AXIOMTEK icon-101CU Quick Installation Manual

Brand: AXIOMTEK

Model: icon-101CU

Type: Quick Installation Manual

iCON-101CU Quick Installation Guide

Version A1 Oct 2011

Printed in Taiwan

9413C101000E

I. Overview

The CAN (Controller Area Network) is a serial bus system and is

usually used in structuring intelligent industrial device networks and

building smart automatic control systems. The iCON-101CU is a

cost-efficient industrial converter for pairs to PC using the standard

USB interface. It supports CAN monitor tool that displays the CAN

received message in decimal or hexadecimal mode. This converter

shows the time stamp of each received message. The GUI

management program and programming guide both are ready for

use. The CAN host, monitor or HMI can access and control CAN

device through iCON-101CU.

There is a User’s Manual CD-ROM for the iCON-101CU

system. Please consult your local vendor for assistance if

you have any difficulties in installing.

iCON-101CU Quick Installation Guide

Version A1 Oct 2011

Printed in Taiwan

9413C101000E

II. Features

 Full compliance with USB 1.1/2.0 (fully speed)

 Full compliance with CAN 2.0A and CAN 2.0B

 D-sub DB9 CAN port support 3KV isolation

 Easily setup to CAN terminator by software configuring

 CAN transmission speed up to 1Mbps

 Powered by the USB bus

 USB type B connector Complies with Class 1, DIV II minimum

withdrawal requirement of 15N

 Provides DIN-Rail mounting, Status LED indicators

 Driver supports Windows® Server 2008; 2003/Vista/2000/XP/7

and Linux OS

 -40~70℃ wide temperature operating Suitable for industrial

automation and power automation field applications

III. USB connector

IV. CAN interface connector

Pin Signal Pin Signal

1 5V 2 D-

3 D+ 4 GND

Pin Signal Function

1 NC No connect

2 CAN_L CAN data line (Low)

3 ISOGND Ground

4 NC No connect

5 NC No connect

6 ISOGND Ground

7 CAN_H CAN data line (High)

8 NC No connect

9 5V (option) 5V (Option)

All Components are fragile and sensitive. If you need to replace or return any components for repair, you must

contact authorized technicians for a professional handling.

iCON-101CU Quick Installation Guide

Version A1 Oct 2011

Printed in Taiwan

9413C101000E

V. LED indicator

VI. Driver

It is necessary to install driver so the iCON-101CU can work properly

under operating system. About how to install the device driver under

Windows XP. You can follow the user manual instructions to install

the driver.

VII. Commands

To meet user’s application purpose, commands are provided for

CAN module management, transmitting and receiving messages

through iCON-101CU. Each command consists of 3 parts: StartByte,

ContentOfCommand and StopByte.

StartByte ContentofCommand StopByte

@ CMD 0x0d (carriage return)

LED Color Function

Green

(POWER)

Light on

Power status indicator. The

LED light is on when

iCON-101CU is powered on.

Light on

PC is sending data to CAN

network.

Flashing

PC is reading data from

CAN network.

Green

(CAN Act.)

Light off CAN transmission is idle.

Light on

CAN transmission error

occurred.

Orange

(CAN Error)

Light off

CAN transmission is

working properly.

Green

(USB Act.)

Flashing

The LED light flashes during

USB data transmission.

Light on

CAN termination resistor is

enabled.

Orange

(CAN

Termination)

Light off

CAN termination resistor is

disabled.

There is a User’s Manual CD-ROM for the iCON-101CU

system. Please consult your local vendor for assistance if

you have any difficulties in installing. the system.

iCON-101CU Quick Installation Guide

Version A1 Oct 2011

Printed in Taiwan

9413C101000E

Operation can be set to command and data mode. In command

mode, CAN module accepts commands and this is the default mode.

Data mode is the mode that only and automatically report CAN

messages to UART port or USB port based on settings until user

inputs command string ‘+++’.

VIII. Utility

You can use hyperterminal program to send and retrieve command

messages from iCON-101CU. Or Use AXCAN utility to configure

CAN communication parameters. It is also used to transmit or

receive CAN messages for simple function testing. About how to

install AXCAN software utility please follow the user manual

instructions.

All Components are fragile and sensitive. If you need to replace or return any components for repair, you must

contact authorized technicians for a professional handling.

AXIOMTEK icon-101CU Quick Installation Manual

AXIOMTEK icon-101CU Quick Installation Manual

AXIOMTEK icon-101CU Quick Installation Manual

Related papers

Other documents