Extreme Tools RX722501HCBL Operating instructions

Brand: Extreme Tools

Model: RX722501HCBL

Type: Operating instructions

This manual is also suitable for

Model: RX722501HC

Extreme Tools, Inc.

740 Frontenac Rd

Naperville, Illinois 60563

630.369.9303

www.ExtremeTools.net

RX722501HC

Parts List

72 inch Steel Top Hutch

shown on RX722519RC

Step 1: Attach Slide Splicer Posts to Side Panels

a. Slide Splicer Post Assembly (#9) into bottom opening of the

left-hand Side Panel Assembly(#2).

b. Line up hole in Splicer Post with hole in Side Panel.

c. Insert M4-10mm TORX Screw (#10)

and tighten.

d. Repeat for the right-hand

side.

SPACER

NOTE: If the hutch

is going to be used

over the stainless

steel surface, then

remove the spacer

on the bottom of the

side panel.

Step 2: Install Side Panels on Roller Cabinet

a. Remove plastic end caps from the top of the trim located at the

front corners of the roller cabinet.

b. Slide end of splicer channel into opening where plastic end

cap was located until side panel rests on top of MDF/Stainless

Steel Top.

c. Repeat process for right-hand side.

Plastic

End

Cap

Plastic End Cap

Step 3: Secure Side Panels

a. Install one Hold-Down Bracket (#14) on each side

using one at washer (#16) and one M8 bolt (#15)

for each side.

b. If attaching the side locker or side box, do not use

Hold-Down Bracket on that side.

Hold-Down

Bracket

Flat

Washer

M8 Bolt

Step 4: Install Back Panel

a. Pull MDF board/Stainless Steel Top forward approximately 1/8”

from Back Raised Edge (aka: Fence Rail.)

b. Lift Back Panel into place behind the two side panels. Slide the

bottom edge of the Back Panel between the MDF/Stainless

Steel Top and rear fence rail of roller cabinet. Flange on left and

right sides of back panel should be resting against the inside

back edges of both side panels.

c. Use (6) M5 screws (#11) on each side to fasten the back panel to

side panel assemblies.

Back panel ange should

rest inside the Side

Panel

Slide Back Panel down

behind Side Panels with

bottom of Back Panel tting

between roller cabinet fence

rail and top work surface.

Back Raised Edge

(aka: Fence Rail)

Back Raised Edge

(aka: Fence Rail)

Step 5: Secure Back Panel & Set Shelf Height

a. Line up the holes on the left-hand Back Panel Flange with the

threaded inserts of the Side Panel.

b. Secure using (6) screws (#11.)

c. Repeat on for right-hand side panel.

d. Determine the desired height for the Adjustable Shelf. Pre-

thread (2) screws (#11) about halfway in on left-hand and

right-hand sides.

Secure side panel to back panel using (6)

M5x16mm Pan Head Screws

Determine adjustable shelf

height. Pre-thread (2) screws

about halfway in on each side

at desired height.

Step 6: Install Adjustable Shelf

a. Locate the (2) open slots on each side of the shelf. Line up the

open slots with the (4) threaded screws that were installed in

Step 5d. Lay down shelf so that (4) open slots t on top of the

(4) screws.

b. Tighten (4) screws.

c. Locate (2) threaded inserts on the back of the shelf. From

the back of the Back Panel, insert (2) screws through the

pegboard and through the threaded inserts and tighten.

Locate threaded inserts

and insert (2) screws

through the pegboard

and insert holes to

secure shelf to Back

Panel.

Step 7: Attach Gas Struts to Lid

a. Lay the lid down on packaging material so that the front of the lid

is face down. Be sure to use packaging material under the lid so

that it does not get scratched or damaged.

b. Locate the (2) openings near the Top Panel Stiffener.

c. Hold each gas strut so that the larger cylinder end is up and

the smaller piston end is down. Insert the male portion at the

cylinder end of the gas strut into the opening near the top lid

stiffener. Tighten to secure in place.

d. Repeat step c for the other side.

Top of the lid

Opening to

insert male

portion of

gas strut

Opening to insert

male portion of

gas strut

Front Panel of lid

Step 8: Install the Lid onto the body of the Hutch

LID is HEAVY!

LID INSTALLATION REQUIRES ASSISTANCE to LIFT

and MAY REQUIRE the USE of MECHANICAL EQUIPMENT to

PROPERLY POSITION!

a. Lift the lid into place on top of the hutch body as shown below.

Step 8: Secure Lid to Body of Hutch

a. Use the Allen wrench (supplied with the parts) to drive the pre-

threaded M5-16mm Sock Head Screw (#4) into the round

opening on the side of the lid.

b. Insert one plastic hole plug (#5) in each of the socket head

screw openings.

Top of Lid

Side of Hutch

M5-16mm Socket

Head Screw

Drive screw into

opening on side

of lid using Allen

wrench

Step 9: Secure Gas Strut to Side of Hutch

a. Prop open the lid so that it cannot fall.

b. Install the male tting on the piston end of the gas strut into

the opening near the inside top of the side panel.

c. Repeat for the gas strut on the other side.

Secure the male

end of the piston

into the opening

on the side of the

hutch

Step 11: Install Rubber Grommets

a. Insert the Rubber Grommets (#8) in the openings toward the

lower right and left sides of the Back Panel. These openings

are where power cords will exit the Back Panel and plug into a

wall outlet.

Step 10: Install Power Strip with USB Ports (#7)

a. Line up 4 holes on the Power Strip (#7) with 4 holes located

toward the right on the face of the shelf front.

b. Use Phillips screwdriver, (4) M4x10mm Machine Screws (#21)

and (4) M4 LockNuts (#20) to secure power strip.

FULLY ASSEMBLED

EXTREME TOOLS RX SERIES HUTCH

shown on

RX SERIES ROLLER CABINET

Extreme Tools RX722501HCBL Operating instructions

Brand: Extreme Tools

Model: RX722501HCBL

Type: Operating instructions

This manual is also suitable for

Download PDF

report

Extreme Tools RX722501HCBL Operating instructions

This manual is also suitable for

Extreme Tools RX722501HCBL Operating instructions

Related papers

Other documents