Mountain Buggy urban / terrain car seat clip Operating instructions

Brand
Mountain Buggy
Model
urban / terrain car seat clip
Category
Strollers
Type
Operating instructions
IMPORTANT - KEEP FOR FUTURE REFERENCE
SCCGis21/2/08gen
WARNING
• DonotusethisCarseatClipuntilyouhave
readandunderstoodtheinstructions!
• Incorrectusecanmeanseriousinjuryor
deathtoaninfant!
• Donotuseaccessoriesnotdesignedfor
yourstrollerastheymaybeunsafe.
• Neverleaveyourchildunattended.
• CheckyouhavethecorrectCarseatClip
foryourcarseat.
• CheckthatcarseatandCarseatClipare
secureandcannotmoveforward,back,
sidewaysorupwards.
• Makesureinfantisharnessedintothecar
seatusingthecarseatmanufacturer’s
instructions.
• Donotleavebabyincarseat(onoroff
stroller)forlongperiodsoftime.
Pull support wire out of
sunhood joint A. This
operation is child proof
and therefore requires a
degree of force. To assist
in pulling support wire out,
push against stroller frame
with other hand B.
1
1.TemporarilyRemoveSunhood
Repeat step (1) on other
side.
2
Unfasten two middle
fasteners on both sides
of stroller (at B & C) and
peel fabric back, exposing
frame.
1
2
3
2.PartialSeatUnfastening
Single - T1204
Single - U1204
These instructions are for the Carseat Clip which t the
following model strollers:
Graco
®
model:SnugRide
®
SINGLE carSEat cLIp INStructIoNS -
A
B
Sunhood Joint
URBAN
TERRAIN
STAGEONE
ALL MODELS
A
ALL MODELS
Loosen the strap beneath
seat at point A.
URBAN
Recline seat slightly.
B
C
Sunhood
Joint
The stroller seat does not need to be removed to t Carseat Clip.
The sunhood wires need to be removed from sunhood joints to allow
Carseat Clip to be tted. These wires are re-attached to stroller once
Carseat Clip has been tted.
FittingCarseatCliptoFrame
STAGETWO
FittingCarSeatontoCarseatClip
STAGETHREE
OPENPOSITION CLOSEDPOSITION
WARNING
• Makesureinfantisharnessedintothecarseatusing
thecarseatmanufacturer’sinstructions.
• WhenttingcarseatontoCarseatClip,ALWAYS
KEEP A STEADYING HAND ON CAR SEAT
ANDINFANT,untilCarseatClipstrapissecurely
fastened.
• CheckcarseattsintoCarseatClipandbuckleis
rmlyfastened.
• CheckCarseatClipislocatedcorrectlyontostroller
frame.Referbacktodiagramstoensurepositioning
ofsnaplocksarecorrect.
• CheckcarseatandCarseatCliparesecureand
cannotmoveforward,back,sidewaysorupwards.
• DonotuseCarseatClipifyouareunabletosecure
carseatorCarseatClip.Inthiscasecontactstore
wherestrollerwaspurchasedordistributorforyour
country,formorehelp.
• ITISRECOMMENDEDTHAT YOUPRACTICE
THEFOLLOWINGINSTRUCTIONSWITHOUT
INFANTINCARSEAT.
Place car seat in CarseatClip so that
infant is facing the stroller handle bar.
1
Ensure the car seat latch has clicked on
to the CarseatClip bar.
2
Pass wide straps on each side of
Carseat Clip upward and through
slots provided on each side of car seat.
(The slots are the same openings as
used for car seat belt.)
3
Buckle the wide strap across top of car
seat and tighten rmly by pulling on free
end of strap.
4
RemovingCarSeatfromCarseatClip
STAGEFOUR
Carseat Clip Bar
UnbuckleCarseatClip buckle.
1
Remove straps from slots on car seat.
2
Pull up car seat latch handle to release
car seat from Carseat Clip bar.
3
RemovingCarseatClipfromStroller
STAGEFIVE
1
2
Close all Snap Locks down at, making sure you hear the lock “click”-
indicating they are fully locked.
3
PicturedonUrban
Snap Locks
Snap Locks
TheCarseatClipcomesassembledforUrbanmodel.
Open all four Snap Locks by lifting up levers.
Press CarseatClipon to frame so that TOPSnap Locks are directly
above sunhood joints (on both sides).
Allen Key
A
A
B
B
C
C
(i) Using Allen Key supplied, remove Snap Locks at points B (both sides
by rotating screw in an anti-clockwise direction.
(ii) Using Allen Key supplied, place removed Snap Locks at points C (both
sides) by rotating screw in a clockwise direction until screw is tight and
Snap Locks are secure.
Car Seat Latch
Lift car seat off Carseat Clip.
4
Car Seat
Latch
Handle
Before placing Carseat Clip
on stroller frame, the Snap
Locks at points B need to
be removed and placed at
points C (on both sides).
Snap Locks
“CLICK”
TERRAIN & URBAN
TERRAIN ONLY
Sunhood Joint
Sunhood Joint
URBAN TERRAIN
Re-AttachingSunhoodWires
Push sunhood wires back into sunhood joints (refer Stage One)
1
Remove sunhood wires (refer Stage One).
Open all four Snap Locks by lifting up levers.
Lift Carseat Clip off stroller frame.
Re-attach sunhood wires (refer Stage Three).
Re-attach two middle fasteners on both sides of stroller.
Tighten strap beneath seat (refer Stage One).
1
2
3
4
5
URBAN
6
  • Page 1 1
  • Page 2 2

Mountain Buggy urban / terrain car seat clip Operating instructions

Brand
Mountain Buggy
Model
urban / terrain car seat clip
Category
Strollers
Type
Operating instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents