FA902900TX-Ebony Stain
Stockton Media Fireplace
Assembly Instructions
For assistance with assembly, contact:
Southern Enterprises Inc.
Customer Service 1-800-633-5096
www.seidal.com
Stockton Media Fireplace
Parts List
Please check packaging for all parts and hardware before discarding. Unpack and lay parts on clean, padded
surface like carpet or blanket. Check that you have all parts indicated. Call customer service if hardware is
missing. Before beginning assembly, carefully study the diagrams below and sort your hardware according to
the pictures. Using the incorrect hardware will cause damage.
A Quantity
of 24
Cam Bolt
B Quantity
of 24
Wood Dowel (￠8*30mmL)
C Quantity
of 24
Cam Lock
D Quantity
of 12
Bolt
E Quantity
of 12
Half Nut
F Quantity
of 1
2
Hex Nut
G Quantity
of 1
Wrench
H Quantity
of 1
Firebox （In Separate Carton）
I Quantity
of 2
Screw(
￠8*1”L)
J Quantity
of 1
Anti-Tipping Hardware
1 Quantity
of 1
Top Panel
2 Quantity
of 2
Middle Side Panel
3 Quantity
of 1
Middle Shelf Panel
4 Quantity
of 1
Bottom Panel
5 Quantity
of 1
Left Side Panel
6 Quantity
of 1
Right Side Panel
7 Quantity
of 2
Side Shelf Panel
8 Quantity
of 2
Left Leg
9 Quantity
of 2
Right Leg
10 Quantity
of 1
Adjustable Foot
11 Quantity
of 1
Wood Holder
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Periodically apply furniture wax to renew
the finish. Avoid rubbing or scratching the
surface with rough or abrasive objects.
Call customer service at 1-800-633-5096
for assistance, questions, or Parts.
Assembly Tool Required
No.2 Phillips Screwdriver (Not Included)
Stockton Media Fireplace
Assembly Instructions
Figure 1
Insert 4pcs cam locks (C) into holes
on side panels (5) and (6).
Screw 4pcs cam bolts (A) into holes
on middle shelf panel (3).
Attach side panels (5) and (6) to
middle shelf panel (3) by inserting
wood dowels (B) and cam bolts (A)
into corresponding holes until middle
shelf panel (3) and side panels (5)
and (6) meet.
Tighten by rotating cam locks (C)
clockwise with Phillips screwdriver.
Figure 2
Insert 4pcs cam locks (C) into holes
on side panels (5) and (6).
Screw 4pcs cam bolts (A) into holes
on bottom panel (4).
Attach bottom panel (4) to side
panels (5) and (6) by inserting wood
dowels (B) and cam bolts (A) into
corresponding holes until bottom
panel (4) and side panels (5) and (6)
meet.
Tighten by rotating cam locks (C)
clockwise with Phillips screwdriver.
3
C
C
B
A
B
B
A
B
A
C
C
Stockton Media Fireplace
Assembly Instructions
Figure 3
Insert 4 pcs cam locks (C) into holes
on side shelf panels (7).
Screw 4pcs cam bolts (A) into holes
on assembled unit.
Attach side shelf panels (7) to
assembled unit by inserting wood
dowels (B) and cam bolts (A) into
corresponding holes until side shelf
panels (7) and assembled unit meet .
Tighten by rotating cam locks (C)
clockwise with Phillips screwdriver.
Figure 4
Screw bolts (D) clockwise into the
holes on left legs (8) and right legs (9)
as shown.
8
9
6
5
4
7
7
Stockton Media Fireplace
Assembly Instructions
Figure 5
Attach legs (8) and (9) to assembled
unit by inserting the bolts on the legs
into corresponding holes on the
corner of middle shelf panel (3), side
panels (7), and bottom panel (4).
Use half nuts (E) and hex nuts (F) to
connect the bolts (D) on legs.
Tighten hex nuts with wrench (G).
Screw adjustable foot (10) into
the underside of the unit and
tighten by hand.
Figure 6
Insert 4 pcs cam locks (C) into holes
on middle side panels (2).
Screw 4pcs cam bolts (A) into holes
on assembled unit.
Attach middle side panels (2) to
assembled unit by inserting wood
dowels (B) and cam bolts (A) into
corresponding holes until middle side
panels (2) and assembled unit meet.
Tighten by rotating cam locks (C)
clockwise with Phillips screwdriver.
4
10
C
C
A
2
B
B
C
3
Stockton Media Fireplace
Assembly Instructions
Figure 7
Insert 4 pcs cam locks (C) into holes
on assembled unit.
Screw 4pcs cam bolts (A) into holes
on top panel (1).
Attach top panel (1) to assembled
unit by inserting wood dowels (B) and
cam bolts (A) into corresponding
holes until top panel (1) and
assembled unit meet.
Tighten by rotating cam locks (C)
clockwise with Phillips screwdriver.
Figure 8
Place firebox (H) into the
back of the unit as shown.
H
1
2
2
9
9
C
A
B
B
A
B
A
B
C
Stockton Media Fireplace
Assembly Instructions
Figure 9
Use screws (I) to connect
wood holder (11) to bottom
panel.
Tighten screws (I) with
Phillips screwdriver.
Figure 10
Use short screws to connect
brackets to the underside of the
top panel (1) as shown. Tighten
screws with phillips screwdriver.
Drill 1/4 inch pilot holes in near
proximity of the brackets attached to
the top panel. Tap the plastic anchors
into wall.
Use long screws to connect brackets
to plastic anchors on wall.Tighten
screws with phillips screwdriver.
Move this item close to the fastened
wall brackets and tie in both brackets
with plastic straps as shown in
diagram.
Now your Stockton media fireplace is
ready to use.
Warning: Anti-tipping hardware
must be used for this product to
avoid tipping and injury.
11
Please immediately examine this product carefully. Any request for missing parts or damage replacement must be
received within 90 days of your receipt of the product. Replacement, if available, will be honored within this time
frame. Parts will not be available for items arriving fully assembled. We do not recommend modifying product(s)
and we are not responsible for any damages due to product modification(s).
If damages or missing parts are not
reported within 90 days of your receipt, we are under no obligation to provide parts or replacement merchandise.
Please contact Southern Enterprises at 800-633-5096 or in Dallas 972-869-0111/ 9am – 4pm Mon-Fri Central
time if you have product issues or email us at service@seidal.com. Please ask for customer service
representative for issues involving damages or replacement parts. Please ask for technical assistance
representative for any issues with product and assembly/construction.
Please contact the retailer that you purchased from for returns.
Customer Information
Name
Address
City/State/Zip Code
Phone Number
Please indicate where you purchased this item: Store/Website/Catalog
Please indicate color/size/style number:
Style No Parts Letter Parts Description Quantity Needed
Parts Replacement Form
Customer Service 1-800-633-5096
Southern Enterprises, Inc.
600 Freeport Parkway, Suite 200
Coppell, Texas 75019
CAUTION
The top shelf is intended for a flat screen television with a maximum overall width of 50”
and supports up to 175 lb.
VCR shelf should not be loaded with more than 15 lb.
Each side shelf should not be loaded with more than 10 lb.
DO NOT EXCEED RECOMMENDED LOAD. Use with products heavier than the
maximum sizes and weights indicated may result in instability causing possible injury.
This unit contains a permanent warning sticker located on back panel.
Model: FA902900TX
Stockton Media Fireplace
Southern Enterprises, Inc
600 Freeport Parkway, Suite 200
Coppell, Texas, 75019
/
