Shining 3D AccuFab-D1s Installation guide

Brand: Shining 3D

Model: AccuFab-D1s

Type: Installation guide

Shining 3D AccuFab-D1s is a high-precision 3D printer capable of producing objects with a layer thickness of 20-100 microns. It features a large build volume of 192 x 120 x 185 mm, making it suitable for a wide range of applications, including prototyping, manufacturing, and dentistry. The printer is equipped with a dual-tank system, allowing for easy switching between different resins, and a user-friendly touchscreen interface. Additionally, it supports both USB and Ethernet connectivity for flexible file transfer options.

Installation Guide

3D Printer

AccuFab-D1s

n i

m .m in t

Installation Procedure

Unpacking

Remove steel clasps on the wooden case

to open it. Cut the straps and open the

Open the cover, take out accessory box,resin tank x 2, power adaptor and power

cable from ﬁxing foam.

Take out resin tanks and remove the protective ﬁlms.

m & .

Take out the printer and remove PE bag.

Open the chamber door, take out the ﬁx

foa

Take out build platfor he ﬁx foa

Plug in the power adaptor and connect

it with power cable. Press the power

butto n the back, then press the

power butto n the front.

Network Port

Power Button（back）

B Type USB Port

Power Port

STEP 1

Boot Printer

STEP 2

1）

3）4）

2）

inner box.

STEP 4 Add Material

STEP 3 Install the Printer

The build platform bracket will move up automatically after booting the printer. It is time to install the resin tank and the build platform.

Remove the protective ﬁlm on the

protection glass. Inset the resin tank

into the card slot and push it to the

end in the direction indicated in the

ﬁgure. When the edges of the resin

tank are inside at right angles, it

means the resin tank is placed

appropriately.

Install the resin tank

Remove the protective ﬁlm on the

build platform. Open the handle and

insert the build platform into the

bracket in the direction indicated in

the ﬁgure. Close the handle and lock

the platform.

Install the build platform

Note that the resin level should be between the indicator lines

of minimum and maximum.

Note: You can also add resin during printing without pausing.

Please refer to the “AccuFab-D1s Quick Start Guide” in the ﬂash drive. The ﬂash drive can be used for data transmission later on.

First PrintSTEP 5

Shake for 2 mins before pouring material into the resin tank to

avoid sediment.

Product Preview

Part List

Network port Power port

Chamber Door

Resin Tank

Touch Screen

Power Button

（front）

Handle Build Platform Bracket

Build Platform

Z axis

Protection Glass

USB Port

2 x Resin Tank Power Adaptor Power Cable USB

Flash Drive

Build Platform

Ethernet Cable

Scraper ⑤ ⑥

Brush

Quality Certiﬁcation Installation Guide

⑦

Cleaning Box Cloth ⑨

PET Card

③② Angular ④

Knife Putty Knife Disposal Gloves

Build Platform：Due to the test printing in the factory, the surface

may have few scratches, which will not aﬀect regular use.

Flash Drive：

Angular Knife：Used to remove models from the platform after

printing ﬁnished.

Putty Knife：Used to remove models from the platform after

printing ﬁnished.

①Scraper：

Used to stir resin in the tank to avoid sediment.

Brush：Used to clean extra resin on the model.

Cleaning Box：

Used to store parts or alcohol.

Cloth：

Used to clean optical path including projector lens,

protection glass and resin tank glass.

PET Card：Used to level the platform and remove the cured

layer.

⑥

⑤

⑦

⑧

⑨

②

③

④

⑧

①

Flash drive contains Installer of AccuWare, Printer profile

“*.sndev” , User Manual , Quick Start Guide and “Factory test reports”.

B-type USB port Power button (back)

Technical resource:

Document Download Center:

upport Center:

Aftersales service:

Shining 3D AccuFab-D1s Installation guide

Shining 3D AccuFab-D1s Installation guide

Shining 3D AccuFab-D1s Installation guide

Related papers

Other documents