Mountain Buggy urban / terrain car seat clip Operating instructions

Brand: Mountain Buggy

Model: urban / terrain car seat clip

Type: Operating instructions

Mountain Buggy urban / terrain car seat clip gives you the freedom to travel with your little one, making it easy to switch between your car and buggy without disturbing your baby. Compatible with most infant car seats, it quickly and securely attaches to your Mountain Buggy urban or terrain stroller, providing a safe and comfortable ride for your child. The car seat clip is easy to install and remove, allowing you to effortlessly transition between modes of transport.

These instructions are for the Carseat Clip which ts the following

model strollers:

UNIVERSAL CARSEAT CLIP INSTRUCTIONS

IMPORTANT, KEEP FOR FUTURE REFERENCE

ACCis21/2/08gen

Unfasten seat from frame along

side tubes.

Push seat forward, then slide

fabric up seat support wire.

Remove seat support wire

from stroller frame at C and D.

Removing Seat

WARNING

• Do not use this Carseat Clip untilyou have

readandunderstoodtheinstructions!

• Che c k you  have  the c orrec t Carseat

Cli p  for  your  mode l  strol l e r. M o d el

na m e/n umber is on  cloth label se wn

intofabricofCarseatClipandonpackaging.

• Neverleaveyourchildunattended.

• ThisCarseatCliptsmostinfantcarseats.Check

carseatcompatibilitywithAuthorizedDealeror

Distributor.

• Donotuseaccessoriesnotdesignedforyour

strollerastheymaybeunsafe.

• Donotleavebabyincarseat(onoroffstroller)

forlongperiodsoftime.

• TheSunhoodandSeatneedtoberemovedfrom

strollerbeforettingCarseatClip.

• Storeitemsremovedinadrysafeplace.

STAGE1

Pull support wire out of sunhood

joint, while pushing against frame.

Note: This operation is child proof

and therefore requires a degree of

force.

RemovingSunhood

seat

support

wire

sunhood

support

wire

bOTh MOdEls

plastic joint

TERRAIN URbAN

Single - T1204 Single - U1204

bOTh MOdEls

URbAN

TERRAIN

Unfasten strap underneath seat

at point A. Unfasten frame straps

at point B.

Repeat step (1) on other side.

Unfasten the sunhood fabric

from the stroller frame and seat

near the handle bar.

WARNING

• CheckcarseattsintoCarseatClipandbuckle

isrmlyfastened.

• Check Carseat Clip is located correctly onto

strollerframe.Referbacktodiagramstoensure

positioning of fasteners and Snap Locks are

correct.

• DonotuseCarseatClipif your areunableto

secure car seat or Carseat Clip. In this case,

contactstorewherestrollerwaspurchasedor

distributorforyourcountry,formorehelp.

• Always remove CarseatClip before collapsing

Stroller.

RemovingCarSeatfromCarseatClip

1. Unbuckle Carseat Clip buckle.

2. Remove straps from slots on car seat.

3. Lift car seat off Carseat Clip.

RemovingCarseatClipfromFrame

1. Open 2 Snap Locks and take Snap Locks off frame tube.

2. Unfasten 4 fasteners on frame and lift Carseat Clip off stroller

frame.

FittingSnapLockstoFrame

Open the 2 Snap Locks by lifting lever up.

Place Snap Locks onto frame directly above bottom fastener on both

sides of stroller.

Close both Snap Locks down at, making sure you hear the lock

“Click” indicating they are fully locked.

OPENPOSITION

“CLICK”

CLOSEDPOSITION

30mm

bottom

fastener

FittingCarseatCliptoStrollerFrame

FittingFabrictoFrame

Attach fasteners on fabric to fasteners on frame at points A,B,C &

D. Fasteners A+B are rst studs above sunhood joint. Fasteners C+D

are below tube joint.

STAGE2

To t fasteners to frame of stroller, identify the diagram for your model,

and then follow the instructions.

FittingCarSeatontoCarseatClip

Pass wide straps attached to

Carseat Clip around outer side of

frame directly below tube joint on

both sides of stroller.

STAGE3

Buckle wide strap across top of car seat at point Z and tighten rmly

by pulling on free end of strap.

Place car seat in Carseat Clip so that baby faces stroller

handlebar.

tube joint

Identify diagram for your model, and then follow the instructions.

Pass wide straps attached to

Carseat Clip around outer side

of frame directly below sunhood

joint on both sides of stroller.

WARNING

• Ensurebabyiscorrectlyandrmlystrappedinto

carseat,beforeplacingontoCarseatClip(check

carseatmanufacturer’sinstructions).

• WhenttingcarseatontoCarseatClip,ALWAYS

keepasteadyinghandoncarseatandbaby,until

CarseatClipstrapissecurelyfastened.

• Be aware of danger time between placement

ofcar seat onto CarseatClip andpoint when

CarseatClipstrapissecured.

• Itisrecommendedthatyoupractisethefollowing

instructionswithoutbabyincarseat.

wide strap

Pass wide strap upwards and through slots provided on each side of

cars seat. (The slots are the same openings as used for car seat belt).

Ensure fabric passes over and around frame tubes.

sunhood

joint

tube

joint

sunhood joint

tube joint

Snap

Lock Lever

Snap

Lock

TERRAIN URbAN

sunhood joint

Mountain Buggy urban / terrain car seat clip Operating instructions

Brand: Mountain Buggy

Model: urban / terrain car seat clip

Type: Operating instructions

Download PDF

report

Mountain Buggy urban / terrain car seat clip Operating instructions

Mountain Buggy urban / terrain car seat clip Operating instructions

Related papers

Other documents