Saab 12 787 146 Installation Instructions Manual

Saab
Brand
Saab
Model
12 787 146
Type
Installation Instructions Manual

This manual is also suitable for

Saab 12 787 146 is a CD changer kit designed for use in Saab 9-3 M03 vehicles. It includes a CD changer, a fiber-optic cable and the necessary mounting hardware. The CD changer can hold up to six CDs, allowing you to enjoy your music without having to constantly change discs. The fiber-optic cable allows the CD changer to communicate with the head unit, so you can control the CD changer from the head unit's controls. The kit also includes a transport fuse, which must be inserted into the CD changer before it can be used.

Saab 12 787 146 is a CD changer kit designed for use in Saab 9-3 M03 vehicles. It includes a CD changer, a fiber-optic cable and the necessary mounting hardware. The CD changer can hold up to six CDs, allowing you to enjoy your music without having to constantly change discs. The fiber-optic cable allows the CD changer to communicate with the head unit, so you can control the CD changer from the head unit's controls. The kit also includes a transport fuse, which must be inserted into the CD changer before it can be used.

Saab 9-3 M03-
900 Installation instructions
SCdefault
MONTERINGSANVISNING
·
INSTALLATION INSTRUCTIONS
MONTAGEANLEITUNG
·
INSTRUCTIONS DE MONTAGE
SITdefault
Saab 9-3 M03-
CD player/CD changer
Accessories Part No. Group Date Instruction Part No. Replaces
12 787 146
12 787 152 9:85-23 Jan 03 12 788 458 12 788 458 Aug 02
F930A055
2 12 788 458
Saab 9-3 M03-
12 787 146 CD changer kit
1 CD changer
2 Fibre-optic cable
12 787 152 CD player kit
1 CD player
2 Fibre-optic cable
To fit CD player/CD changer, see page 3
To replace CD player with CD changer, see page 10
F930A056
1
2
12 788 458 3
Saab 9-3 M03-
To fit CD player/CD changer
1 Remove the climate system control panel by pull-
ing it out carefully. Use removal tool 82 93 474.
2 Remove the control panel connectors.
3 Remove the cover located below the ACC or
MCC unit.
4 Remove the entertainment head unit by pushing
in the two catches.
5 Remove the head unit connectors.
F930A057
2
2
5
4
4
5
1
4 12 788 458
Saab 9-3 M03-
6 Remove the centre dashboard vent by carefully
bending in the three upper hooks which are
accessible through the grille while simultaneously
pulling the guide pin straight out.
7 Remove the infotainment system control panel.
8 Lift out the control panel and remove the
connector.
Important
Take care to bend the correct hooks. Hooks holding
together the air outlet are also visible behind the
grille.
WARNING
The visible red light is a class 1 laser. Do not look
directly into the optical fibre or the control module
connector at close range. A distance of less than
20 mm between your eyes and the light source may
cause eye injury.
F930A058
77
8
6
12 788 458 5
Saab 9-3 M03-
9 Remove the fibre optic cable connector (small
connector) from the control panel connector.
10 Remove the fibre optic cable connected to posi-
tion 1 by opening the connector locking clip and
carefully lifting the hook.
11 Insert the long section of the fibre optic cable in
the accessory kit along the car's normal cable
harness inside the dashboard.
12 Remove the protective cover from the connection
on the accessory kit fibre optic cable.
13 Fit the protective cover onto the removed fibre
optic cable connection and carefully move the
fibre optic cable aside in order to prevent damage.
14 Fit the accessory kit fibre optic cable connection
in position 1 in the small connector to the control
unit. Fit the locking clip.
15 Fit the small connector to the large connector.
Important
Handle the fibre-optic cables with care or the signal
may be distorted.
· It is very important that the two leads in the
connector are not confused with one another.
· Do not splice the cables.
· Do not bend the cable in a radius smaller than
25 mm.
· Do not expose the cable to temperatures
exceeding 85 °C.
· Keep the cable ends free from dirt and grime.
· Do not expose the cable to impact as this may
cause the transparent plastic to whiten, thereby
reducing the intensity of the light and causing
possible communication interruptions.
· The cable should not lie against any sharp edges
as this may cause increased signal reduction.
F930A059
109
6 12 788 458
Saab 9-3 M03-
16 Plug in the control panel connector and fit the
control panel.
17 Fit the dashboard vent.
F930A060
17
16
16 16
12 788 458 7
Saab 9-3 M03-
18 Remove the small connector from the large
connector for the entertainment head unit.
19 Remove the fibre optic cable which is connected
to position 2 by opening the connector locking
clip and carefully lifting the hook.
20 Remove the protective cover from the connection
on the accessory kit fibre optic cable.
21 Fit the protective cover onto the removed fibre
optic cable connection.
22 Fit the connection on the accessory kit fibre optic
cable to position 2 in the small connector in the
entertainment head unit. Fit the locking clip.
23 Fit the small connector to the large connector.
Important
Take note of the location of the small connector
since it is possible to fit the connector incorrectly.
Important
Take note of the small connector location since it
is easy to fit the connector incorrectly.
F930A061
23
18
19
8 12 788 458
Saab 9-3 M03-
24 Find the power supply for the CD player/CD
changer in cable harness. The connector is
secured with a bit of tape to the cable trunk behind
the location for the entertainment head unit.
Remove the bit of tape and pull the cable harness
forwards.
25 Remove the transport fuse placed on the top side
of the CD player/CD changer. Insert and fit the
CD player/CD changer in the entertainment head
unit bracket.
26 Fit the connector for CD player/CD changer power
supply in the connector for the accessory kit fibre
optic cable.
F930A062
24
25
26
12 788 458 9
Saab 9-3 M03-
27 Plug in the connector to the entertainment head
unit.
28 Plug in the connector to the CD player/CD
changer.
29 Fit the entertainment head unit.
30 Connect and fit the climate system control panel.
31 Connect the diagnostic tool, select car and model
year, select “All”, select “Add/Remove”, select the
accessory and then “Add”.
32 Check CD player/CD changer function.
F930A063
30
30
30
27
27
28
29
10 12 788 458
Saab 9-3 M03-
Switch from CD player to CD changer.
– Connect the diagnostic tool, select car and model
year, select “All”, select “Add/Remove”, select the
accessory and then “Remove”.
– Perform steps 1-5 in this installation instruction.
– Remove the connector from the CD player.
– Remove the CD player with removal tool
84 71 203.
– Perform step 25 and steps 27-32 in this installation
instruction.
– Connect the diagnostic tool, select car and model
year, select “All”, select “Add/Remove”, select the
accessory and then “Add”.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10

Saab 12 787 146 Installation Instructions Manual

Saab
Brand
Saab
Model
12 787 146
Type
Installation Instructions Manual
This manual is also suitable for

Saab 12 787 146 is a CD changer kit designed for use in Saab 9-3 M03 vehicles. It includes a CD changer, a fiber-optic cable and the necessary mounting hardware. The CD changer can hold up to six CDs, allowing you to enjoy your music without having to constantly change discs. The fiber-optic cable allows the CD changer to communicate with the head unit, so you can control the CD changer from the head unit's controls. The kit also includes a transport fuse, which must be inserted into the CD changer before it can be used.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents