2. Porter
  3. FAM-KEY SWITCH ASSEMBLIES

Porter FAM-KEY SWITCH ASSEMBLIES, SPORTSONIC II RECEIVER- AUX. KEY SWITCH CONTROL Operating instructions

  • Hello! I've reviewed the Installation and Maintenance Guide for the Porter Key Switch Control System, model XELE007911xx. This document describes the wiring and installation process for this key switch system and highlights the importance of using two keys to prevent sudden winch reversals. I am ready to answer any questions you have about the system or its installation.
  • What is the purpose of the two keys provided with the key switch?
    What type of wall box is required for mounting the key switch?
    What is a recommended distance between a winch and a junction box ?
    What should I do if up and down labels do not correspond to winch movement?
Copyright p2021 by Litania Sports Group, Inc. All rights reserved.
XELE007911xx - KEY SWITCH CONTROL SYSTEM
INSTALLATION AND MAINTENANCE GUIDE
6/4/21
INST00178019
800-637-3090
www.porterathletic.com
ELECTRICAL CONTRACTOR
TO MOUNT 4" SQUARE
JUNCTION BOX WITHIN
3'-0" OF WINCH LOCATION
6'-0" Lg. SJO CORD WITH
TWIST-LOCK TYPE
PLUG - FROM WINCH
4 POLE TWIST-LOCK
RECEPTACLE MOUNTED
IN 4" SQUARE JUNCTION
BOX COVER (BY PORTER)
"A"
INDIVIDUAL KEY SWITCH MOUNTED IN A STANDARD 412" SQUARE FLUSH-MOUNTED
STAINLESS STEEL COVER PLATE FOR MOUNTING IN A 4" SQUARE x 312" DEEP MASONRY
BOX (RACO No. 696 OR EQUAL) BY ELECTRICAL CONTRACTOR.
MOMENTARY KEY
SWITCH FURNISHED
WITH TWO KEYS (UP
AND DOWN) TO
PREVENT THE
POSSIBILITY OF
INSTANTANEOUS
REVERSING OF THE
WINCH, WHICH
COULD RESULT IN
OVERRIDING THE
LIMIT SWITCHES,
OR PLACING UNDUE
STRESS ON HOIST
SYSTEM. DO NOT
SEPARATE KEYS
FROM EACH OTHER.
OPERATOR NOTE
To raise equipment, insert UP key and turn LEFT.
To lower equipment, insert DOWN key and turn to
RIGHT. Watch equipment until it comes to a
complete stop.
BEFORE OPERATING THIS EQUIPMENT, CLEAR
THE FLOOR AREA AROUND AND BENEATH THE
EQUIPMENT, AS PERSONAL INJURIES ARE
POSSIBLE DUE TO ENTRAPMENT OR
CAUTION
EQUIPMENT FAILURES.
OFF
UP
DOWN
CAUTION
KEY SWITCH MUST
BE MOUNTED ON THE
WALL IN A LOCATION
SO THAT THE
EQUIPMENT IT IS
CONTROLLING IS IN
FULL VIEW OF THE
OPERATOR.
WIRING AT WINCH
WIRING AT WALL MOUNTED KEY SWITCH
Key Switch Control System - XELE007911xx
Copyright p2021 by Litania Sports Group, Inc. All rights reserved.
6/4/21
INST00178019
1 Key Switch, 2 Gang Box
XELE00791112 = 1 Backstop
XELE00791212 = 2 Backstops
2 Key Switches, 4 Gang Box
XELE00791122 = 2 Backstops
XELE00791222 = 4 Backstops
3 Key Switches, 6 Gang Box
XELE00791132 = 3 Backstops
XELE00791232 = 6 Backstops
AVAILABLE
GANGED
KEY SWITCHES
4 Key Switches, 8 Gang Box
XELE00791142 = 4 Backstops
XELE00791242 = 8 Backstops
5 Key Switches, 10 Gang Box
XELE00791152 = 5 Backstops
XELE00791252 = 10 Backstops
6 Key Switches, 12 Gang Box
XELE00791162 = 6 Backstops
XELE00791262 = 12 Backstops
Field Note - If ganged
plate requirement is not
specified, the individual
key switch assembly will
be provided.
Porter recommends the
use of "double" gang
spacing (as illustrated) per
single switch, to provide
adequate clearance for
wiring within the electrical
box.
Individual Key
Switch Assembly
Supplied As
Standard
OFFUP DOWN
OFFUP DOWN OFFUP DOWN
OFFUP DOWN
OFFUP DOWNOFFUP DOWN
GANGED KEY SWITCH ASSEMBLIES ARE
AVAILABLE - SPECIFY QUANTITIES (SEE TABLE
BELOW FOR WALL BOX SIZE REQUIREMENTS -
DIMENSION "A").
KEY
SWITCH
QTY.
334"
1
2
3
4
5
6
"A"
BOX
WIDTH
738"
11"
1458"
1814"
2178"
RACO
MASONRY
BOX No.
(Or Equal)
696
698
965
N/A
N/A
N/A
RACO
GANGABLE
BOX No.
(Or Equal)
592
592
592
592
592
592 Qty. 12
Qty. 10
Qty. 8
Qty. 6
Qty. 4
Qty. 2
ELECTRICIAN NOTE: IF
EQUIPMENT OPERATION
DOES NOT CORRESPOND
TO UP AND DOWN LABEL
ON KEY SWITCH, REVERSE
BLACK AND RED WIRES.
RED (DOWN)
BLACK (UP)
Y
X
GREEN (GROUND)
BACKSIDE OF
RECEPTACLE
(TYPICAL)
HOT LINE
WHITE
TERMINALS: 14" QUICK-CONNECT TYPE.
MATING TERMINALS PROVIDED BY
ELECTRICAL CONTRACTOR.
TOP VIEW
OF
KEY SWITCH
The minimum wire size is dependent on the
motor voltage, motor full-load amperage rating,
and the TOTAL distance from the circuit
breaker panel to the winch receptacle. Consult
VOLTAGE DROP CALCULATION TABLES to
determine the minimum wire size.
HOT LINE
115 VOLT, SINGLE PHASE,
60 HERTZ POWER SOURCE
PROTECTED BY A 20 AMP
CIRCUIT BREAKER
CHAMPAIGN, ILLINOIS 61822
IN QUALITY SPORTS EQUIPMENT
www.porterathletic.com
601 MERCURY DRIVE
WORLD LEADER
SAVE THESE INSTRUCTIONS FOR FUTURE USE
IMPORTANT NOTE - PERFORMANCE OF WINCH
IS BASED ON 115 VOLTS AT MOTOR
TERMINALS. VOLTAGES LESS THAN 115
VOLTS WILL AFFECT HOISTING CAPACITY AND
RESULT IN DAMAGE TO MOTOR, THUS
VOIDING WARRANTY. SUBSTITUTION OF THIS
KEY SWITCH WILL VOID ALL WARRANTIES AND
WILL RENDER THE OPERATION OF
BACKSTOPS / CURTAINS UNSAFE.
XELE007911xx - KEY SWITCH CONTROL SYSTEM
INSTALLATION AND MAINTENANCE GUIDE
WARNING: This product can expose you to Vinyl Chloride,
which is known to the State of California to cause cancer.
For more information go to www.p65warnings.ca.gov.
!
D
/