1
For assistance with assembly contact:
Southern Enterprises Inc.
Customer Service 1-800-633-5096
www.seidal.com
MS904700TX/4800TX
TV Media Stand-
Cullerton Black/
Off White
2
Care and Cleaning Instructions:
Before using, wipe with a clean , dry cloth.
Periodically apply furniture wax to renew
The nish. Avoid rubbing or scratching the
surface with rough or abrasive objects.
For replacement parts or questions, please
call Customer Service at 1-800-633-5096.
Do not return product to store. Please call
manufacturer for assistance, questions or
parts.
MS904700TX/4800TX
TV Media Stand- Cullerton Black/ Off White
Assembly Instructions
Please review all parts and hardware before disposing of any packaging.
Call Customer Service if missing hardware. Do not return to store/retailer.
Using a screw that is too long will cause damage.
Before beginning assembly, separate each type of screw. Carefully study
the screw diagrams below. You may receive extra hardware with your unit.
※
MAX. LOADING CAPACITY IS 175 LBS FOR TOP PANEL, 20 LBS FOR FIXED SHELF,
15 LBS PER ADJUSTABLE SHELF.
a.
Wood Dowel
∅
6mmx25mm
d.
Cam Lock
∅
15mmx9mm
f.
Metal Plate
16mmx10mm
b.
Cam Lock Dowel
∅
6.2mmx32mm
e.
Screw
∅
3mmx16mm
i.
Knob Bolt
∅
4mmx16mm
j.
Screw
∅
3mmx14mm
g.
Pin
∅
6mmx19mm
c.
Screw
∅
4mmx25.4mm
h.
Knob
∅
27mmx24mm
Quantity
Of 27
Quantity
Of 20
Quantity
Of 7
Quantity
Of 20
Quantity
Of 31
Quantity
Of 3
Quantity
Of 12
Quantity
Of 8
Quantity
Of 8
Quantity
Of 3
Tool required: Phillips screw driver
(Not Included)
3
For assistance with assembly contact:
Southern Enterprises Inc.
Customer Service 1-800-633-5096
www.seidal.com
CAM LOCK INSTRUCTION:
THIS ITEM IS ASSEMBLED WITH CAM LOCK SET.
--SCREW CAM LOCK DOWEL INTO PANEL II.
--INSERT CAM LOCK INTO PRE-DRILLED HOLE IN PANEL I, AND
--ROTATE CAM LOCK UNTIL ARROW IS IN LINE WITH HOLE ON PANEL EDGE.
--ALIGN CAM LOCK DOWEL TO CAM LOCK HOLE ON PANEL I, AND PRESS
PANELS I & II TOGETHER.
--LOCK PANELS TOGETHER BY TURNING CAM LOCK CLOCKWISE UNTIL
TIGHT.
NOTE :
FOLLOW INSTRUCTIONS LISTED BELOW IN THE PROPER SEQUENCE AS NUMBERED TO ASSURE
FAST, EASY AND CORRECT ASSEMBLY. HOUSE HOLD GLUE SUGGESTED FOR WOOD DOWEL.(eg.
ELMERS GLUE, NOT PROVIDED).SOLID ARROW MARK POINTS AT FRONT SIDE OR UP DIRECTION.
PHILLIP SCREW DRIVER IS REQUIRED(NOT PROVIDED).TWO PERSONS ARE RECOMMENDED TO
ASSEMBLE THIS ITEM.
CAM LOCK
CAM LOCK DOWEL
PANEL EDGE
PANEL II
PANEL I
CAM LOCK INSTRUCTION
PARTS LIST:
NO DESCRIPTION QTY NO DESCRIPTION QTY
A
Bottom Panel
1 J
Right Side Back Panel
1
B
Base Support
1 K
Center Upper Back Panel
1
C
Middle Left Panel
1 L
Center Lower Back Panel
1
D
Middle Right Panel
1 M
Left Side Panel
1
E
Center divider
1 N
Adjustable shelf
2
F
Left Side Panel
1 O
Left Glass Door
1
G
Right Side Panel
1 P
Center Wooden Door
1
H
Top Panel
1 Q
Right Glass Door
1
I
Front cross Brace
1
MS904700TX/4800TX
TV Media Stand-
Cullerton Black/
Off White
4
Step 1:
Insert wood dowels (a) into
the bottom base (A). Join
the base support (B) and the
bottom base (A) with screws
(c) as shown in Figure 1.
Step 2:
Insert cam lock dowels (b)
to the bottom panel (A),
also the middle left and right
panels (C) and (D) as shown
in Figure 1.
Customer Service 1-800-633-5096
Southern Enterprises, Inc.
600 Freeport Pkwy Ste: 200
Coppell, Texas 75019
Figure 1
MS904700TX/4800TX
TV Media Stand- Cullerton Black/ Off White
Assembly Instructions
5
Step 1:
Assemble the middle left
and right panels (C) and
(D) and the center divider
(E) using wood dowels (a).
Tighten cam lock dowels (b)
with cam locks (d) from the
pre-drilled hole as shown in
Figure 2.
Step 2:
Assemble middle and side
panels (F) (C) (D) and (G)
with bottom panel (A) using
wood dowels (a), and tighten
cam lock dowel (b) with cam
lock (d) from the pre-drilled
hole as shown in Figure 2.
Figure 2
MS904700TX/4800TX
TV Media Stand- Cullerton Black/ Off White
Assembly Instructions
6
Step 1:
Join the front cross brace (I)
to the top panel (H) using
wood dowels (a), and tighten
using screws (c). Insert cam
lock dowels (b) into the top
panel (H) as shown in Figure
3.
Step 2:
Join the top panel (H) to
the assembly from Figure
2 using wood dowels, and
tighten cam lock dowels (b)
with cam locks (d) from the
pre-drilled holes as shown in
Figure 3.
Figure 3
MS904700TX/4800TX
TV Media Stand- Cullerton Black/ Off White
Assembly Instructions
7
Step 1:
Tighten the back panels (K)
(L) (M) (J) to the assembly
using screws (e) through the
metal plate (f) as shown in
Figure 4.
Figure 4
MS904700TX/4800TX
TV Media Stand- Cullerton Black/ Off White
Assembly Instructions
8
Step 1:
Insert the pins (g) at the
desired position and place
the adjustable shelves (N)
above the pins as shown in
Figure 5.
Step 2:
Tighten the door panels (O)
(P) and (Q) to the assembly
using screws (j) through the
pre-xed hinges.
Step 3:
Tighten knobs (g) to the door
panels (O) and (Q) using
knob bolts (i) through the
pre-drilled holes.
Figure 5
MS904700TX/4800TX
TV Media Stand- Cullerton Black/ Off White
Assembly Instructions
9
CAUTION
The top shelf is intended for a at screen television with a maximum
overall width of 50” and supports up to 175 lb.
The top shelf is NOT INTENDED for tube televisions.
Each center shelf should not be loaded with more than 20 lb. Each side
shelf should not be loaded with more than 15 lb.
DO NOT EXCEED RECOMMENDED LOAD. Use with products heavier than the
maximum sizes and weights indicated may result in instability causing
possible injury.
This unit contains a permanent warning sticker located on back panel.
Do not allow children under 16 years to move the cart.
Model: MS9047/800TX
Cullerton TV/Media Stand
Southern Enterprises, Inc
600 Freeport Parkway,
Suite 200 Coppell, Texas, 75019
Manufacture Date: 10/15/2013
10
Parts Replacement Form
Customer Information
Name
Address
City/State/Zip Code
Phone Number
Please indicate where you purchased this item: Store/Website/Catalog
Please indicate color/size/style number:
Style No Parts Letter Parts Description Quantity Needed
Please immediately examine this product carefully. Any request for missing parts or damage replacement
must be received within 90 days of your receipt of the product. Replacement, if available, will be
honored within this time frame. Parts will not be available for items arriving fully assembled. We do
not recommend modifying product(s) and we are not responsible for any damages due to product
modication(s). If damages or missing parts are not reported within 90 days of your receipt, we are under
no obligation to provide parts or replacement merchandise.
Please contact Southern Enterprises at 800-633-5096 or in Dallas 972-869-0111/ 9am – 4pm Mon-Fri
Central time if you have product issues or email us at [email protected]. Please ask for customer
service representative for issues involving damages or replacement parts. Please ask for technical
assistance representative for any issues with product and assembly/construction.
Please contact the retailer that you purchased from for returns.
Customer Service
1-800-633-5096
Southern Enterprises, Inc.
600 Freeport Parkway, Suite 200
Coppell, Texas 75019
/
