Valco baby Car Seat Adapter Operating instructions
- Category
- Strollers
- Type
- Operating instructions
Thank you for purchasing a quality VALCO product. Please read and follow the instructions outlined in this
guide carefully. Familiarise yourself with the construction and safety features; be sure that you understand all
the warnings and safety guidelines before use.
Retain this guide in a safe place for future reference.
PRODUCT REFERENCE GUIDE
GRACO/PEG PEREGO/BRITAX CAR SEAT ADAPTOR
© Copyright VE 2007
Due to our policy of continuous product
development, this product is constantly
evolving. It is possible that some features
or procedures outlined here have changed
since this document was written. If you are
unsure of any procedure shown here, please
contact us via email at info@valcobaby.com
or Canada customers can email canada@
valcobaby.com to obtain the most up to date
information before use. Include the batch
number, which can be found on a sticker on
the frame.
All pictures and diagrams herein are provided
for illustration purposes only. Actual product,
color or fabric may vary. VALCO reserves the
right to modify or alter any specication or
color without notice or obligation to modify
any product previously purchased
FURTHER INFORMATION
In North America only
www.valcobaby.com
1800 610 7850
In Canada only
416 488 1900
FOR USE WITH GRACO
SINGLE/TWIN
CAR SEAT ADAPTOR:
If you haven’t already done so, remove
the front bar or plugs from the nylon
housings on either side of the stroller
frame by pressing each inner ‘release
button’ and lifting the front bar or plug
from the housing.
Insert the car seat adaptor connecting
pieces into the nylon housings.
Be sure that the bar release button is
securely in the housing.
Located on the car seat adaptor
support frame are two sets of tether
straps. The rst set (as shown in Figure
C) rest on the foot rest of the stroller.
Adjust these straps so they wrap
underneath the foot rest of the stroller.
Secure by inserting the male clip into
the female end.
Ensure these straps are as tight as
possible.
To secure the Twin Adaptor see Page 3
‘Secure the Twin Adaptor’.
A
C
B
The following instructions are for the Valco Baby
TriMode Models:
A
B
C
Insert the Adaptor
Secure the Adaptor
Remove Bumper Bar or Housing
Bumper Bar
Nylon Plug
press
1
Position the Car Seat so that the infant
is facing the handlebar of the stroller.
Line up the Car Seat to the Adaptor
frame ensuring that the Car Seat latch
(red lever on back of car seat) rests
under the Adaptor frame.
Once the car seat is in position, take
the second set of tether straps and
place them through the sides of the car
seat, (where a seat belt would go) and
connect via the buckle.
Ensure that the strap is tight and
securely fastened by pulling on the free
end of the strap.
TO REMOVE THE CAR SEAT:
Detach the straps (reversing the process
outlined in E) and lift up the RED LEVER
located on the back of the car seat.
TO REMOVE THE ADAPTOR:
Detach the straps secured beneath the
footrest.
Locate the two nylon release buttons
that sits below the frame at each side of
the stroller.
Press the release button and lift the
adaptor bar out of the nylon housings.
E
D
D
E
F
Insert the Car Seat
Remove Adaptor
F
Secure the Car Seat
2
TO SECURE TWIN CAR SEAT
ADAPTOR:
replace step c in single
adaptor instructions with the
following two steps c-1 and
c-2:
Located on the Car Ceat Adaptor
support frame are two sets of tether
straps. The rst set (as shown in Figure
C-1- 1 )rest on the foot rest of the
stroller.
To secure these straps;
Lift up the footrest ap (Figure C-1- 2 )
and insert the Male clip through the slit
in the stroller frame directly above the
footrest (Figure C-1- 3 ).
Wrap the Female clip around the
closest side of the stroller, meeting the
Male clip underneath the footrest of the
stroller.
Insert the Male clip into the Female clip,
and secure.
continue to follow the single
graco car seat adaptor
instructions step d to f.
FOR USE WITH PEG PEREGO
SINGLE/TWIN
CAR SEAT ADAPTOR:
If you haven’t already done so, remove
the front bar or black plugs from the
nylon housing at either side of the
stroller frame by pressing each inner
“release button” and pulling the front
bar/plug upward.
A
Remove Bumper Bar or Housing
Bumper Bar
Nylon Plug
press
A
1
2
3
Secure the Twin Adaptor
C 1
C 1
C
2
Secure the Twin Adaptor
4
C
2
3
B
Insert the Adaptor
Insert the Car Seat
C
B
C
Insert the car seat adaptor connecting
pieces into the nylon housings.
