting solutions for various applications. With its flexible design, it can be effortlessly shaped to fit curved surfaces or unique architectural features. Installation is a breeze, thanks to the included mounting clips and application-specific sealant. The light emits a bright and consistent glow, making it ideal for task lighting, accent lighting, or ambient lighting. It operates on a 12V DC power supply, ensuring energy efficiency and compatibility with a wide range of systems.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI