ESAB Firepower Mig Spool Gun User manual

Brand: ESAB

Model: Firepower Mig Spool Gun

Type: User manual

This manual is also suitable for

MIG Spool Gun

VictorTechnologies.com

Aluminum Alloy

Firepower

MIG Spool Gun

Safety and

Operating

Instructions

Revision: AA Issue Date: August 2, 2014 Manual No.: 0-5362

www.firepower.com

MAX OUTPUT

160

AMPS

MIG

ALUMINUM

MATERIALS

FLEXIBLE G ASES

INERT

ARGON

WE APPRECIATE YOUR BUSINESS!

Congratulations on receiving your new Firepower product. We are proud to have

you as our customer and will strive to provide you with the best service and

support in the industry. This product is backed by our extensive warranty and

world-wide service network.

We know you take pride in your work and we feel privileged to provide you with

this high performance product that will help you get the job done.

YOU ARE IN GOOD COMPANY!

Firepower is a Global Brand of Arc Welding Products for Victor Technologies Inc.

We distinguish ourselves from our competition through market-leading innovation

and truly dependable products that will stand the test of time.

We strive to enhance your productivity, efﬁciency and welding performance

enabling you to excel in your craft. We design products with the welder in mind

delivering- advanced features, durability, ease of use and ergonomic comfort.

Above all, we are committed to a safer working environment within the welding

industry. Your satisfaction with this product and its safe operation is our ultimate

concern. Please take the time to read the entire manual, especially the Safety

Precautions.

If you have any questions or concerns regarding your new Firepower product,

please contact our friendly and knowledgeable Customer Service Team at:

1-800-462-2782 (USA) and 1-905-827-4515 (Canada),

or visit us on the web at www.Firepower.com

WARNINGS

Read and understand this entire Manual and your employer’s safety practices

before installing, operating, or servicing the equipment. While the information

contained in this Manual represents the Manufacturer’s judgment, the Manufacturer

assumes no liability for its use.

Firepower Spool Gun: 1444-0894

Set-up and Safe Operating Procedures

Instruction Guide Number 0-5362

Published by:

Victor Technologies, Inc.

16052 Swingley Ridge Road,

Suite 300 St. Louis, MO 63017

USA

www.ﬁrepower.com

U.S. Customer Care: (800) 426-1888

Canada Customer Care: 905-827-4515

International Customer Care: (940) 381-1212

Reproduction of this work, in whole or in part, without written permission of the publisher is prohibited.

The publisher does not assume and hereby disclaims any liability to any party for any loss or damage

caused by any error or omission in this Manual, whether such error results from negligence, accident,

or any other cause.

Publication Date: Aug. 19, 2014

Record the following information for Warranty purposes:

Where Purchased:

Purchase Date:

Table of Contents

SECTION 1: SAFETY PRECAUTIONS ..............................................................1-1

SECTION 2: MODEL SPECIFICATIONS ...........................................................2-5

SECTION 3: INSTALLATION AND OPERATION ...............................................3-7

3.01 Connecting the spool gun ........................................3-7

3.02 Adjusting wire feed pressure and speed ..................3-8

3.03 Installing the wire spool ..........................................3-8

SECTION 4: CARE AND MAINTENANCE .......................................................4-11

4.01 Changing the contact tip ........................................4-11

4.02 Changing the wire conduit .....................................4-12

4.03 Changing the drive rolls ........................................4-13

SECTION 5: TROUBLESHOOTING CHECK LIST .............................................5-15

SECTION 6: REPLACEMENT PARTS LIST .....................................................6-16

FIREPOWER - LIMITED WARRANTY TERMS ................................................6-18

WARRANTY SCHEDULE ...............................................................................6-19

GLOBAL CUSTOMER SERVICE CONTACT INFORMATION Rear Cover

SET-UP AND SAFE OPERATING PROCEDURES

1-1

89200016

Safety Precautions

SECTION 1:

SAFETY PRECAUTIONS

WARNING

SERIOUS INJURY OR DEATH may result if welding and cutting equipment is not

properly installed, used, and maintained. Misuse of this equipment and other

unsafe practices can be hazardous. The operator, supervisor, and helper must read

and understand the following safety warnings and instructions before installing

or using any welding or cutting equipment, and be aware of the dangers of the

welding or cutting process. Training and proper supervision are important for a

safe work place. Keep these instructions for future use. Additional recommended

safety and operating information is referenced in each section.

ELECTRIC SHOCK CAN CAUSE INJURY OR DEATH

Install and maintain equipment in accordance with the National Electrical Code

(NFPA 70) and local codes. Do not service or repair equipment with power ON.

Do not operate equipment with protective insulators or covers removed. Service

or repair to equipment must be done by qualiﬁed and/or trained personnel only.

Do not contact electrically live parts. Always wear dry welding gloves that are in

good condition. Aluminized, protective clothing can become part of the electrical path. Keep oxygen

cylinders, chains, wires, ropes, cranes, and hoists away from any part of the electrical path. All

ground connections must be checked periodically to determine if they are mechanically strong,

and electrically adequate for the required current. When engaged in AC welding/cutting under

wet conditions or where perspiration is a factor, the use of automatic controls for reducing the

no load voltage is recommended to reduce shock hazards. Accidental contact must be prevented

when using open circuit voltage exceeding 80 volts AC, or 100 volts DC by adequate insulation

or other means. When welding is to be suspended for any length of time, such as during lunch or

overnight, all electrode holders and electrodes should be removed from the electrode holder and

the power supply should be turned OFF to prevent accidental contact. Keep MIG-Guns, electrode

holders, Tig torches, Plasma torches, and electrodes away from moisture and water. See safety

and operating references 1, 2, and 8.

SMOKE, FUMES, AND GASES CAN BE DANGEROUS TO YOUR HEALTH

Ventilation must be adequate to remove smoke, fumes, and gases during

operation to protect operators and others in the area. Vapors of chlorinated

solvents can form the toxic gas “Phosgene” when exposed to ultraviolet radiation

from an electric arc. All solvents, degreasers, and potential sources of these

vapors must be removed from the operating area. Use air-supplied respirators

if ventilation is not adequate to remove all fumes and gases. Oxygen supports, and vigorously

accelerates ﬁre and should never be used for ventilation. See safety and operating references

1, 2, 3, and 4.

1-2

SET-UP AND SAFE OPERATING PROCEDURES

89200016Safety Precautions

ARC RAYS, HOT SLAG, AND SPARKS CAN INJURE EYES AND BURN SKIN

Welding and cutting processes produce extreme localized heat and strong

ultraviolet rays. Never attempt to weld/cut without a federally compliant welding

helmet with the proper lens. A number 12 to 14 shade ﬁlter lens provides the

best protection against arc radiation. When in a conﬁned area, prevent the

reﬂected arc rays from entering around the helmet. Approved shielding curtains

and appropriate goggles should be used to provide protection to others in the surrounding area.

Skin should be protected from arc rays, heat, and molten metal. Always wear protective gloves

and clothing. All pockets should be closed and cuffs sewn shut. Leather aprons, sleeves, leggings,

etc. should be worn for out-of-position welding and cutting, or for heavy operations using large

electrodes. Hightop work shoes provide adequate protection from foot burns. For added protection,

use leather spats. Flammable hair preparations should not be used when welding/cutting. Wear

ear plugs to protect ears from sparks. Where work permits, the operator should be enclosed in

an individual booth painted with a low reﬂective material such as zinc oxide. See safety and

operating references 1, 2, and 3.

WELDING SPARKS CAN CAUSE FIRES AND EXPLOSIONS

Combustibles reached by the arc, ﬂame, ﬂying sparks, hot slag, and heated

materials can cause ﬁre and explosions. Remove combustibles from the work

area and/or provide a ﬁre watch. Avoid oily or greasy clothing as a spark may

ignite them. Have a ﬁre extinguisher nearby, and know how to use it. If welding/

cutting is to be done on a metal wall, partition, ceiling, or roof, precautions must

be taken to prevent ignition of nearby combustibles on the other side. Do not

weld/cut containers that have held combustibles. All hollow spaces, cavities, and containers

should be vented prior to welding/cutting to permit the escape of air or gases. Purging with inert

gas is recommended. Never use oxygen in a welding torch. Use only inert gases or inert gas

mixes as required by the process. Use of combustible compressed gases can cause explosions

resulting in personal injury or death. Arcing against any compressed gas cylinder can cause

cylinder damage or explosion. See safety and operating references 1, 2, 5, 7, and 8.

NOISE CAN DAMAGE HEARING

Noise from the air carbon-arc process can damage your hearing. Wear protective

hearing devices to ensure protection when noise levels exceed OHSA standards.

Adequate hearing protection devices must be worn by operators and surrounding

personnel to ensure personal protection against noise. See safety and operating

references 1, 2, and 6.

WARNING

WARNING: This product contains chemicals, including lead, known to the State of

California to cause birth defects and other reproductive harm. Wash hands after

handling.