Be sure that the bar release button is
securely in the housing.
Position the Car Seat so the infant is
facing the handlebar of the stroller.
There are three bars on the adaptor
frame corresponding to the three slots
in the bottom of the car seat. Line
these up, and push the car seat until it
locks into the frame.
Once the car seat is in position, thread
the tether straps through the sides of
the car seat, (where a seat belt would
go) and connect the buckle.
HINT: You may have to unsnap the
snaps on the side pockets of the car
seat to locate the slots.
Ensure that the strap is tight and
secure by pulling on the free end of the
strap.
D
Secure the Car Seat
D
4
A
B
Insert Car Seat Adaptor
Remove Bumper Bar or Housing
Bumper Bar
Nylon Plug
press
TO REMOVE THE CAR SEAT:
Detach the straps (reversing the
process outlined in D) and lift up the
car seat to unlock it from the frame.
TO REMOVE THE CAR SEAT ADAPTOR:
Locate the two nylon release buttons
that sit below the frame at each side of
the stroller.
Press the release button and lift the
adaptor bar out of the nylon housings
FOR USE WITH BRITAX
SINGLE/TWIN
CAR SEAT ADAPTOR:
If you haven’t already done so, remove
the front bar or plugs from the nylon
housings on either side of the stroller
frame by pressing each inner ‘release
button’ and lifting the front bar or plug
from the housing.
Insert the car seat adaptor connecting
pieces into the nylon housings.
Be sure that the bar release button is
securely in the housing.
TWIN ADAPTOR HINT:
When positioning the adaptor, make
sure that the raised end of the adaptor
bar will be resting in the seat portion of
the stroller when connected.
A
B
E
Remove Adaptor
E
5
C
C
Secure the Car Seat
Remove Adaptor
Position the Car Seat so that infant is
facing the handlebar of the stroller.
Line up the Car Seat to the Adaptor
frame ensuring that the Car Seat latch
has clicked on the Adaptor frame.
Once the car seat is in position, thread
the tether straps through the sides of
the car seat, (where a seat belt would
go) and connect the buckle.
Ensure that the strap is tight and
secure by pulling on the free end of the
strap.
TO REMOVE THE CAR SEAT:
Detach the straps (reversing the
process used in D) and lift up the car
seat to unlock it from the frame.
TO REMOVE THE CAR SEAT ADAPTOR:
Locate the two nylon release buttons
that sit below the frame at each side of
the stroller.
Press the release button and lift the
adaptor bar out of the nylon housings.
D
E
E
Insert Carseat
6
D
warnings
Your child’s safety is your responsibility ………
Check all parts for breakage or fatigue before use. Discontinue immediately •
if any part is found to be damaged or broken.
Do not use this Car Seat Adaptor until you have read and understood all of •
the instructions.
warning:• Please be aware that this instruction manual is strictly for
the Valco Car Seat Adaptor. Please know and understand the Car Seat
manufacturers instructions before use.
This adaptor is compatible for use with Graco/Peg Perego/Britax car seats •
accordingly. DO NOT use with any other brand.
Only use this adaptor with the correct model Valco Trimode Single or Twin •
Trimode Stroller accordingly.
Never leave your child unattended. •
alwaYs• check that the Car Seat Adaptor bar, as well as the Car Seat, are
securely fastened.
alwaYs• ensure that child is clear of all moving parts when adjusting the
stroller.
warning:• Avoid serious injury from falling or sliding out. Make sure
that the child is harnessed into the Car Seat using the manufacturer’s
instructions, at all times.
This product is intended for use with infants whose Weight is: 5 - 30 lbs and •
Height: under 30 inches. Excessive weight may cause a hazardous unstable
condition to exist.
Parcels, accessory items or both that are placed on the unit may cause the •
unit to become unstable.
Do not use accessories not designed for your stroller as they may be •
unsafe.
This product is intended for domestic use only. It is not intended for •
commercial use.
North America
www.valcobaby.com
In USA only
1 800 610 7850
In Canada only
416-488-1900
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Valco baby Car Seat Adapter Operating instructions
- Category
- Strollers
- Type
- Operating instructions
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Valco baby Maxi Cosi Car Seat Adaptor Operating instructions
-
-
-
-
-
-
-
-
-
Other documents
-
Joovy Peg Perego User manual
-
Mountain Buggy urban / terrain car seat clip Operating instructions
-
Zooper BU828EZ User manual
-
Baby Jogger Car Seat User manual
-
Mountain Buggy urban / terrain car seat clip Operating instructions
-
-
-
-
-
Combi CATALYST User manual
