ESAB Spool Hub Assembly for Fabricator 211i & 252i Transmig 200i & 250i Assembly Instruction

Brand: ESAB

Model: Spool Hub Assembly for Fabricator 211i & 252i Transmig 200i & 250i

Type: Assembly Instruction

SPOOL HUB ASSEMBLY INSTRUCTIONS

0-5223 1 December 22, 2011

Spool Hub Assembly Installation

The following components are included in this kit.

Item Description Qty

1 Fibre Washer 1

2 Spool Hub 1

3 Flat Washer Large Hole 1

4 Keyed Washer 1

5 Spring 1

6 Flat Washer Small Hole 1

7 Trib-lobe Nut 1

8 Retaining Clip 1

Art # A-10929

Axle

1. Install parts numbered 1 to 6 over the axle in the sequence shown above. Align the ﬂat edge of the Fibre

Washer with the ﬂat edge of the recess in the Spool Hub.

2. Install the Tri-lobe Nut (7) into the Axle through parts numbered 6, 5, 4 and 3.

3. Insert the Retaining Clip (8) into one of the set holes on the Spool Hub (2).

NOTE

Normally, the Spool Hub Assembly has been installed to the power source as delivered from the fac-

tory. These installation procedures are designed for future replacement.

Thermadyne Holdings Corporation

Suite 300, 16052 Swingley Ridge Road

St. Louis, MO 63017, USA

Telephone: 1-800-426-1888 • Fax: 1-800-535-0557

Email: [email protected]

www.thermalarc.com

Manual 0-5223

Spool Hub Assembly for

Fabricator 211i & 252i

Transmig 200i & 250i

Part Number: W7005311

Assembly Instructions

SPOOL HUB ASSEMBLY INSTRUCTIONS

December 22, 2011 2 0-5223

Wire Spool Installation

1. Remove the Spool Hub Retaining Clip from the spool hub.

2. Place Wire Spool onto the hub, loading it so that the wire will feed off the bottom of the spool as the spool

rotates counter clockwise. Make sure to align the spool alignment pin on the hub with the mating hole in

the wire spool.

3. Replace the Wire Spool Hub Retaining Clip in the set of holes closest to the spool, inner holes for

12.5lb/5.66kg (8"/200mm diameter) spool while outer holes for 33lb/15kg (12"/300mm diameter) spool.

Spool Hub Retaining Clip

Tri-lobe Nut

12.5lb / 8”

(5.66kg / 200mm)

Wire Spool

Spool Hub Aligenment Pin

Art # A-10933

Tri-lobe Nut

Spool Hub Retaining Clip

Spool Hub Aligenment Pin

33lb / 12”

(15kg / 300mm)

Wire Spool

NOTE

The Hub tension has been pre-adjusted at the factory. However if it is considered necessary, adjust-

ment can be made by turning the tri-lobe nut inside the open of the hub. For detailed adjustment, refer

to Wire Reel Brake chapter in section 3 in the operating manual.

CAUTION

Use care in handling the spooled wire as it will tend to “unravel” when loosened from the spool.

Grasp the end of the wire ﬁrmly and don’t let go of it.

Printed in: U.S.A

W ORLD HEADQUARTERS : 16052 Swingley R idge Road, Suite 300 • St. Louis, Missouri 63017 U.S.A.

A Global Cutting & Welding Market Leader

™

U.S. Customer Care: 800-426-1888 /

FAX

800-535-0557

•

Canada Customer Care: 905-827-4515 /

FAX

800-588-1714

International Customer Care: 940-381-1212 /

FAX 940-483-8178

•

www.thermalarc.com

Denton, TX USA

U.S. Customer Care

Ph: 1-800-426-1888 (tollfree)

Fax: 1-800-535-0557 (tollfree)

International Customer Care

Ph: 1-940-381-1212

Fax: 1-940-483-8178

Miami, FL USA

Sales Office, Latin America

Ph: 1-954-727-8371

Fax: 1-954-727-8376

Oakville, Ontario, Canada

Canada Customer Care

Ph: 1-905-827-4515

Fax: 1-800-588-1714 (tollfree)

Chorley, United Kingdom

Customer Care

Ph: +44 1257-261755

Fax: +44 1257-224800

Milan, Italy

Customer Care

Ph: +39 0236546801

Fax: +39 0236546840

Cikarang, Indonesia

Customer Care

Ph: 6221-8990-6095

Fax: 6221-8990-6096

Rawang, Malaysia

Customer Care

Ph: +603 6092-2988

Fax: +603 6092-1085

Melbourne, Australia

Australia Customer Care

Ph: 1300-654-674 (tollfree)

Ph: 61-3-9474-7400

Fax: 61-3-9474-7391

International

Ph: 61-3-9474-7508

Fax: 61-3-9474-7488

Shanghai, China

Sales Office

Ph: +86 21-64072626

Fax: +86 21-64483032

Singapore

Sales Office

Ph: +65 6832-8066

Fax: +65 6763-5812

THE AMERICAS EUROPE ASIA/PACIFIC

ESAB Spool Hub Assembly for Fabricator 211i & 252i Transmig 200i & 250i Assembly Instruction

ESAB Spool Hub Assembly for Fabricator 211i & 252i Transmig 200i & 250i Assembly Instruction

ESAB Spool Hub Assembly for Fabricator 211i & 252i Transmig 200i & 250i Assembly Instruction

Related papers

Other documents