SMART Furniture Locks
Instruction Manual
tuya Temporary Password trigger condition,
tuya APP generated temporary password,
there will be a command to be issued,
in the lock press 9 # Temporary Password Command,
can use the normal use of the temporary password
Semiautomatic installation diagram
1. front paneI
2. connecting pipe
3. silicone pad
4. Fangxin
5. lock cylinder
6. lock body
7. Rear panel
8. Indoor locking knob
9. battery cover
10. Screw-fitting
Long press the back lock setting key,
the countdown is over in 5 seconds
release and restore the factory
setting successfully
Note: When installing semi-automatic lock, adjust the clutch
and direction of handle according to the direction of door opening.
Note: Initialization password is: 123456, or any fingerprint can unlock the lock.
1. Initialization
Press the set button (rear panel button) for 5seconds.
Voice will remind: Initialization successfully.
Semi-automatic operation instructions
Note: The first 9 unlock information are taken as the administrator users.
All unlock information are at most 300pcs.
Note: After the normally open mode is turned on, every unlocking is normally open mode,
and the lock will not be automatically closed,
so it is necessary to manually unlock the lock once.
2. Add administrator information
( Up to three administrator users )
3. Add General User Information
4. Delete unlock information
5. Normally unlock mode
Input 2 enter into delete users mode,
voice prompt "please
enter the delete code
Voice prompt "Please
verification administrator
information"
Click touch panel - press "*" - press " # "
After verification scucessfully,
voice prompt"
1. add users
2. Delete the user,
3. Door lock function,
4. Add an administrator user
Input 1 enter into the add users mode
voice prompt "please enter the unlock
information" (system will add
automatically in sequence)
Voice prompt "Please
verification administrator
information"
In the initialization state
To wake up the screen press
"* # "
Click touch panel - press "*" - press " # "
After verification scucessfully,
voice prompt"
1. add users
2. Delete the user,
3. Door lock function,
4. Add an administrator user
Voice prompt "Please add
administrator information"
(administrator can be fingerprint
password or ic card)
When add successfully, voice
prompt "add administrator
successfully"(can continuously
add 9times )
Input 3, voice prompt "normally
open mode turned on" or "normally
open mode turned off"
Voice prompt "Please
verification administrator
information"
Click touch panel - press "*" - press " # "
After verification scucessfully,
voice prompt"
1. add users
2. Delete the user,
3. Door lock function,
4. Add an administrator user
Installation diagram of fully automatic lock
Installation Step Instructions
1. First install the lock body, with M5 * 6 screws (4)
fixed lock body;
2. Install the lock core and fix it with the lock screw.
Ensure that the copper bar of the lock shaft
Facing the interior, the length is 18 ~ 20mm long
(as shown in Figure 2).
Install the lock core and then cut the copper strip).
3. Mounting front panel.
4. Install the base plate (with adhesive cushion),
fix the two studs of the front panel with M5 screws.
5. Connect the front and back panel data cable,
and then install the back panel on a good hole
position, with M4 screw Wire 4 fixed.
6. Install the lithium battery, cover the battery cover
and install it. (Figure 2)
The lock core rod is
exposed out of
the door plane.
18mm-20mm
Voice prompt "Please
verification administrator
information"
After verification successfully,
voice prompt
Select 1 to enter the door lock function,
press 3 to enter door lock settings,
press 4 to enter more settings, and
press three to restore factory settings
Click touch panel - press "*" -
press " # "
1. Motor
2. Rotation time
3. Set close time
4. Autolock
Press 3 to enter
the installation settings
1.Local setting
2.App Setting
3.Install
3. Door lock installation function debugging (optional)
2. Enter the system to resume the initialization operation (optional)
Fully automatic lock operating instructions
1. Enter the maintenance menu by pressing 888 # in the initial state
2. Press * # enter administrator to enter the system interface and
select the installation settings
Remove the battery cover,
press the rear lock setting key for 5 seconds to
end the countdown, release the setting key to
restore the factory settings successfully
Back lock setting key
Note: Initialization password is: 123456, or any fingerprint can unlock the lock.
1. Initialization
Press the set button (rear panel button) for 5seconds.
Voice will remind: Initialization successfully.
Note: The first 9 unlock information are taken as the administrator users.
All unlock information are at most 300pcs.
Five minutes continuous input wrong password more than 5 times,
the keyboard locked 90s, 90s system does not respond to any operation,
can be set by the back panel to enter the administrator to lift.
Password anti-peep function:
Password Enter the password in the following manner when opening the door:
XXX Password; You can add some irrelevant code before and after the password,
and then press # to confirm. The password must be included in the entry.
Each operation more than 12 seconds without operating action system will
automatically exit When the voltage is lower than 6.9V,
the alarm will be automatically given every time the lock is unlocked.
After the alarm, the back door lock can be unlocked for 200 times.
If the number is over, it will be forbidden to unlock.
Be sure to replace the new battery before unlocking times.
4. Add administrator information
( Up to three administrator users )
5. Add General User Information
6. Delete unlock information
7. Other description
In the initialization state
To wake up the screen press
"* # "
Voice prompt "Please add
administrator information"
(administrator can be fingerorint
password or ic card)
When add successfully, voice
prompt "add administrator
successfully" (can continuously
add 9times )
Press 2 Door lock function settings
Input 2 enter into delete users mode,
voice prompt "please
enter the delete code
Voice prompt "Please
verification administrator
information"
Click touch panel - press "*" -
press " # "
Press 2 Door lock function settings
Press 1 to add user
(can add fingerprint, password,
credit card)
Voice prompt "Please
verification administrator
information"
Click touch panel - press "*" -
press " # "
1.Fully automatic lock distribution network mode:
* # Enter the system entry management, press the * key to return, press 1 wireless
settings to add distribution network
2.In the semi-automatic network mode:
the door lock needs to record an administrator user. After the APP enters the search
page, tap the back lock setting key to add the distribution network.
Doodle APP download installation and
door lock distribution network (2. 4G)
Remarks:
How to use Tuya APP to open the door remotely,
There is a doorbell lock, ringing the doorbell on the lock will send instructions to Tuya APP,
There is no doorbell lock, pressing 9# on the lock will send instructions to Tuya APP,
Tuya, after receiving the instruction, the main page will pop up to request remote door
opening. Click it to authorize remote door opening.
How to use the temporary password of Tuya APP After the temporary password is generated
in the Tuya APP, an instruction is issued. Press 9 # on the lock can be issued, APP pull down
refresh display in use, you can use the temporary password
semi-automatic
Tap the rear
lock setting key
Sweep
Cipher key
Card identification
area
External Doorbell
key
Fingerprint
identification area
Emergency key
USB emergency
power supply
Emergency key
USB emergency
power supply
External Doorbell
key
Fingerprint
identification area
Card identification
area
Cipher key
Automatic slide cover
sensing area (optional)
Functional Menu schematic
/