SET-UP AND SAFE OPERATING PROCEDURES

1-3

89200016

SAFETY AND OPERATING REFERENCES

1. Code of Federal Regulations (OSHA) Section 29, Part 1910.95, 132, 133, 134, 139, 251,

252, 253, 254 and 1000. U.S. Government Printing Ofﬁce, Washington, DC 20402.

2. ANSI Z49.1 “Safety in Welding and Cutting”.

3. ANSI Z87.1 “Practice for Occupational and Educational Eye and Face Protection”.

4. ANSI Z88.2. “Standard Practice for Respiratory Protection”. American National Standards

Institute, 1430 Broadway, New York, NY 10018.

5. AWS F4.1. “Recommended Safe Practices for Welding and Cutting Containers”.

6. AWS C5.3. “Recommended Practices for Air Carbon-Arc Gouging and Cutting”. The

American Welding Society, 550 NW Lejeune Rd., P.O. Box 351040, Miami, FL 33135.

7. NFPA 51B. “Fire Prevention in Cutting and Welding Processes”.

8. NFPA-7. “National Electrical Code”. National Fire Protection Association, Battery Park,

Quincy, MA 02269.

9. CSA W117.2. “Safety in Welding, Cutting and Allied Processes”. Canadian Standards

Association, 178 Rexdale Blvd., Rexdale, Ontario, Canada M9W 1R3.

Safety Precautions

1-4

SET-UP AND SAFE OPERATING PROCEDURES

89200016

This Page Intentionally Blank

SET-UP AND SAFE OPERATING PROCEDURES

2-5

89200016

SECTION 2:

MODEL SPECIFICATIONS

Description Rating

Rated Welding Current C0

160A

Duty Cycle 20%

Wire Diameter (Normal) 0.023-0.035 (Normal)

Wire Diameter (Stainless Steel) 0.023-0.030 (Stainless Steel)

Maximum Wire Feed Speed 630 in./min. (16 m/min.)

Maximum Wire Spool Size

Diameter: 4” (100 mm)

Width: 1.75” (45 mm)

Motor Voltage 24V DC

Model Speciﬁcations

2-6

SET-UP AND SAFE OPERATING PROCEDURES

89200016

This Page Intentionally Blank

SET-UP AND SAFE OPERATING PROCEDURES

3-7

89200016

SECTION 3:

INSTALLATION AND OPERATION

3.01 CONNECTING THE SPOOL GUN

1. Make sure the welding

power source is turned

OFF before connecting

the welding gun.

2. Insert the gun connection

into the feeder receptacle,

aligning the conduit plug

ﬁrst, then the gas plug.

Push until all ﬁttings are

seated then tighten the

nut hand tight.

3. Connect gas supply ﬁtting and tighten with a wrench.

3A. Inlet - USA model 3B. Outlet

4. Align Control Plug to

panel ﬁtting and tighten

securely.

Installation and Operation

3-8

SET-UP AND SAFE OPERATING PROCEDURES

89200016

3.02 ADJUSTING WIRE FEED PRESSURE AND SPEED

1. Use a screwdriver to adjust the wire

feed pressure. Turn the adjusting

screw clockwise to decrease, or

counterclockwise to increase pressure

on the wire feed drive rolls.

2. Adjust the “AMP” (WIRESPEED) knob

on the power supply to adjust the wire

speed feed.

Direction Result

Clockwise Increase Speed

Counterclockwise Decrease Speed

3.03 INSTALLING THE WIRE SPOOL

1. Remove the spool cover by loosening

the cover screw by hand.

2. Slide the wire spool onto the shaft.

Installation and Operation

SET-UP AND SAFE OPERATING PROCEDURES

3-9

89200016

3. Press the red button on top of the gun

to release pressure from the drive rolls.

4. Push the wire through the guide and into

the wire feed drive rolls.

5. Make sure the welding power source is

turned ON before proceeding to step 6.

6. Press the trigger to feed the wire into

the conductor tube and cut the wire to

obtain the correct wire stick-out.

Installation and Operation

3-10

SET-UP AND SAFE OPERATING PROCEDURES

89200016

7. Adjust the friction nut on the spool shaft

to apply the correct wire tension. Spool

should stop when trigger is released.

8. Replace the wire spool cover and hand

tighten the cover screw.

Installation and Operation

SET-UP AND SAFE OPERATING PROCEDURES

4-11

89200016

SECTION 4:

CARE AND MAINTENANCE

4.01 CHANGING THE CONTACT TIP

NOTE

Replace contact tip if hole is enlarged or deformed.

