For assistance with assembly contact:
Southern Enterprises Inc.
Customer Service 1-800-633-5096
service@seidal.com
www.seidal.com
TORRES DESK
HO270500TX-BLACK
Assembly Instructions
PO#11906
A Quantity
of 45
CAM BOLT（￠6.5*35mm）
B Quantity
of 41
WOOD DOWEL（￠8*30mm）
C Quantity
of 45
CAM LOCK（￠14.8*11.5mm）
D Quantity
of 2
HEXAGON SOCKET BOLT（￠5/16”*1-1/8”）
E Quantity
of 2
SPRING WASHER（￠5/16”）
F Quantity
of 2
FLAT WASHER（￠5/16”*16mm）
G Quantity
of 1
ALLEN WRENCH（5mm）
H Quantity
of 1
STOPPER（L55*W16mm）
I Quantity
of 8
FLAT HEAD LONG SCREW（#8*25mm）
J Quantity
of 1
FLAT HEAD SHORT SCREW（￠3*12mm）
TORRES DESK
Parts List
Please review all parts and hardware before disposing of any packaging.
Call Customer Service if missing hardware. Do not return to store/retailer.
Using a screw that is too long will cause damage.
Before beginning assembly, separate each type of screw. Carefully study the
screw diagrams below . You may receive extra hardware with your unit.
K Quantity
of 45
COVER（￠16mm）
(1) Quantity
of 1
TOP PANEL
(2) Quantity
of 1
LEFT SIDE PANEL
(3) Quantity
of 1
MIDDLE VERTICAL PANEL
(4) Quantity
of 1
RIGHT SIDE PANEL
(5) Quantity
of 1
VERTICAL PANEL
(6) Quantity
of 1
FRONT PANLE
(7) Quantity
of 1
BACK PANEL
(8) Quantity
of 1
UPPER SHELF PANEL
(9) Quantity
of 1
LOWER SHELF PANEL
(10) Quantity
of 1
BASE
(11) Quantity
of 1
CROSS BAR
(12) Quantity
of 1
CONNECTION PANEL
(13) Quantity
of 1
DRAWER FRONT PANEL
(14) Quantity
of 2
DRAWER SIDE PANEL
(15) Quantity
of 1
DRAWER BACK PANEL
(16) Quantity
of 1
DRAWER BOTTOM PANEL
TORRES DESK
Parts List
Please review all parts and hardware before disposing of any packaging.
Call Customer Service if missing hardware. Do not return to store/retailer.
Using a screw that is too long will cause damage.
Before beginning assembly, separate each type of screw. Carefully study the
screw diagrams be
low . You may receive extra
hardware with your unit.
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Periodically apply furniture wax to renew
the finish . Avoid rubbing or scratching the
surface with rough or abrasive objects.
For replacement parts or questions, please
Call Customer Service at 1-800-633-5096
Do not return product to store, please call
Manufacturer for assistance, questions or
Parts.
Assembly Tool Required
No.2 Phillips Screwdriver (Not Included)
Figure 1
INSERT CAM LOCKS(C) INTO
PREDRILLED HOLES ON LOWER SHELF
PANEL (9). SCREW CAM BOLT(A) INTO
PREDRILLED HOLES ON VERTICAL
PANEL (5). ATTACH LOWER SHELF
PANEL (9) TO VERTICAL PANEL (5) BY
SLIPPING WOOD DOWEL(B) & CAM
BOLT(A) INTO CORRESPONDING
PREDRILLED HOLES UNTIL LOWER
SHELF PANEL (9) & VERTICAL PANEL
(5) MEET. SECURE BY ROTATING CAM
LOCK (C) COUNTERCLOCKWISE WITH
PHILLIPS SCREWDRIVER.
Figure 2
INSERT CAM LOCKS(C) INTO
PREDRILLED HOLES ON ASSEMBLED
UNIT IN THE STEP 1. SCREW CAM
BOLT(A) INTO PREDRILLED HOLES ON
FRONT PANEL (6).
ATTACH ASSEMBLED UNIT IN THE STEP 1
TO FRONT PANEL (6) BY SLIPPING WOOD
DOWEL(B) & CAM BOLT(A) INTO
CORRESPONDING PREDRILLED HOLES
UNTIL FRONT PANEL (6) & ASSEMBLED
UNIT IN THE STEP 1 MEET. SECURE BY
ROTATING CAM LOCK (C)
COUNTERCLOCKWISE WITH PHILLIPS
SCREWDRIVER.
TORRES DESK
Assembly Instructions
B
C
C
Figure 3
INSERT CAM LOCKS(C) INTO
PREDRILLED HOLES ON ASSEMBLED
UNIT IN THE STEP 2. SCREW CAM
BOLT(A) INTO PREDRILLED HOLES ON
UPPER SHELF PANEL (8). ATTACH
ASSEMBLED UNIT IN THE STEP 2 TO
UPPER SHELF PANEL (8) BY SLIPPING
WOOD DOWEL(B) & CAM BOLT(A) INTO
CORRESPONDING PREDRILLED HOLES
UNTIL UPPER SHELF PANEL (8)) &
ASSEMBLED UNIT IN THE STEP 2 MEET.
SECURE BY ROTATING CAM LOCK (C)
COUNTERCLOCKWISE WITH PHILLIPS
SCREWDRIVER.
Figure 4
INSERT CAM LOCKS(C) INTO
PREDRILLED HOLES ON RIGHT
SIDE PANEL (4). SCREW CAM
BOLT(A) INTO PREDRILLED HOLES
ON ASSEMBLED UNIT IN THE STEP
3. ATTACH RIGHT SIDE PANEL (4)
TO ASSEMBLED UNIT IN THE STEP
3 BY SLIPPING WOOD DOWEL(B) &
CAM BOLT(A) INTO
CORRESPONDING PREDRILLED
HOLES UNTIL RIGHT SIDE PANEL
(4) & ASSEMBLED UNIT IN THE
STEP 3 MEET. SECURE BY
ROTATING CAM LOCK (C)
COUNTERCLOCKWISE WITH
PHILLIPS SCREWDRIVER.
TORRES DESK
Assembly Instructions
Figure 5
INSERT CAM LOCKS(C) INTO
PREDRILLED HOLES ON
ASSEMBLED UNIT IN THE STEP 4.
SCREW CAM BOLT(A) INTO
PREDRILLED HOLES ON BACK
PANEL (7). ATTACH BACK PANEL (7)
TO ASSEMBLED UNIT IN THE STEP
4 BY SLIPPING WOOD DOWEL(B) &
CAM BOLT(A) INTO
CORRESPONDING PREDRILLED
HOLES UNTIL BACK PANEL (7) &
ASSEMBLED UNIT IN THE STEP 4
MEET. SECURE BY ROTATING CAM
LOCK (C) COUNTERCLOCKWISE
WITH PHILLIPS SCREWDRIVER.
USE FLAT HEAD SHORT SCREW (J) TO
ATTACH STOPPER (H) & CROSS BAR (11)
TOGETHER.
INSERT CAM LOCKS(C) INTO
PREDRILLED HOLES ON CROSS BAR (11).
SCREW CAM BOLT(A) INTO PREDRILLED
HOLES ON ASSEMBLED UNIT IN THE
STEP 5. ATTACH CROSS BAR (11) TO
ASSEMBLED UNIT IN THE STEP 5 BY
SLIPPING WOOD DOWEL(B) & CAM
BOLT(A) INTO CORRESPONDING
PREDRILLED HOLES UNTIL CROSS BAR
(11) & ASSEMBLED UNIT IN THE STEP 5
MEET. SECURE BY ROTATING CAM LOCK
(C) COUNTERCLOCKWISE WITH PHILLIPS
SCREWDRIVER. INSERT CAM LOCKS(C)
INTO PREDRILLED HOLES ON MIDDLE
VERTICAL PANEL (3). SCREW CAM
BOLT(A) INTO PREDRILLED HOLES ON
ASSEMBLED UNIT. ATTACH ASSEMBLED
UNIT TO MIDDLE VERTICAL PANEL (3) BY
SLIPPING WOOD DOWEL(B) & CAM
BOLT(A) INTO CORRESPONDING
PREDRILLED HOLES UNTIL ASSEMBLED
TORRES DESK
Assembly Instructions
Figure 6
UNIT & MIDDLE VERTICAL PANEL (3)
MEET. SECURE BY ROTATING CAM LOCK
(C) COUNTERCLOCKWISE WITH PHILLIPS
SCREWDRIVER.
Figure 7
INSERT CAM LOCKS(C) INTO
PREDRILLED HOLES ON
ASSEMBLED UNIT IN THE STEP 6.
SCREW CAM BOLT(A) INTO
PREDRILLED HOLES ON BACK BASE
(10). ATTACH BASE (10) TO
ASSEMBLED UNIT IN THE STEP 6 BY
SLIPPING WOOD DOWEL(B) & CAM
BOLT(A) INTO CORRESPONDING
PREDRILLED HOLES UNTIL BASE
(10) & ASSEMBLED UNIT IN THE
STEP 6 MEET. SECURE BY
ROTATING CAM LOCK (C)
COUNTERCLOCKWISE WITH
PHILLIPS SCREWDRIVER.
INSERT (18) INSERT TO THE
INSERT CAM LOCK(C) INTO
PREDRILLED HOLES ON
CONNECTION PANEL (12).
SCREW CAM BOLT(A) INTO
PREDRILLED HOLES ON ASSEMBLED
UNIT IN THE STEP 7. ATTACH
CONNECTION PANEL (12)) TO
ASSEMBLED UNIT IN THE STEP 7 BY
SLIPPING WOOD DOWEL(B) & CAM
BOLT(A) INTO CORRESPONDING
PREDRILLED HOLES UNTIL
CONNECTION PANEL (12) &
ASSEMBLED UNIT IN THE STEP 7
MEET. SECURE BY ROTATING CAM
LOCK (C) COUNTERCLOCKWISE
TORRES DESK
Assembly Instructions
Figure 8
WITH PHILLIPS SCREWDRIVER.
ATTACH LEFT SIDE PANEL (2) TO
ASSEMBLED UNIT BY SLIPPING
WOOD DOWEL(B) INTO
CORRESPONDING PREDRILLED
HOLES UNTIL LEFT SIDE PANEL(2)
& ASSEMBLED UNIT MEET. USE
ALLEN WRENCH (G) & HEXAGON
SOCKET BOLT (D) & SPRING WASHER
(E) & FLAT WASHER (F) CONNECT
LEFT SIDE PANEL (2) & ASSEMBLED
UNIT TOGETHER.
Figure 9
INSERT CAM LOCKS(C) INTO
PREDRILLED HOLES ON
ASSEMBLED UNIT IN THE STEP 8.
SCREW CAM BOLT(A) INTO
PREDRILLED HOLES ON TOP PANEL
(1). ATTACH TOP PANEL (1) TO
ASSEMBLED UNIT IN THE STEP 8 BY
SLIPPING WOOD DOWEL(B) & CAM
BOLT(A) INTO CORRESPONDING
PREDRILLED HOLES UNTIL TOP
PANEL (1) & ASSEMBLED UNIT IN
THE STEP 8 MEET. SECURE BY
ROTATING CAM LOCK (C)
COUNTERCLOCKWISE WITH
PHILLIPS SCREWDRIVER.
USE FLAT HEAD LONG SCREW (I)
TO CONNECT DRAWER SIDE
PANELS (14) & DRAWER FRONT
PANEL (13) & DRAWER BOTTOM
PANEL (16) & DRAWER BACK PANEL
(15) TOGETHER.
TORRES DESK
Assembly Instructions
Figure 10
Figure 11
Stick covers (K) to the cam locks
(C) surface.
PUSH DRAWER INTO ASSEMBLED
UNIT IN THE STEP 10.
Figure 12
NOW YOUR NEW DESK IS READY
TO USE.
Please immediately examine this product carefully. Any request for missing parts or damage replacement must
be received within 90 days of your receipt of the product. Replacement, if available, will be honored within this
time frame. Parts will not be available for items arriving fully assembled. We do not recommend modifying
product(s) and we are not responsible for any damages due to product modification(s).
If damages or missing
parts are not reported within 90 days of your receipt, we are under no obligation to provide parts or replacement
merchandise.
Please contact Southern Enterprises at 800-633-5096 or in Dallas 972-869-0111/ 9am – 4pm Mon-Fri Central
time if you have product issues or email us at service@seidal.com. Please ask for customer service
representative for issues involving damages or replacement parts. Please ask for technical assistance
representative for any issues with product and assembly/construction.
Please contact the retailer that you purchased from for returns.
Customer Information
Name
Address
City/State/Zip Code
Phone Number
Please indicate where you purchased this item: Store/Website/Catalog
Please indicate color/size/style number:
Style No Parts Letter Parts Description Quantity Needed
Parts Replacement Form
Customer Service 1-800-633-5096
service@seidal.com
Southern Enterprises, Inc.
600 Freeport Parkway, Suite 200
Coppell, Texas 75019
CAUTION
Max weight capacity for the desk is 60 lb.
Each center shelf should not be loaded with more than 20 lb. Each side shelf should not be loaded
with more than 20 lb.
DO NOT EXCEED RECOMMENDED LOAD. Use with products heavier than the
weights indicated may result in instability causing possible injury.
This unit contains a permanent warning sticker located on under side of top shelf.
Do not allow children under 16 years to move the cart.
Model: HO270500TX
TORRES DESK
Southern Enterprises, Inc
600 Freeport Parkway, Suite 200
Coppell, Texas, 75019
Manufacture Date:
/
