Page is loading ...
Halle Upholstered Daybed and Trundle
Dark Brown
4019257
WARNING
infants and babies must not sleep on this bed for safety reasons. To prevent injury and damage to this unit, PROHIBIT jumping on it.
IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
STOP
DO NOT RETURN PRODUCT TO THE
STORE
Individual stores do not stock parts.
If a part is missing or damaged, call our
toll-free customer service line. We will
gladly ship your replacement parts FREE
of charge.
Need Parts or Assistance?
PARTS:DAYBED
A
BACK REST
T926240
x 1
FRONT RAIL 01
T926250
x 1
LEFT ARMREST
T926270
x 1
FRONT/REAR RAIL
T926280
x 2
CENTER BRACE
T926290
x 1
LEFT BRACKET
T393050
x 3
END CAP 01
T393130
x 4
U
B
C
D
S
T
RIGHT BRACKET
T393060
x 3
RIGHT ARMREST
T926260
x 1
E
F
K
U
U
REAR BRACE
T926300
x 1
V
V
X
Y
Z
O
Note: "U""V" have been pre-assembled on "E""K",
they are available for replacement.
SINGLE SLAT CAP
T926370
x 26
DOUBLE SLAT CAP
T926380
x 13
LEG
T926310
x 4
END CAP 02
T920510
x 2
V
WOODEN SLATS
T926360
x 26
4 / 35
A
B
C
D
T
E
F
Y
K
X
Z
PARTS:TRUNDLE
FRONT PANEL
T926320
x 1
SIDE RAIL
T926330
x 2
W
END CAP 03
T393100
x 4
G
H
I
J
O
Note: "W" has been pre-assembled on "H", it is
available for replacement.
REAR RAIL
T926340
x 2
FRONT RAIL 02
T926350
x 1
WOODEN SLATS
T926360
x 24
SINGLE SLAT CAP
T926370
x 24
DOUBLE SLAT CAP
T926380
x 12
X
Y
CASTER
T393000
X 2
LOCKING CASTER
T392990
X 2
P
N
W
G
H
I
O
J
Y
5 / 35
P
N
NOTE:
Please do not completely tighten any hardware, until the
entire assembly is complete.Once completed, please be
sure to properly tighten all the hardware.
HARDWARE PACK:DAYBED
HEX KEY
4mm
X 1
4
BOLT
1/4"X 3/4"
x 6
1 2 3
BOLT
1/4" X 1 3/16"
x 34
6 / 35
BOLT
1/4" X 1 9/16"
x 14
HARDWARE PACK:TRUNDLE
HEX KEY
4mm
X 1
WRENCH 01
X 1
NOTE:
Please do not completely tighten any hardware, until the
entire assembly is complete.Once completed, please be
sure to properly tighten all the hardware.
1
4
5
BOLT
1/4" X 1 3/8"
x 6
BOLT
1/4"X 1 9/16"
X 6
2
NUT
1/4"
x6
3
WRENCH 02
X 1
6
7 / 35
NOTE: The following instructions will illustrate how to assemble the Daybed from Step 1 to Step 10. Please use the Daybed Hardware
Pack:T4019257A-00 .
1.1 Attach (Z) to (C,D);
1.2 Screw BOLT (2) to (C,D), don't completely tighten.
Z
C
D
NOTE: To avoid fraying the fabric during assembly,
please lay the armrests (C,D) on a piece of cardboard.
2
2
2
2
2
NOTE: Please remove the protective plastic
cap on the tip of thread before assembling.
2.1 Attach (T) to (B) with BOLT (1);
2.2 Attach (S) to (B) with BOLT (1).
1
T
B
B
1
S
B
T
S
2
2
A
A
A
4
3
11 / 35
3
B
B
Attach (E) to (B) with BOLT (3).
E
2
S
B
B
D
C
A
C
2
T
A
C
2
Attach (F) to (C,D) with BOLT (2), then properly tighten all the BOLTS.
C
2
C
F
D
NOTE: Holes on part (F)
should be facing upward.
F
K
D
C
K
C
3
Attach (K) to (C,D) with BOLT (3).
9
16 / 35
10
17 / 35
10.1
10.2
10.3
O
Y
F
O
Y
H
H
I
I
I
J
3
1
3
NOTE: Holes on part (H) should
be facing upward.
NOTE: Slat holes on part (I,J)
should be facing downward.
N
N
H
H
H
P
5
5
J
I
2
/
