IDIS DA-JB4600 Installation guide

Brand
IDIS
Model
DA-JB4600
Category
Security camera accessories
Type
Installation guide

IDIS DA-JB4600 is a junction box designed for use with specific IDIS camera models. It allows for secure and organized mounting of the camera, as well as cable management and protection.

The DA-JB4600 features a durable construction and is intended to be wall-mounted. It includes a bracket for camera attachment, a top cover for cable pass-through and waterproofing, and a camera dome cover for added protection. ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­

IDIS DA-JB4600 is a junction box designed for use with specific IDIS camera models. It allows for secure and organized mounting of the camera, as well as cable management and protection.

The DA-JB4600 features a durable construction and is intended to be wall-mounted. It includes a bracket for camera attachment, a top cover for cable pass-through and waterproofing, and a camera dome cover for added protection. ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­

DA-JB4600 INSTALLATION MANUAL
This manual is intended for users of the DA-JB4600 junction box. It
includes instructions for mounting the DA-JB4600 junction box to a wall.
• This junction box is intended to be used with some models of
cameras. Do not use it with other models of cameras.
• This installation should be performed by a qualied service
personnel in conformance to all local codes.
• You may need to reinforce the wall. If the wall is not strong
enough to support the camera, the camera may fall.
• Do not use this product for other purposes.
Mounting: DC-D4213WRX, DC-D4513WRX
1
Mount the bracket to the wall by using the
screws.
2
Insert cables from external devices, network
and power adapter.
3
Pass the cable through the top cover, insert the
waterproof bushing provided with the product
into the cable and insert it into the top cover
hole as the gure.
• Cable diameters that can be fastened to the bushing
are 4-6mm(0.15"-0.23"), and other sizes require a
separate sealing nish.
• Bushings that do not tighten cables and unused holes
require a separate sealing nish.
4
Fasten the top cover and the body.
5
Connect the cable to the camera and screw the
camera onto the top cover.
If the cable is bent too much when the camera is installed,
a separate sealing nish is required as the waterproof
function may be weakened.
6
Screw the camera dome cover onto the camera
body using the Allen wrench provided with the
product.
7
Turn on power.
Mounting: DC-Y6513WRX, TC-D4222WRX
1
Mount the bracket to the wall by using the
screws.
2
Insert cables from external devices, network
and power adapter.
Camera
Dome
Cover
Bracket
Camera
Body
IDIS Co., Ltd.
For more information, please visit www.idisglobal.com
3
Pass the cable through the top cover and then
fasten the camera to the top cover.
4
Screw the camera top cover onto the camera
body using the Allen wrench provided with the
product.
5
Insert the waterproof bushing provided with
the product into the cable and insert it into the
top cover hole as the gure.
• Cable diameters that can be fastened to the bushing
are 4-6mm(0.15"-0.23"), and other sizes require a
separate sealing nish.
• If the cable is bent excessively when tightening the
bushing, the waterproong function may be weakened.
• Bushings that do not tighten cables and unused holes
require a separate sealing nish.
6
Connect the cables and x the top cover to the
bracket.
7
Turn on power.
Connect your specic model of camera to the bracket as follows:
1 12 2
3
3
3
Screw No.1 (2-point): DC-Y6513WRX using 2 screws
Screw No.2 (2-point): TC-D4222WRX using 2 screws
Screw No.3 (3-point): DC-D4213WRX, DC-D4513WRX using 2 screws
Dimensions
Unit: mm (inch)
60.5 (2.38)
50.5 (1.98)
162 (6.37)
25.5 (1)
90 (3.54)
63.64 (2.5)
63.64 (2.5)
40.31 (1.58)
40.31 (1.58)
Ver.1.0
  • Page 1 1
  • Page 2 2

IDIS DA-JB4600 Installation guide

Brand
IDIS
Model
DA-JB4600
Category
Security camera accessories
Type
Installation guide

IDIS DA-JB4600 is a junction box designed for use with specific IDIS camera models. It allows for secure and organized mounting of the camera, as well as cable management and protection.

The DA-JB4600 features a durable construction and is intended to be wall-mounted. It includes a bracket for camera attachment, a top cover for cable pass-through and waterproofing, and a camera dome cover for added protection. ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents