Valco baby Car Seat Adapter Operating instructions

Brand: Valco baby

Model: Car Seat Adapter

Type: Operating instructions

Thank you for purchasing a quality VALCO product. Please read and follow the instructions outlined in this

guide carefully. Familiarise yourself with the construction and safety features; be sure that you understand all

the warnings and safety guidelines before use. This product is for use with the VALCO Latitude stroller in North

American only. This product is not intended for use in Australia.

Important: Please read the following instructions carefully before assembling this product. Retain this

guide in a safe place for future reference.

PRODUCT REFERENCE GUIDE

Due to our policy of continuous

product development, this

product is constantly evolving. It

is possible that some features or

procedures outlined here have

changed since this document

was written. If you are unsure

of any procedure shown here,

please contact us via the web at

info@valcobaby.com to obtain

the most up to date information

before use. Include the batch

number, which can be found on a

sticker on the frame.

All pictures and diagrams herein

are provided for illustration

purposes only. Actual product,

color or fabric may vary. VALCO

reserves the right to modify or

alter any specication or color

without notice or obligation to

modify any product previously

purchased

FURTHER INFORMATION

North America only

www.valcobaby.com

1800 610 7850

Twin Latitude Car

Seat Adapter

Compatible with most Peg Perego Car Seats

INSTALLING YOUR PEG PEREGO

CAR SEAT ADAPTOR

FIGURE A

1. Begin preparing the Latitude stroller for the Car

Seat Adaptor by removing the canopy (hoods) from the

stroller and reclining the seats to their fully reclined

position (detailed instructions in the Twin Latitude

Stroller Instruction Manual).

2. Remove the bumper bar, (detailed instructions in the

Twin Latitude Stroller Instruction Manual).

3. Remove the extra hood and Peg Perego Adaptor

Bar from the packaging and dispose of packaging

responsibly.

FIGURE B

4. Prepare the Hood for installation by rotating the

hood rods so they are aligned with the corresponding

connector pieces on the stroller frame (where the twin

hood was connected.) (1)

NOTE: ENSURE THAT THE HOOD IS PLACED OVER THE

LEFT SEAT OF THE STROLLER (WHEN FACING YOU).

5. Simultaneously slide the hood rods onto the

corresponding raised pieces on the stroller frame and

lock into place. (2)

Figure C

6. Align the Adaptor Bar connector piece with the

corresponding raised piece on the outer frame of the

stroller.

NOTE: BE SURE THAT THE ADAPTOR BAR IS IN ITS

UPRIGHT POSITION BY PULLING THE SUPPORT BAR

AWAY FROM THE ADAPTOR FRAME.

7. Slide the Adaptor onto the corresponding raised piece

and lock into place.

NOTE: ONLY ONE SIDE OF THE ADAPTOR WILL SLIDE

ONTO THE STROLLER FRAME. THE ADAPTOR WILL NOT

BE CONNECTED TO THE MIDDLE FRAME.

Figure D

8. Locate the middle hood connector piece.

9. Unscrew the screw, washer and nut from the middle

piece.

Hood

Seat Reclined

Adaptor Bar

Front View

NOTE: THE UNSCREWING AND SCREWING IS ONLY

PART OF THE INITIAL INSTALLATION PROCESS, AND

WILL NOT HAVE TO BE REPEATED WITH EACH USE.

FIGURE E

10. Insert the remaining unattached adaptor bar into

the centre of the middle connector piece.

FIGURE F

11. Align the adaptor piece with the middle connector

piece and hood piece.

12. Insert the screw, and secure with the washer and

nut.

13. The Adaptor is now secured to the frame with the

support bar resting on the edge of the seat, above the

footrest.

FIGURE G

14. Adjust the footrest upwards.

To do so: Press the adjust button, and move the footrest

to the desired position. (3)

15. Located on the car seat adaptor are two sets of

tether straps. The rst set (as shown in Figure G) rest on

the foot rest of the stroller. Adjust these straps so they

wrap underneath the foot rest of the stroller. (4)

16. Secure by inserting the male clip into the female

end. Ensure these straps are as tight as possible.

17. The adaptor is now securely attached to your stroller.

You may readjust the footrest to suit your child.

FIGURE H

18. Position the Car Seat so the infant is facing the

handlebar of the stroller.

19. Line the Car Seat up with the adaptor bar so that

the Car Seat rests on the adaptor bar when inserted.

Front View

Press

IMPORTANT WARNING: ALWAYS TEST THAT ALL

STRAPS ARE SECURELY ENGAGED BEFORE

USE.

WARNINGS

•Always follow car seat manufacturer’s instructions when using the car seat.

•Be sure to check that all straps are securely xed and in place before use.

• Check all parts for breakage or fatigue before use. Discontinue immediately if any part

is found to be damaged or broken.

• NEVER leave any child unattended at any time.

• This product is intended for use in North America only. It is not intended for use in

Australia.

• This product is intended for domestic use only. It is not intended for commercial use.

In North America only

www.valcobaby.com

1 800 610 7850

FIGURE I

20. Once your car seat is inserted, locate the remaining

set of straps.

21. Take the Male/Female strap and slip the strap

through the car seat belt hook on the side of the car

seat.

22. Repeat with the other strap.

23. Insert Male clip into its Female counterpart and

buckle.

24. Adjust straps to tighten around car seat.

25. You may want to readjust the recline of the seat

to ensure the car seat has the most comfortable and

secure ride.

TO REMOVE YOUR CAR SEAT:

26. Reverse the steps outlined in Figure I and lift out the

car seat.

TO REMOVE YOUR ADAPTOR:

27. Slide all three connector pieces from the stroller,

undo the buckle under the footrest and remove adaptor.

NOTE: THERE IS NO NEED TO UNSCREW THE ADAPTOR.

RETAIN THE ADAPTOR IN THIS FORM FOR EASY FUTURE

INSTALLATIONS.

Valco baby Car Seat Adapter Operating instructions

Valco baby Car Seat Adapter Operating instructions

Valco baby Car Seat Adapter Operating instructions

Related papers

Other documents