90830-01011

OPT7 90830-01011 Installation guide

  • Hello! I'm a chat assistant and I've reviewed the user guide for the OPT7 Quantum Rock Lights. This document provides instructions for installing and operating the rock lights, detailing features such as RGB and white light control, along with various color and brightness settings. I'm ready to answer any specific questions you have about these lights or their setup.
  • What is the default color when I first turn on the 'RGB' light?
    How many solid color modes are available?
    What is the default color when I turn on the independent white light?
    What is the IP rating for the Rock Light Pods?
QUANTUM ROCK LIGHTS
INSTALL GUIDE
FULL-SIZE REMOTE CONTROL BUTTON LAYOUT
x6
10ft Extension Cable
Fuse Tap (3 dierent sizes) x1
Metal Screw x8
12V Constant Power Wire x1
Qu antum Roc k Light Pod x4 Rubb er Pa d x4
14
Control Box with Accessory Wire x1
Full-Size Remote x1
Control Wire
Control wire MUST be connected
to a 12V accessory (ACC/ON) fuse tap in
order for the rock light work properly.
*See step 8 for more details.
OPT7 Lighting is not liable for damages or personal injuries while installing this product. The Installa-
tion Guide is intended as assistance to reduce setup time. OPT7 Lighting assumes no responsibility for
improper installation. If you are unfamiliar with your vehicle or inexperienced with aftermarket
upgrades, please seek professional assistance.
SPECIFICATIONS
Wattage
Amp Draw
8 LEDs
Brightness
Voltage
Resistance
Operating Temperature
8W Per Pod
Quad-Core CREE
8A
1,600 Lumens Per Pod
10-30V
IP68 Water-Resistant (Pod Only)
-20°-150°F
DISCLAIMER
NEED HELP? 2 YEAR WARRANTY
Scan for troubleshooting tips,
and more.
- Only control “RGB” light (Default color when
you rst turn it on -> “White/Solid” )
- Brightness Setting: 50 Levels
2. Dimmer +/-
- 20 dierent solid modes
(See Table 3 for color denitions)
3. Color Selector
- Default color when you rst turn it on ->
“White/Solid & Brightness 100%”
4.1 ON & OFF
- Brightness Setting: 50 Levels
4.2 Dimmer +/-
- Brightness Setting: 4 Levels
4.3 Default brightness
4. Independent Control Of White Light
1. ON & OFF
- Need to record the last operation mode and
color when you turn it on again
12
3
4
56
INSTALLATION STEPS
Designate your mounting locations for each Rock Light Pod and the
control box. (Refer to page 2 for recommended mounting locations)
Avoid hot surfaces and/or moving parts.
Use a pen to mark the holes where you want to mount the Rock Light
Pods. Then, drill a 5/32” hole(s) for the wire connector to pass through.
Drill a 7/64” hole for each marked hole.
Secure the Rock Light Pods using the included screws. (If mounting on a
rounded or uneven surface, utilize the optional rubber mounting pads.)
Caution: Rock Light Pods become extremely hot during use - keep
away from any vehicle parts that may be damaged by exposure to
high temperatures.
Connect all Rock Light Pod lines to the control box connectors. Secure
by twisting.
Connect the red positive line from the control box directly to the
vehicle battery.
Ground the negative wire from the control box by connecting it to an
unpainted area on your vehicle's frame.
Using a fuse tap, connect the 12V control wire from the control box to a
power source that turns on ONLY when the key is turned to ACC/ON or
a switched fuse position.
Some examples of these power sources are: radio, dome light or those
that are marked as accessory in your owner's manual or on your fuse
box cover diagram.
The kit will not function without this connection.
1.
2.
3.
4.
5.
6.
7.
8.
WHERE TO INSTALL
FRONT
REAR
FRONT
REAR
TOOLS REQUIRED
32
5/32-inch Drill Bit
7/64-inch Drill Bit
Phillips Head Screwdriver
RECOMMENDED LOCATIONS FOR ROCK LIGHT PODS
If you are uncomfortable performing work of this nature yourself, then do
not hesitate to consult a professional for help. Working with a vehicle’s
electrical system can be hazardous to an unqualified individual. OPT7 is not
liable for damages or personal injuries while installing this product. The
installation guide is provided as assistance to reduce set up time.
/