VTech VM3261-2 Quick start guide
- Category
- Babyphones
- Type
- Quick start guide
VTech VM3261-2 is a baby monitor system that allows you to keep an eye on your baby from anywhere in your home. It features a high-resolution color display, a built-in microphone and speaker, and night vision capabilities. You can use it to monitor your baby's sleep, play, or simply to stay connected with them. The system is easy to set up and use, and it comes with a variety of features to make it even more convenient.
Here are some of the key features of the VTech VM3261-2:
- High-resolution color display: The large, high-resolution color display gives you a clear view of your baby, even in low-light conditions.
VTech VM3261-2 is a baby monitor system that allows you to keep an eye on your baby from anywhere in your home. It features a high-resolution color display, a built-in microphone and speaker, and night vision capabilities. You can use it to monitor your baby's sleep, play, or simply to stay connected with them. The system is easy to set up and use, and it comes with a variety of features to make it even more convenient.
Here are some of the key features of the VTech VM3261-2:
- High-resolution color display: The large, high-resolution color display gives you a clear view of your baby, even in low-light conditions.
What’s in the box
Connect and power on - Baby unit Connect and power on - Parent unit
CAUTION
• The default volume of your parent unit is
level 4, and the maximum volume is level 5.
If you experience high-pitched screeching
noise from your baby monitor while
positioning:
- Make sure your baby unit and parent unit
are more than 3 feet (1 meter) apart, OR
- Turn down the volume of your parent unit.
VM3261-2 baby monitor system
Baby’s room Living room
Go to www.vtechphones.com
to register your product for
enhanced warranty support and
latest VTech product news.
VM3261-2
Quick start guide
Install the battery
3ft (1m)
3ft (1m)
THIS SIDE UP
6U]KXOTMUT
6U]KXOTMUT
2s
Strangulation
Hazard
Keep this cord out of reach of children.
The cord needs to be at least three feet
away from the child at all times. Do not
use with an extension cord. Do not
remove this tag.
Éloignez ce cordon des enfants. Le
cordon doit se trouver à au moins trois
pieds d’un enfant et ce, en tout temps.
N’utilisez pas de rallonge. Ne retirez pas
cette étiquette.
Mantenga este cable fuera de la alcance
de los niños. Este cable debe estar por
lo menos tres pies fuera de la alcance
del niño en todo momento. No lo use
con una extensión inalámbrica. No quite
esta etiqueta.
Risque
d’étranglement
Riesgo de
estrangulación
Strangulation
Hazard
Keep this cord out of reach of children.
The cord needs to be at least three feet
away from the child at all times. Do not
use with an extension cord. Do not
remove this tag.
Éloignez ce cordon des enfants. Le
cordon doit se trouver à au moins trois
pieds d’un enfant et ce, en tout temps.
N’utilisez pas de rallonge. Ne retirez pas
cette étiquette.
Mantenga este cable fuera de la alcance
de los niños. Este cable debe estar por
lo menos tres pies fuera de la alcance
del niño en todo momento. No lo use
con una extensión inalámbrica. No quite
esta etiqueta.
Risque
d’étranglement
Riesgo de
estrangulación
> 3ft (1m)
Positioning - Baby unit
Once you power on both your baby unit and parent unit, your parent unit displays
image from the baby unit, and the LINK LED light turns on. The POWER LED light of
the baby unit also turns on.
5
Status check
TALK
Overview - Parent unit
Stand
On/off
Zoom
LED lights
/ LCD ON/OFF
MENU/SELECT
Power jack
Speaker
VOL
-
VOL
+
Overview - Baby unit
Camera
Microphone
Temperature sensor
Infrared LEDs
Speaker
1
4
8
9
11
10
12
2
3
5
6
7
1
4
8
9
11
10
12
2
3
5
6
7
ON/OFF switch
ON/OFF LED light
PAIR
Antenna
Power Jack
Threaded socket
If you are viewing baby unit , the POWER LED light of baby unit turns on. As
baby unit is not being viewed, its POWER LED light flashes.
LCD display
Battery
compartment
cover
Microphone
Arrow keys
Light sensor
Specifications are subject to change without notice.
© 2018 VTech Communications, Inc. All rights reserved.
01/18. VM3261-2_QSG_V1.
Document order number: 96-012000-010-100
Basic operation - Parent unit
Adjust speaker volume
Press VOL - or VOL +
to adjust your parent unit
speaker volume. It determines the volume of sound
transmitted from your baby units.
Zoom
Press to zoom in or out.
Talk to your baby unit
Press and hold TALK and speak to your parent unit.
Your voice is transmitted to the baby unit.
Turn off the screen
Press and hold LCD ON/OFF to switch off the screen.
You can still hear sound from the selected baby unit.
Turn off the parent unit
Press and hold to power off your parent unit.
Basic operation - Baby unit
Night vision
The baby unit has infrared LEDs that allow you to
see your baby at night or in a dark room. When
the baby unit detects low light levels, the infrared
LEDs turn on automatically. The images from the
baby unit are in black and white, and appears
on screen.
NOTES
• I t is norma l if you see a sh ort whi te glare o n your
parent un it screen as the bab y unit is adapting to t he
dark environment.
• W hen the infrared L EDs are on, t he image s are in
black an d white. T his is nor mal.
TIP
• Depending on the surroundings and other
interfering factors, like lightings, objects, colors and
backgrounds, the display resolution may vary. Adjust
the baby unit’s angle, or place the baby unit at a
higher level to prevent glare and blurry display.
Turn off the baby unit
Slide the ON/OFF switch to OFF to power off
your baby unit.
Press to switch to another camera in SINGLE-CAM mode.
Change different views - Single-cam
Change different views - Patrol
In PATROL mode:
1. Press MENU when the parent unit is idle.
2. Press or to choose , then press .
3. Press or to switch on or off PATROL mode, then press SELECT to confirm your selection.
Sound activation
When the baby unit being viewed detects no sound, the
parent unit screen stays off to save power. Once a sound is
detected, the parent unit screen turns on automatically. It will
then turn off again after 50 seconds of no sound detection.
Press .
10s
Use the menu
Press MENU to enter the main menu, or save a setting.
You can use the parent unit for advanced settings or
operations, such as to play or stop the baby unit lullaby,
or to adjust the baby unit sound sensitivity.
While in the main menu:
• Press or to scroll among the menu options.
• Press to enter the desired submenu.
• Press MENU to exit the main menu.
While in the submenu:
• Press or to scroll among the submenu options.
• Press to enter the desired 2nd level submenu.
• Press SELECT to confirm your selec tion.
• Press to exit the submenu.
If you drill the holes into a stud,
go to step 3.
-OR-
If you drill the holes into an
object other than a stud, insert
the wall anchors into the holes.
Tap gently on the ends with a
hammer until the wall anchors
are flush with the wall.
Mount the baby unit (optional)
You can maximize your baby unit’s viewing angles by
tilting the wall mount bracket.
Hold the baby unit, and then rotate the knob in
anticlockwise direction. This will loosen the joint of the wall
mount bracket.
Tilt your baby unit up or down to adjust to your preferred
angle.
Then, rotate the knob in clockwise direction to tighten the
joint and secure the angle.
6U]KXOTMULL
6U]KXOTMULL
TIP
• Press any keys on the parent unit to turn on the screen again.
Long press
2s
Place the wall mount bracket on a
wall and then use a pencil to mark
the top and the bottom holes as
shown. Remove the wall mount
bracket and drill two holes in the wall
(7/32 inch drill bit).
NOTES
• Check for reception strength and
camera angle before drilling the holes.
Align the wall mount bracket and
screws with the holes in the wall
as shown. Tighten the screw in the
middle hole first, so that the wall
mount bracket position is fixed.
You can tighten the other screw in
the top hole.
Place the baby unit on the wall
mount bracket. Tighten the screw into
the threaded socket at the bottom to
secure the baby unit.
OR
Insert the screws into the holes
and tighten the screws until
only 1/4 inch of the screws are
exposed.
Place the baby unit on the wall mount bracket. Tighten
the screw into the threaded socket at the bottom to
secure the baby unit. Align the holes on the wall mount
bracket with the screws on the wall, and slide the wall
mount bracket down until it locks into place.
Submenu
Mainmenu
Press and hold
63
> More than 1
meter (3 feet)
63
-
1
-
2
VTech VM3261-2 Quick start guide
- Category
- Babyphones
- Type
- Quick start guide
VTech VM3261-2 is a baby monitor system that allows you to keep an eye on your baby from anywhere in your home. It features a high-resolution color display, a built-in microphone and speaker, and night vision capabilities. You can use it to monitor your baby's sleep, play, or simply to stay connected with them. The system is easy to set up and use, and it comes with a variety of features to make it even more convenient.
Here are some of the key features of the VTech VM3261-2:
- High-resolution color display: The large, high-resolution color display gives you a clear view of your baby, even in low-light conditions.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
VTech VM5271 Quick start guide
-
-
-
VTech VM3254 Video Baby Monitor User guide
-
-
-
VTech VM4261-2 Quick start guide
-
-
-