EtherWAN EL1032T Series Quick Installation Guide

Brand
EtherWAN
Model
EL1032T Series
Category
Electrical wallplates
Type
Quick Installation Guide

EtherWAN EL1032T Series is a media converter that provides one TX port and one FX port. The TX port uses an RJ-45 connector. The converter supports IEEE802.3af and IEEE802.3at power input, providing power to the connected device. The Link-Fault-Pass-Through function allows network operators to stay aware of network connection status. If a link fails, the function will disable the link on the other side, therefore notifying the connected device of the link failure. Port settings are made by means of a DIP (Dual Inline Package) switch at the rear panel of the module.

EtherWAN EL1032T Series is a media converter that provides one TX port and one FX port. The TX port uses an RJ-45 connector. The converter supports IEEE802.3af and IEEE802.3at power input, providing power to the connected device. The Link-Fault-Pass-Through function allows network operators to stay aware of network connection status. If a link fails, the function will disable the link on the other side, therefore notifying the connected device of the link failure. Port settings are made by means of a DIP (Dual Inline Package) switch at the rear panel of the module.

W70G-EL1032TQ1 Page 1
Installation Guide
EL1032T Series | Media Converter
Copyright 2023 EtherWAN Systems, Inc. All Rights Reserved 03/27/2023
1 Unpacking
Open the carton and unpack the items. Your package
should include an EL1032T media converter and this
Quick Install Guide. If items are missing or damaged,
notify your EtherWAN representative.
Download the full manual at:
https://www.etherwan.com
2 Select Installation Location
Place the equipment where it will not be subjected to
extreme temperatures, humidity, or electromagnetic
interference. Specifically, the site you select should
meet the following requirements:
▪ The ambient temperature should be between -10
and 60 degrees Celsius (14 to 140 degrees
Fahrenheit).
▪ The relative humidity should be less than 95
percent, non-condensing.
▪ Make sure that the equipment receives adequate
ventilation. Do not block the ventilation holes on
each side of the equipment.
3 Connect Power
There are two power inputs for this device, a 3-pin
terminal block and a 4-pin latched DC jack.
Input voltage on the terminal block is:
48~52VDC for IEEE802.3af (15.4W)
52~57VDC for IEEE802.3at
Input voltage for latched DC jack is:
48VDC +/- 10%
4 Ports and Port Settings
The converter provides one TX port and one FX port.
The TX port uses RJ-45 connector.
Port settings are made by means of a DIP (Dual Inline
Package) switch at the rear panel of the module.
5 DIP Switch Settings
DIP
Switch
ON
1
Enable forced
mode for TX port
2
TX port forced to
10Mbps
3
TX port forced to
half duplex mode
4
Enable Link-Fault-
pass-Through
* LFPT=Link Fault Pass Through
Link-Fault-Pass-Through allows network operators to
stay aware of network connection status. If a link fails,
the function will disable the link on the other side,
therefore notifying the connected device of the link
failure.
W70G-EL1032TQ1 Page 2
Installation Guide
EL1032T Series | Media Converter
Copyright 2023 EtherWAN Systems, Inc. All Rights Reserved 03/27/2023
6 LED Indicators
LED
State
Indication
Power 1/2
Steady
Power on
Off
Power off
PoE
Steady
Powered device is
connected
Off
Powered device is
disconnected
Link/ACT
FX and TX
Steady
Valid network connection
established
Flashing
Transmitting or receiving
data
Off
No valid network
connection or data
transmission
Manufacturer information:
EtherWAN Systems, Inc.
33F, No. 93, Sec. 1, Xintai 5th Rd., Xizhi Dist., New
Taipei City, 221 Taiwan
The full product manual can be downloaded from:
www.etherwan.com
  • Page 1 1
  • Page 2 2

EtherWAN EL1032T Series Quick Installation Guide

Brand
EtherWAN
Model
EL1032T Series
Category
Electrical wallplates
Type
Quick Installation Guide

EtherWAN EL1032T Series is a media converter that provides one TX port and one FX port. The TX port uses an RJ-45 connector. The converter supports IEEE802.3af and IEEE802.3at power input, providing power to the connected device. The Link-Fault-Pass-Through function allows network operators to stay aware of network connection status. If a link fails, the function will disable the link on the other side, therefore notifying the connected device of the link failure. Port settings are made by means of a DIP (Dual Inline Package) switch at the rear panel of the module.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents