AXIOMTEK SBC84600 Series Quick Installation Manual

Brand: AXIOMTEK

Model: SBC84600 Series

Type: Quick Installation Manual

SBC84600 Series Quick Installation Guide

Version A7 September 2005

Printed in Taiwan

94284600060E

Checklist



SBC84600 Board x 1



Quick Installation Guide x 1



Product Information CD-ROM x 1



2-pin jumper cap, Pitch=2.54mm x 5



2-pin jumper cap, Pitch=2.0mm x 10



3mm screw nuts x 2



PS/2 Keyboard/Mouse adapter x 1



2.5” & 3.5” HDD cable x 1



Power Cable 8 Pin x 1



COM+Printer extension cables

with bracket, Pitch=2.0mm x 1



COM extension cables with

bracket, Pitch=2.0mm x 1



FPC cable for extra display

features x 2



Audio Cable x 1 (for

SBC84600VEA Series

Products only)

If there are damaged or missing parts, contact your supplier

and/or dealer immediately. Do not attempt to apply power to

the board if there is damage to any of its components.

Note: The Windows XP Pro/home SP2 edition is not

supported by VIA non-Nehemiah core version processors

which are adopted by SBC84600VEA/VE-400 and

SBC84600VEA/VE-800. For more information please

reference

http://support.microsoft.com/kb/893356

II.

Jumper Settings

Before turning on the power to the SBC84600 Series,

please make sure that all jumpers are on their default

settings as listed on the table below.

Jumper Default Setting Jumper Setting

JP1

Watchdog Trigger Mode: Disabled Open

JP2

Flat Panel Power Selection: VDDM at 5V Short 1-2

JP3

Clear CMOS Setting: Norma Short 1-2

JP4

COM2 Port Setting: RS-232 Short 1-2

JP5

COM2 Port Setting: RS-232 Short 3-5, 4-6

JP6

COM2 Port Setting: RS-232 Short 3-5, 4-6

JP7

Power Supply Selection: AT power supply Short 1-2

JP8

COM1 Signal/+5V Selection

Default: COM Signal

Short 2-3

JP9

COM2 Signal/+5V Selection

Default: COM Signal

Short 2-3

Please refer to the Product Information CD for the complete version of the User’s Manual,

drivers, and utilities for the SBC84600 Series CPU Card.

SBC84600 Series Quick Installation Guide

Version A7 September 2005

Printed in Taiwan

94284600060E

JP10

COM4 Signal/+5V Selection

Default: COM Signal

Short 2-3

JP11

COM3 Signal/+5V Selection

Default: COM Signal

Short 2-3

JP12

Compact Flash Voltage Selection

Default: 3.3V

Short 1-2

III.

SBC84600 Connectors

Connectors Label

44 Pin IDE Connector CN1 TV Connector CN14

44-pin LCD Connector CN2 FDD Connector CN15

Flat Panel Bezel Connector CN3 USB connector USB1, USB2

20-pin LCD Connector CN4 VGA CRT Connector VGA1

CPU FAN +5V Connector CN5 Ethernet Connector LAN1

Printer Port Connector CN7 PC/104 Connector J1, J2

Digital I/O Port Connector CN8 COM Connector COM1

ATX Power On/Off Button CN9 COM Connector COM2

Power Input Connectors CN10 COM Connector COM3

IrDA Connector CN11 COM Connector COM4

AC97 Link Interface CN12 Compact Flash Connector CF1

Keyboard and Mouse

Connector

CN13 VIDEO Connector VIDEO1

Temperature sensor

JP17

IV. AX93102

Connector

Connectors Label

CD AUDIO INPUT CN2 AUDIO PHONE JACK CON1

For SBC84600VEA series products only.

The complete version of the User’s Manual, along with the drivers/utilities software

programs are in the Product Information CD of the SBC84600 Series CPU Card.

SBC84600 Series Quick Installation Guide

Version A7 September 2005

Printed in Taiwan

94284600060E

Additional Information

User’s Manual and other documents are in

Acrobat PDF format. The Product Information

CD contains the Adobe Acrobat 3.0 Reader

installation software for user’s convenience.

VI.

Board Layout

The complete version of the User’s Manual, along with the drivers/utilities software

programs are in the Product Information CD of the SBC84600 Series CPU Card.

SBC84600 Series Quick Installation Guide

Version A7 September 2005

Printed in Taiwan

94284600060E

VII Installation Procedures

Please follow the steps below to install the SBC84600 onto a

chassis:

1. Remove the pillar (a) from the SBC84600 as shown in

Figure 1.

2. Screw the pillar (a) removed from the SBC84600 and

another three pillars (c), which have same height with

the pillar (a), to the chassis as shown in the Figure 2.

3. Use the bolt (b) on the SBC84600 module to screw

the module with the pillar (a) on the chassis.

The complete version of the User’s Manual, along with the drivers/utilities software

programs are in the Product Information CD of the SBC84600 Series CPU Card.

(a)

SBC84600 Series Quick Installation Guide

Version A7 September 2005

Printed in Taiwan

94284600060E

4. Screw three proper bolts (d) to the other three pillars

Figure 2.

(c)

(b)

(a)

(d)

The complete version of the User’s Manual, along with the drivers/utilities software

programs are in the Product Information CD of the SBC84600 Series CPU Card.

SBC84600 Series Quick Installation Guide

Version A7 September 2005

Printed in Taiwan

94284600060E

5. If the Audio kit, AX93102, is used, plug the 10-pin

female box-header of the AX93102 onto the 10-pin

male box-header of the SBC84600 as shown on

Figure 3.

6. Make sure the spacer support (e) fit into the hole (f)

on the SBC84600.

(

)

(

)

AX93102

10-pin female

box-header

10-pin male

box-header

The complete version of the User’s Manual, along with the drivers/utilities software

programs are in the Product Information CD of the SBC84600 Series CPU Card.

AXIOMTEK SBC84600 Series Quick Installation Manual

AXIOMTEK SBC84600 Series Quick Installation Manual

AXIOMTEK SBC84600 Series Quick Installation Manual

Related papers

Other documents