1. Select the correct contact tip according

to the wire used.

2. Remove the nozzle from the gun to

reveal the contact tip.

3. Remove the contact tip using pliers if

needed. Replace contact tip and tighten

securely.

NOTE

Periodically clean spatter from the inside of the nozzle and holes of the gas diffuser.

Use anti-spatter spray for best results.

Care and Maintenance

4-12

SET-UP AND SAFE OPERATING PROCEDURES

89200016

4.02 CHANGING THE WIRE CONDUIT

NOTE

Replace liner if hole is obstructed. Make sure the end of the liner is smooth.

1. Turn the power source OFF and

disconnect the gun.

2. Unscrew the nozzle and remove it

from the conductor tube.

3. Remove the diffuser from the

conductor tube using a wrench.

Care and Maintenance

SET-UP AND SAFE OPERATING PROCEDURES

4-13

89200016

4. Remove the conductor tube by

unscrewing the nut at the base.

5. Pull the liner out and replace.

Repeat steps 1-4 in reverse order to

reassemble the gun.

4.03 CHANGING THE DRIVE ROLLS

NOTE

Turn power supply OFF before replacing drive rolls.

1. Remove the screws which secure the

upper and lower drive rolls. It may be

necessary to remove drive roll side of

gun case to change lower drive roll

(see steps 2 and 3).

2. Loosen four handle screws. Turn

ring on the bottom of the handle

(surrounding the speed control knob)

one-quarter turn counter-clockwise,

and remove.

Care and Maintenance

4-14

SET-UP AND SAFE OPERATING PROCEDURES

89200016

3. Remove one screw holding each

drive roll in place. Press the red

button on top of the gun to relieve

pressure on the rolls if necessary.

Remove the drive rolls, and install the

new drive rolls in reverse order.

4. Perform steps 1-3 in reverse order to

reassemble the gun.

Care and Maintenance

SET-UP AND SAFE OPERATING PROCEDURES

5-15

89200016

SECTION 5:

TROUBLESHOOTING CHECK LIST

Problem Possible Cause Corrective Action

Drive rolls turn

but wire will

not feed or wire

is not feeding

through

Incorrect drive rolls

Be sure the wire diameter being used is

stamped on the drive rolls. Replace drive

rolls if necessary.

Incorrect drive roll

pressure

Check and correct drive roll pressure. Turn

pressure adjusting screw clockwise until

the wire feeds properly or doesn’t slip.

(See page 3-6)

Worn or dirty drive rolls Clean or replace drive rolls.

Incorrect wire spool

friction

Adjust the friction nut on the spool shaft to

ﬁnd the correct wire tension.

(See page 4-8)

Worn or dirty outlet liner Clean or replace liner.

Rusty or dirty wire Replace wire. (See page 3-6)

Partially arced, melted, or

improper size contact tip

Replace contact tip.

Variable arc

Contact tip worn or

incorrect size

Replace contact tip.

Incorrect wire feed speed

Adjust wire speed by turning speed

control knob clockwise (to max) or

counter-clockwise (to min). (See page 3-6)

Troubleshooting Check List

6-16

SET-UP AND SAFE OPERATING PROCEDURES

89200016

SECTION 6:

REPLACEMENT PARTS LIST

Ref

Stock

Number Part Number Description

Image

1110-1100 11-23 Contact Tip .023 (0.6 mm)

1110-1101 11-30 Contact Tip .030 (10.8 mm)

1110-1102 11-35 Contact Tip .035 (10.9 mm)

1210-1300 21T-37 Nozzle 3/8" (9.5 mm)

1210-1100 21-37 Nozzle 3/8" (9.5 mm)

1210-1110 21-50 Nozzle 1/2" (12.7 mm)

1210-1112 21-50F Nozzle 1/2" (12.7 mm)

1210-1120 21-62 Nozzle 5/8" (15.9 mm)

3 1510-1101 51 Gas Diffuser

4 2031-2107 SPG66065 Conduit

5 2031-2227 WSPDRC Drive Roll Cover

Replacement Parts List

Page is loading ...

ESAB Firepower Mig Spool Gun User manual

Brand: ESAB

Model: Firepower Mig Spool Gun

Type: User manual

This manual is also suitable for

MIG Spool Gun

Download PDF

report

ESAB Firepower Mig Spool Gun User manual

This manual is also suitable for

ESAB Firepower Mig Spool Gun User manual

Related papers

Other documents