Dorel Home DE99242 Installation guide

DO NOT RETURN TO THE STORE !

Visit www.dhpfurniture.com/eng/support-home

or call Toll-Free 1-800-267-1739

4107119

B34410711900 - 10125-M

Date of Purchase

Emily Upholstered Bed

E.L. - 2016-08-22

If parts are missing or damaged, we will gladly ship your

replacement parts free of charge.

Lot Number

Thank you for purchasing from DHP!

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY

INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.

1

Twin

Vanilla Faux Leather

Weight Limit: 225 Lb / 102 Kg

TM

Contact Us!

cs@dhpfurniture.com

DHP

410E, First Street South, Wright City, MO 63390, USA

Attention: Consumer Service.

Read Before Beginning Assembly

1-800-267-1739

Monday - Friday, 9:00 am - 5:00 pm (Eastern Time)

Warranty Information

2

B34410711900

Caution

DHP warrants this product to be free from defects in material and workmanship and

agrees to remedy any such defect. This warranty covers one year from the date of

original purchase. This is solely limited to the repair or replacement of defective

parts and assembly labor is not included.

This warranty does not apply to any product which has been improperly assembled,

subjected to misuse or abuse or which has been altered or repaired in any way.

Liability for consequential damages is excluded to the extent exclusion is permitted

by law. This warranty gives you specific legal rights and you may also have other

rights which vary from state to state.

To obtain warranty service, purchaser must present original bill of sale. Components

repaired or replaced are warranted through the remainder of the original warranty

period only. The defective components will be repaired or replaced without charge,

subject to the terms and conditions described above.

Visit www.dhpfurniture.com to view the limited warranty valid in the U.S. and

Canada.

 Call our toll free number if you need assistance.

 Work in a spacious area and near where the unit will be used, preferably on a

carpet, or use a piece of the cardboard packaging to protect your floor and product.

 Recommended # of people needed for assembly: 2 (however it is always better

to have an extra hand). Estimated assembly time is 2 hours.

 Make sure all parts are included. Most parts are labeled or stamped on the raw

edge.

 Read each step carefully. It is very important that each step of the instructions is

performed in the correct order. If these steps are not followed in sequence,

assembly difficulties will occur.

 This product is designed for home use and not intended for commercial use.

 This product contains small components. Please ensure that they are kept away

from small children.

 Do not use power tools to assemble your furniture. Power tools may strip or

damage the parts.

For help with assembly, identifying parts, product information or to order parts,

please contact us:

Page is loading ...

4

Parts

B34410711900

All in 1 big box!

Before you throw the package, please use the

Check Box to identify the parts and ensure that

you have all the parts needed for the assembly.

There are inner box(es) that include components

required to complete this assembly.

Replacement Parts, Visit www.dhpfurniture.com/eng/support-home

A

B

A1

C

D

J

I

H

G

F

O

N

M

L

K

Side Panel 01

T941520

X 2

Side Panel 02

T941530

X 2

Headboard

T941490

X 1

Fabric Back Panel

T941500

X 1

Footboard

T941510

X 1

Center Rail 02

T926710

X 1

Center Rail 01

T926700

X 2

Side Rail 02

T926680

X 4

Side Rail 01

T926670

X 2

Side Rail 03

T926690

X 2

Wooden Slats

T926760

X 24

Corner Bracket

T393110

X 4

Support Leg 02

T926660

X 2

Support Leg 01

T926730

X 2

Cross Brace

T926720

X 1

S

T

X

Y

Z

Left Bracket

T393080

X 2

Right Bracket

T393090

X 2

Single Slat Cap

T926370

X 24

Double Slat Cap

T926380

X 12

Leg

T941540

X 4

A

B

C

D

C

D

F

G

H

Z

L

I

J

M

K

I

T

S

N

X

Y

O

5

Hardware Pack

B34410711900

Hardware Pack #: T4107119-00

Hardware Note:

Please do not completely tighten all the hardware,

until the entire assembly is complete, unless

otherwise indicated in the step-by-step

instructions.

6

7

8

4

5

3

2

1

1/4" X 3/4"

X 40

1/4" X 1 3/8"

X 6

1/4" X 1 9/16"

X 28

1/4" X 1 3/4"

X 3

5/16" X 2 1/4"

X 4

4mm

X 1

Wrench

X 1

1/4"

X 3

AU

6

B34410711900

Step

1

The slat holes on part (F)

should be facing upward.

Attach (F)&(H) to (C)&(D) with BOLT 3.

Repeat the same step for remaining parts

(C/D/F/H).

X 16

3

C

F

3

D

H

C

F

AV

7

B34410711900

Step

2

The slat holes on part (G)

should be facing upward.

X 12

3

Attach (G) x 2 to (C)&(D) with BOLT 3.

Repeat the same step for remaining parts

(G).

C

D

G

D

G

3

AW

AY

8

B34410711900

Step

3

X 12

1

Attach (S) to (D) and (T) to (C)with BOLT 1.

Repeat the same step for the other

subassembly (C) & (D).

C

D

S

T

C

1

G

D

S

T

G

9

B34410711900

Step

4

Stick (A1) to the back of (A) with Velcro as

illustrated.

A1

A

BA

BB

10

B34410711900

Step

5

Screw BOLTS 2 into (A) and BOLTS 1 into

(B), leave half of the bolts exposed.

1

X 4

2

1

B

A

B

2

1

Do not completely tighten the BOLTS 1

and 2, leave half of the thread exposed.

2

X 4

BC

11

B34410711900

Step

6

Hang (C) & (D) on (A) & (B) as illustrated,

don't completely tighten the BOLTS until

STEP 10 is complete.

A

C

D

C

B

T

C

A

2

12

B34410711900

Step

7

Attach (N) to (Z) with BOLT 5.

Repeat the same step for remaining legs

(Z).

X 4

5

Z

N

5

BD

BE

13

B34410711900

Step

8

8.1 Attach (N) x 4 to (A,B,C & D) with

BOLTS 1;

8.2 Attach (L) x 2 to (H) with BOLTS 2.

X 2

2

X 16

1

8.1

8.2

1

Z

N

A

C

2

H

L

D

C

D

L

H

A

N

Z

L

BF

14

B34410711900

Step

9

Holes on part (I & J) should be facing upward.

1

X 4

Insert (I) x 2 & (J) into (M) x 2, then fix

them with BOLTS 1.

I

M

J

I

J

I

M

15

B34410711900

Step

10

Attach subassembly from previous STEP to

(A) and (B) with BOLTS 1, then properly

tighten all the Bolts.

1

X 4

A

I

A

I

BJ

16

B34410711900

Step

11

Attach (K) to (F) x 2 & (J) with BOLTS 4

and NUTS 6.

X 3

4

X 3

6

4

F

K

F

7

8

J

6

BK

BT

BU

17

B34410711900

Step

12

12.1

12.2

12.3

X

O

F

G

X

O

Y

A

G

I

A

X

Y

O

I

12.1 Insert (O) into (X);

12.2 Press (X) into (F&G), repeat the

same procedure for the opposite side.

12.3 Insert both ends of slats (O) into (Y),

then press (Y) into (I&J) as illustrated.

Repeat the same procedures going

backwards for every row of slats.

J

I

G

18

Helpful Hints

B34410711900

 Move your new furniture carefully, with two

people lifting and carrying the unit to its new

location.

 Your DHP furniture can be disassembled and

reassembled to move.

 Some parts have been pre-assembled for this

item. They are illustrated on this page and available

for replacement.

WARNINGS:

For safety reasons and to prevent injuries:

 This bed is not intended for use by children under 4

years old.

 Prohibit jumping and horseplay on this bed.

 Only use a mattress which is 74" - 75" long and 37

1/2" - 38 1/2" wide.

 Do not use risers under this bed.

Helpful Hints

Weight Limit: 225 Lb / 102 Kg

END CAP 01

T393120

X 2

END CAP 02

T392520

X 2

Page is loading ...

Dorel Home DE99242 Installation guide

Dorel Home DE99242 Installation guide

in other languages

Related papers

Other documents