EtherWAN EL2211 Series Quick Installation Guide

Brand
EtherWAN
Model
EL2211 Series
Category
Network switches
Type
Quick Installation Guide
W70G-EL2211V22 Page 1
Installation Guide
EL2211 Series | Media Converter
Copyright 2023 EtherWAN Systems, Inc. All Rights Reserved 03/27/2023
1 Unpacking
Open the carton and unpack the items. Your package
should include an EL2211 media converter and a
power adaptor. If items are missing or damaged,
notify your EtherWAN representative.
Download the full manual at:
https://www.etherwan.com
2 Select Installation Location
Wall mounting installation is supported. Place the
equipment where it will not be subjected to extreme
temperatures, humidity, or electromagnetic
interference. Specifically, the site you select should
meet the following requirements:
▪ The ambient temperature should be between 32
and 122 degrees Fahrenheit (0 to 50 degrees
Celsius).
▪ The relative humidity should be less than 95
percent, non-condensing.
▪ Surrounding electrical devices should not exceed
the electromagnetic field (RFC) standards for IEC
801-3, Level 2 (3V/M) field strength.
▪ Make sure that the equipment receives adequate
ventilation. Do not block the ventilation holes on
each side of the equipment.
Chassis Installation
The converter can be installed into any of the
expansion slots in a compatible chassis.
▪ Install the converter onto a carrier supplied with
the chassis:
▪ Unscrew the carrier from the desired expansion
slot on the chassis.
▪ Fit the converter onto the carrier, and insert the
carrier to the guide rails of the expansion slot.
▪ Tighten the retaining screws to fix the carrier in
the chassis.
3 Connect Power
This Converter is a plug-and-play device. Connect
the supplied AC to DC power adaptor to the
receptacle on the rear panel of the converter, and
then attach the plug into a standard AC outlet.
Ensure to connect the power cord to a socket outlet
with earthing connection if supplied by Class I power
supply or power source.
4 Ports and Port Settings
The EL2211 provides one 10/100/1000BASE TX port
and one 1000BASE-SX/LX/BX port.
This device complies with IEEE802.3 10Base-Te,
IEEE802.3u 100Base-TX, IEEE802.3ab 1000Base-T, and
IEEE802.3z 1000Base-SX/LX.
5 DIP Switches
There are six pins on the DIP switch for port settings.
Refer to the table below.
No.
Down
1
Disable LFPT (link-
fault-pass-through)
2
Enable auto
negotiation for TX
port
3
TX port forced to
full duplex mode
4
TX port forced to
100Mbps
5
Store-and-forward
mode
6
Function reserved
Function reserved
All six dip switches are “Down” as default setting.
W70G-EL2211V22 Page 2
Installation Guide
EL2211 Series | Media Converter
Copyright 2023 EtherWAN Systems, Inc. All Rights Reserved 03/27/2023
Disconnect the converter from the power source
before changing any of the DIP switch settings.
Link-Fault-Pass-Through (LFPT):
LFPT allows network operators to stay aware of
network connection status. If a link fails, the function
will disable the link on the other side, therefore
notifying the connected device of the link failure.
Store-and-forward mode:
The device begins to forward a frame only after
completely receiving the frame and passing a CRC
check.
Converter mode:
The device begins to forward a frame as soon as the
frame header is received.
NOTE: In order for converter mode to work, both TX
and FX must be set to the same speed.
Otherwise, the device will automatically switch to
store-and-forward mode.
6 LED Indicators
The LED indicators give you instant feedback on status
of the converter:
LED
State
Indication
PWR
Steady
Power on
Off
Power off
LFPT
Steady
LFPT function enabled
Off
LFPT function disabled
LNKC
Steady
Copper valid network
connection established
Flashing
Transmitting or receiving data
Off
No connection
G:GE
A:100
Steady
Green: Copper Connection at
1000Mbps
Amber: Copper Connection at
100Mbps
Off
Copper Connection at 10Mbps
LNKF
Steady
Fiber valid network connection
established
Flashing
Transmitting or receiving data
Off
No connection
FDX
Steady
Copper Link at Full-duplex
mode
Off
Copper Link at Half-duplex
mode
CLASS 1 LASER PRODUCT
Each laser product complies with US FDA regulations
of 21 CFR 1040.10 and 1040.11 or complies with those
regulations except for deviations pursuant to Laser
Notice No. 56 dated May 8, 2019.
Manufacturer information:
EtherWAN Systems, Inc.
33F, No. 93, Sec. 1, Xintai 5th Rd., Xizhi Dist., New
Taipei City, 221 Taiwan
The full product manual can be downloaded from:
www.etherwan.com
  • Page 1 1
  • Page 2 2

EtherWAN EL2211 Series Quick Installation Guide

Brand
EtherWAN
Model
EL2211 Series
Category
Network switches
Type
Quick Installation Guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents